Transcript Panasonic NS1000 legacy guide

Legacy Adaptor (KX-NS8290） Test Environments Setup Manual
1. Example of test configuration
-> Please refer to TEST Config page.
2. NS1000 setup procedure
-> Please refer to NS1000 SETUP page.
(1) KX-NS1000 (Ver 002.xxxx) Setup Procedure
(2) KX-NS1000 (Ver 001.xxxx) Setup Procedure
3. Legacy Adaptor setup procedure
-> Please refer to NS8290 SETUP page.
(1)Initial Configuration
(2)Setting for the test configuration
4. Legacy Adopter Log capture manual
-> Please refer to Log Capture page.
TEST
Config
Legacy Adaptor (KX-NS8290)
PRI30 Line Status
System Status
SPEED
PRI30
LINK/ACT
AC-Adaptor
VoIP LAN
Initial SW
TEST
Config
Example of test configuration
PRI Network
*According to the your test
environment, please set a fixed
IP address for the NS8290 and
NS1000.
Legacy Adaptor
IP=192.168.0.151 (default)
AC-Adaptor
Ether
Fast Ether (100M)
L2SW with or without PoE
Ether
Ether
PC for
Web-MC
Not use PRI23 port
KX-NS1000
IP=192.168.0.101
(default)
Analog TEL(2W)
IP-PT
TEST
Config
Legacy Adaptor Test Logical Channel Connection
Legacy Adaptor
SLT I/F
ex101
IP-PT I/F
SIP Trunk
SIP Server
SIP-Trunk I/F #01
SIP ID #401
SIP-Trunk I/F #02
SIP ID #402
SIP-Trunk I/F #03
SIP ID #403
・
・
・
・
・
・
SIP-Trunk I/F #23
or
ex103
SIP-Trunk I/F #30
SIP ID #423
or
SIP ID #430
PRI Network
PR I/F
KX-NS1000
KX-NS1000 (Ver 002.xxxx) Setup Procedure (1/7)
1)Select [Virtual]
2)Select [V-SIPGW16]
3)Set Total number of cards as 2.
4)Set to the [OUS] state for each slot.
NS1000
SETUP
KX-NS1000 (Ver 002.xxxx) Setup Procedure (2/7)
1)Select [Port Propertty]
NS1000
SETUP
KX-NS1000 (Ver 002.xxxx) Setup Procedure (3/7)
1)Select [Trunk Adopyer]
NS1000
SETUP
NS1000
SETUP
KX-NS1000 (Ver 002.xxxx) Setup Procedure (4/7)
1)Set the Trunk Adaptor IP
address of port1
2)Push Apply button
3)Push Next button
NS1000
SETUP
KX-NS1000 (Ver 002.xxxx) Setup Procedure (5/7)
1)Push Finish button
NS1000
SETUP
KX-NS1000 (Ver 002.xxxx) Setup Procedure (6/7)
1) check that the setting of
IP address are reflected
in each port
KX-NS1000 (Ver 002.xxxx) Setup Procedure (7/7)
1)Set to the [INS] state for each slot.
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (1/6)
1)Push [Virtual] button
NOTE
In case of PBX Version of NS1000 is Ver 001.xxxx, must be
installed in advance 16ch IP-TRUNK license key X 2 licences.
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (2/6)
1)Select [V-SIPGW16] tab
2)Set Total number of cards as 2.
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (3/6)
1)Set to the [OUS] state for each slot.
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (4/6)
1)Select [Port Property] menu
NS1000
SETUP
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (5/6)
Please set the parameters of the port properties as follows.
In case of parameters except [User Name] and [Authentication ID] can be
set all ports by using COPY function.
In case of [User Name] and [Authentication ID], please configure each port
No
Slot
Port
Main
Account
Register
Channel
Attribute
SIP Server
IP Address
User
Name
Authenti
-cation ID
Authenti
-cation Pass
Register
Server
IP Address
1
31
1
Basic Channel
192.168.0.151
401
401
1234
192.168.0.151
2
31
2
↓
↓
402
402
↓
↓
3
31
3
↓
↓
403
403
↓
↓
4
31
4
↓
↓
404
404
↓
↓
～
31
～
↓
↓
～
～
↓
↓
13
31
13
↓
↓
413
413
↓
↓
14
31
14
↓
↓
414
414
↓
↓
15
31
15
↓
↓
415
415
↓
↓
16
31
16
↓
↓
416
416
↓
↓
17
32
1
↓
↓
417
417
↓
↓
18
32
2
↓
↓
418
418
↓
↓
19
32
3
↓
↓
419
419
↓
↓
20
32
4
↓
↓
420
420
↓
↓
～
32
～
↓
↓
～
～
↓
↓
29
32
13
↓
↓
429
429
↓
↓
NS1000
SETUP
KX-NS1000 (Ver 001.xxxx) Setup Procedure (6/6)
Activate the virtual card to push the
[INS] button for each slot..
Initial Configuration (1/7)
NS8290
SETUP
Username ⇒ INSTALLER
Ｐａｓｓｗｏｒｄ ⇒ 1234
http://192.168.0.151/WebMC/users/login
NS8290
SETUP
Initial Configuration (2/7)
1)Push Install button
NS8290
SETUP
Initial Configuration (3/7)
1)Push Next button
NS8290CE
SETUP
Initial Configuration (4/7)
1)Push next button
NS8290
SETUP
Initial Configuration (5/7)
1)According to the your test
environment, set a fixed
IP address
1)Push next button
NS8290
SETUP
Initial Configuration (6/7)
1)Push next button
NS8290
SETUP
Initial Configuration (7/7)
1)Please set KX-NS8290CE password
2)Push next button
Setting for the test configuration (1/9)
1)After all the initialization procedure finished,
KX-NS8290CE will display this home menu.
2)Please push this icon, and enter the path
configuration menu.
NS8290
SETUP
Setting for the test configuration (2/9)
2)Push [OUS] button
1)Enter the SIP card property menu
by select the [2.SIP Card Property]
NS8290
SETUP
NS8290
SETUP
Setting for the test configuration (3/9)
1) Set with reference to
the note below
2)Push Apply
NOTE
If the PBX Version of NS1000 is Ver 001.xxxx, please set the Activation
Key Mode as "YES". In that case, Authentication ID setting of "SIP
port Property" shown in the following pages, is required.
Otherwise, the settings that are shown in this and subsequent
pages is not required.
Setting for the test configuration (4/9)
1)Enter the SIP port property menu
by select the [3.SIP Port Property]
NS8290
SETUP
NS8290
SETUP
Setting for the test configuration (5/9)
1)Set the [Authntication Password]
of port1 as 1234.
2)Push the [Copy] button
NS8290
SETUP
Setting for the test configuration (6/9)
1) Click here
2)Select the port number, from port2
until port30
3) Push [Copy] button
Setting for the test configuration (7/9)
1)Enter the SIP card property menu
by select the [2.SIP Card Property]
NS8290
SETUP
Setting for the test configuration (8/9)
1)Push [INS] button
NS8290
SETUP
NS8290
SETUP
Setting for the test configuration (9/9)
1)After all the settings has been
completed, please save the system
data
2) When you close the Web maintenance
console, please press the [LOGOUT] button
Log
Capture
Legacy Adaptor Error Log Capture
2) Push [Minor] Button
1) Utility -> 3.Log -> 1.Error Log
3) Push [Save] Button to
store data to PC
Log
Capture
Legacy Adaptor Syslog Capture
1) Utility -> 3.Log -> 2. Syslog
2) Push [Save] Button to
store data to PC
Log
Capture
Legacy Adaptor ISDN/QSIG Protocol Trace Capture
3) Push [Start] Button
2) Select [Accumulation Trace]
4) Push [Capture] Button
to store data to PC
1) Utility -> 4.Monitor/Trace -> 1.ISDN/QSIG Protocol Trace