Transcript Networking_Extension Numbering_overlap_rev2

Networking by Extension Numbering
rev2
Use SIPGW Loopback as Virtual CO
1
Configuration
System Connection Diagram
Virtual CO
4770109
NCP1000 _2
V-SIPGW Loopback
4770102
V-IPGW
NCP1000
ICPMPR(192.168.0.101)
DSP(192.168.0.102)
PBX PW：1234
ICPMPR(192.168.0.150)
DSP(192.168.0.151)
PBX PW：1234
Extension
No.380
CLIP :
4770380
V-IPGW
L2 Switch
TDE600
LAN (192.168.0.11)
VM PW：1234
Extension
No.101
CLIP :
4770101
TVM
DID table:
4770101
4770102
4770109
4770251
4770380
V-IPGW
Extension
No.251
VM Number 400
-> 101
-> 102
-> 109
-> 251
-> 380
CLIP :
IP Address
192.168.0.159
ICPMPR(192.168.0.111)
DSP(192.168.0.112)
PBX PW：1234
4770251
2
How to set up Networking?
3
NCP1000 side
1)Assign No of IP Trunk
4
NCP1000 side
2)Assign V- IPGW16 card
3)OUS V- IPGW16
4)Open “Shelf Property” of VIPGW16
5
NCP1000 side
5)Open “GW Setting”
6
NCP1000 side
6) Assign MPR IP Address of TDE600 and NCP100_2
7
NCP1000 side
7) Open “DN2IP”
8
NCP1000 side
8) Assign Remaining Number of Digits and GW No.
9
NCP1000 side
10) Open “System-Timers & Counters”
Change “Extension Inter-digit (s)” to “4”
10
NCP1000 side
11) Delete Leading number of TDE600 “2” and NCP1000_2 “3”
11
NCP1000 side 12) Assign Leading number of TDE600 “2” and NCP1000_2 “3”
12
NCP1000 side
13) Assign V-IP Trunk Group “7” and V-SIP Trunk Group “2”
V-IPGW16 Trunk Group keep “7” as default from Ver4
13
NCP1000 side
14) Trunk Group COS setting “7” -> “1”
Trunk G 7 for IPGW
This setting necessary to realize all CO outgoing
through NCP1000.
14
NCP1000 side
15) Change Local Access Priority
This setting necessary to realize all CO outgoing
through NCP1000.
15
TDE600 side
1) Assign No of IP Trunk
16
TDE600 side
2) Assign V- IPGW16 card
3) OUS V- IPGW16
4) Open “Shelf Property” of VIPGW16
17
TDE600 side
5) Open “GW Setting”
18
TDE600 side
6) Assign MPR IP Address of NCP1000 and NCP1000_2
19
TDE600 side
7) Open “DN2IP”
20
TDE600 side
8) Assign Remaining Number of Digits and GW No.
21
TDE600 side
10) Open “System-Timers & Counters”
Change “Extension Inter-digits(s)” to “4”
22
TDE600 side
11) Delete Leading number of NCP1000 “1”, NCP1000_2 “3” and “4” for VM
23
TDE600 side
12) Assign Leading number of NCP1000 “1”, NCP1000_2 “3” and VM “4”
24
TDE600 side
13) Assign V-IP Trunk Group “7”
V-IPGW16 Trunk Group assigned “7” as default from Ver4
25
NCP1000_2 side
1) Assign No of IP Trunk
26
NCP1000_2 side
2)Assign V- IPGW16 card
3)OUS V- IPGW16
4)Open “Shelf Property” of VIPGW16
27
NCP1000_2 side
5) Open “GW Setting”
28
NCP1000_2 side
6) Assign MPR IP Address of NCP1000 and TDE600
29
NCP1000_2 side
7) Open “DN2IP”
30
NCP1000_2 side
8) Assign Remaining Number of Digits and GW No.
31
NCP1000_2 side
10) Open “System-Timers & Counters”
Change “Extension Inter-digits(s)” to “4”
32
NCP1000_2 side
11) Delete Leading number of NCP1000 “1”, TDE600 “2” and “4” for VM
33
NCP1000_2 side
12) Assign Leading number of NCP1000 “1”, TDE600 “2” and VM “4”
34
NCP1000_2 side
13) Assign V-IP Trunk Group “7”
V-IPGW16 Trunk Group assigned “7” as default from Ver4
35
How to set up Networking DSS?
Ext 101 and Ext 380 want to monitor Ext 251
TDE600
NCP1000
Extension
No.101
IPGW
IPGW
Extension
No.251
IPGW
NCP1000_2
Extension
No.380
36
NCP1000 side
1) Assign Network EXT No “251”.
37
NCP1000 side
2) Assign Network PBX ID “1”.
38
NCP1000 side
3) Assign NDSS Key to EXT 101
“NDSS 251”
39
NCP1000_2 side
1) Assign Network EXT No “251”.
40
NCP1000_2 side
2) Assign Network PBX ID “3”.
41
NCP1000_2 side
3) Assign NDSS Key to EXT 380
“NDSS 251”
42
TDE600 side 1) Assign Network PBX ID “2”.
43
TDE600 side
2) Assign Monitored EXT No “101” and “380”
And slot No of GW
If several extension wants to monitor Ext251,
It is also available to assign “1** ” and “3** “
44
How to set up Centralized VM?
45
PBX side set up to make connection to VM
NCP1000 side
1) “OUS” the port connect TVM
2) Change port type from “Normal” to “VM(DPT)”
3) “INS” the port
46
PBX side set up to make connection to VM
NCP1000 side
4) Change VM EXT number to “400”
47
PBX side set up to make connection to VM
TDE600 side
1) Delete Floating Extension No
48
PBX side set up to make connection to VM
NCP1000_2 side
1) Delete Floating Extension No
49
VM side set up TVM and to create mail box by quick set up
1) LAN setting
50
VM side set up TVM and to create mail box by quick set up
2) Assign IP address
IP address of connected PBX
51
VM side set up TVM and to create mail box by quick set up
3) Activate quick set up
52
VM side set up TVM and to create mail box by quick set up
4) Maximum Extension Number Length to “8”
53
VM side set up TVM and to create mail box by quick set up
5) Create mail box for the EXT by manual
6) Assign Mail box No. “101” for Ext101, “105” for Ext301 and “107” for Ext2001
54
How to set up VM access key?
(Voice Mail Transfer Key)
55
PBX side set up to access to VM by VMT key
NCP1000 side
1)Assign VMT key with VM EXT No. ”400”
56
PBX side set up to access to VM by VMT key
TDE600 side
1)Assign Centralized VM Unit Setting “400”
57
PBX side set up to access to VM by VMT key
TDE600 side
2)Assign VMT key with VM EXT No. “400”
58
How to enable transfer back to EXT under PBX from Cell?
This function is only available in a call from trunk.
Virtual CO
Operation
V-SIPGW Loopback
NCP1000
1. “4770102” make a call to “4770101”
2. Then “4770101” call forward to “4770109”
3. “4770109” answer the forwarded call and press “#” + “104”
4770109
and hung, then this call transfer to Ext104.
4770102
Extension
No.101
Extension
No.104
CLIP :
4770101
Fwd to
4770109
59
PBX side set up to allow Cellular to EXT
NCP side
1)Change “Fwd/Transfer to Public CO” to “Enable”
2)Change “Transfer by “#”” to Enable
Enhanced Key Required
60
How to enable parallel ring for EXT and Cell?
61
PBX side (NCP1000, NCP1000_2, TDE600)
1)Change COS “Call FWD to CO” to “Enable”
62
PBX side (NCP1000, NCP1000_2, TDE600)
2)Change “Keep Ring after FWD N/A to CO” to Enable
EXT side
1)Set No Answer Fwd to cellular phone
63
How to start conference using Cellular Phone?
Virtual CO
V-SIPGW Loopback
NCP1000
LCOT port24 connect to SLC
Operation
A. DISA Security : None
1. “4770109” make a call to DISA“4770501”
2. Press *37024 (catch LCOT port)
3. Then press 921# (92 : Conference Group Call access code)
B. DISA Security : Trunk or All (with PIN)
1. “4770109” make a call to DISA“4770501”
2. Press *471041234
3. Press *37024 (catch LCOT port)
4. Then press 921# (92 : Conference Group Call access code)
4770109
Extension
No.101
Extension
No.102
DID table:
4770501 -> 501
C. DISA Security : Trunk or All (without PIN)
1. “4770109” make a call to DISA“4770501”
2. Press *37024 (catch LCOT port)
3. Then press 921# (92 : Conference Group Call access code)
64
Common Setting
1) Trunk Group COS setting “7” -> “1”
Trunk G 2 for SIPGW
65
Common Setting
2) Change “Conference Group Call Operation” Access Code “ *32 ” -> “ 92 ”
It is also necessary to change “Operator Call” Access Code “ 9 ” -> “ 91 ”
This setting is only example for demonstration,
It is able to change other digits.
This setting is necessary to prevent that return to DISA Top Menu.
66
Common Setting
3) Enable “DISA to Public CO”
67
A. DISA Security : None
4) Select DISA Security Mode “ None ”
68
B. DISA Security : Trunk or ALL (with PIN)
4) Select DISA Security Mode “ Trunk ” or “ ALL “
5) Select Remote Walking COS through DISA without PIN “ Disable “
69
B. DISA Security : Trunk or ALL (with PIN)
6) Assign Extension PIN “ 1234 “ to Ext104
70
C. DISA Security : Trunk or ALL (without PIN)
4) Select DISA Security Mode “ Trunk ” or “ ALL “
5) Select Remote Walking COS through DISA without PIN “ Enable “
71
C. DISA Security : Trunk or ALL (without PIN)
6) Assign system speed dial
0 + Cellular Phone Number
72
How to set up V-SIPGW loopback for Virtual CO
It is necessary to use DSP16 or DSP64.
73
NCP1000 side
1)Assign No of SIP-GW channel
4ch for IP-GW
4ch for SIP-GW
If use DSP16, it is necessary to install AKY for 4ch IP Trunk.
74
NCP1000 side
2)Assign V- SIPGW16 card
3)OUS V- SIPGW16
4)Open “Port Property” of V-SIPGW16
75
NCP1000 side
5)Assign Channel Attribute
1port for Basic channel
3port for Additional channel for Basic channel
76
NCP1000 side
6) Assign Own IP Address (192.168.0.101)
7) Change SIP Server Port Number to “35060”
77
NCP1000 side
8) Assign “User Name”, “Authentication ID” and “Authentication Password”
78
NCP1000 side
9) Change Register Ability to “Disable”
79
NCP1000 side
10) Change From Header in Calling Party to “PBX-CLIP”
11) INS V-SIPGW16
80
NCP1000 side
12) Set DDI/DID Number
This setting is necessary to receive the CO call.
81
How to send CLIP ID of remote site to CO line?
It is necessary to use ARS.
82
Remote side (NCP1000_2, TDE600)
1) Change “ARS Mode” to ”On for Any CO Access Operation”
83
Remote side (NCP1000_2, TDE600)
2) Assign Leading Number “477” and Additional Number of Digits “4”
84
Remote side (NCP1000_2, TDE600)
3) Assign Carrier Access Code “0” in Carrier 1
85
Remote side (NCP1000_2, TDE600)
4) Change Trunk Group for Carrier 1 to “TRG07 ON”
86