Gold Abutment for crown - Toledo Perio
Download
Report
Transcript Gold Abutment for crown - Toledo Perio
Gold Abutment
for crown
Gold abutment
NC
Product portfolio
RC
For NC and RC
STRAUMANN
Education
2
Gold abutment
Concept
Intended use
Screw- or cement-retained crowns
Cement-retained bridges via mesostructure
Telescopic bridgeworks or telescopic
crowns
Component materials
Gold Abutment (non-oxidizing Gold)
Basal Screw (TAN – TAN is one type
of titanium alloy material)
Modeling Aid (Polymer)
Benefits
Precise wax modelation
Safe cast-to procedures
Esthetic solution even with thin mucosa biotype
The Gold abutment is not suitable for direct splinting
STRAUMANN
Education
3
Gold abutment – Lab procedures
Step 1- Preparation
Fabricate a master cast
Make a diagnostic wax-up
Make a silicone key
STRAUMANN
Education
4
Gold abutment – Lab procedures
Hand-tighten Gold Abutment onto analog
Shorten burn-out modeling aid to height of occlusal plane
Attach Gold Abutment to polishing aid for easier handling
STRAUMANN
Education
5
Gold abutment – Lab procedures
Step 2 - Wax modeling
Wax layer must be at least 0.7 mm thick
Do not cover margins of abutment with wax
For sharp-edged finish of screw channel, use modeling aid
STRAUMANN
Education
6
Gold abutment – Lab procedures
For proper hygiene: Cement margin must be no more than 2.0
mm below gingival level
STRAUMANN
Education
7
Gold abutment – Lab procedures
Step 3 - Investing of customized abutment
Do not use wetting agents
Thoroughly clean abutment before investing
Remove all wax particles (use insulating agents)
Invest customized abutment in usual method
STRAUMANN
Education
8
Gold abutment – Lab procedures
No wax on delicate margins
Speed investment materials are not recommended
Invest following the manufacturers’ instructions
Follow recommended mixing ratio and preheating time
STRAUMANN
Education
9
Gold abutment – Lab procedures
Step 4 - Devesting
Devest abutment with ultrasound, waterjet, pickling acid or
glass fiber brush
Always devest with a polishing aid to protect the implantabutment connection
STRAUMANN
Education
10
Gold abutment – Lab procedures
Never sand-blast to devest without mounting abutment
on polishing aid!
STRAUMANN
Education
11
Gold abutment – Lab procedures
Casting errors and incorrect handling
Procedure must be repeated if:
The casting gold did not flow out sufficiently
STRAUMANN
Education
12
Gold abutment – Lab procedures
Casting errors and incorrect handling
Intruded casting metals and casting pearls cannot be
removed from the connection part of the Gold Abutment!
STRAUMANN
Education
13
Gold abutment – Lab procedures
Casting errors and incorrect handling
The Ceramicor® alloy surface cannot be covered with
ceramic veneering material.
Ceramicor® is a non-oxidizing alloy and allows no ceramic
bonding
STRAUMANN
Education
14
Gold abutment – Lab procedures
Step 5 - Fabricate the cement-retained single crown
Trim and polish the abutment
STRAUMANN
Education
15
Gold abutment – Lab procedures
Block out screw channel
Wax framework directly on top
Silicone key shows relations for restoration
STRAUMANN
Education
16
Gold abutment – Lab procedures
Cast framework in conventional manner
Trim and fit precisely onto customized abutment
STRAUMANN
Education
17
Gold abutment – Lab procedures
Complete ceramic veneering
Deliver final restoration to dentist
STRAUMANN
Education
18
Gold abutment - Lab Procedures
Final insertion
Remove the healing abutment or temporary restoration and
thoroughly clean the implant and bridge
Position restoration and check fit
STRAUMANN
Education
20
Gold abutment - Lab Procedures
Final insertion
Tighten to 35 Ncm with SCS screwdriver and torque
ratchet
Close screw access with cotton, sealing compound (i.e.
gutta percha) and composite
Cement single unit crown
STRAUMANN
Education
21