Transcript Hand and Power Tools BONUS BONUS BONUS BONUS BONUS When it is important that the object you are striking not be damaged which tool is the best.

Hand and Power Tools
1
2
3
4
5
BONUS
6
7
8
9
10
BONUS
11
12
13
14
15
BONUS
16
17
18
19
20
BONUS
21
22
23
24
25
BONUS
When it is important that the object you
are striking not be damaged which tool
is the best one to use?
A.
B.
C.
D.
Bell faced Hammer
Claw Hammer
Sledge Hammer
Mallet
A
B
C
D
Which of the following wrenches is
adjustable?
A. Striking Wrench
B. Box-end Wrench
C. Pipe Wrench
D. Combination Wrench
A
B
C
D
A crosshead screw is tightened by using
which of the following?
A. Allen Wrench
B. Torx Screwdriver
C. Phillips Head Screwdriver
D. Robertson Head Screwdriver
A
B
C
D
You should discard a clamp with a
________.
A. Ridged Jaw
B. Sliding Jaw
C. Swivel Jaw that turns freely
D. Bent Frame
A
B
C
D
Which of the following should you wear
when you use a nail puller or a ripping
bar?
A. Safety Glasses, Hard Hat, Ear Plugs
B. Hard Hat, Safety Glasses, Gloves
C. Safety Glasses, gloves, Resporator
D. Hard Hat, Ear Plugs, Gloves
A
B
C
D
What type of hammer should
never be used in the
construction industry?
A.
B.
C.
D.
Sledge Hammer
Ball Peen Hammer
Cast Head Hammer
Claw Hammer
A
B
C
D
Safe use of a wrench requires you to do
which of the following?
A. Push it away from you.
B. Pull it towards you.
C. Use an extension.
D. Use the shortest handle available.
A
B
C
D
Which one of these should be
sharpened on an oil stone?
A. Punch
B. Chisel
C. File
D. Screwdriver
A
B
C
D
Which tool would you use to drive a
stake into the ground 18” to 24”?
A. Claw Hammer
B. Sledge Hammer
C. Wooden Mallet
D. Slag Hammer
A
B
C
D
Which of the following would you
use to cut heavy gauge wire?
A. Lineman's Pliers
B. Needle-nose Pliers
C. Channellock Pliers
D. Slip-joint Pliers
A
B
C
D
Use this to maintain a saw blade
properly.
A. Sand paper
B. Grinder
C. Emery cloth
D. A file
A
B
C
D
A.
B.
C.
D.
A saber saw will cut more
smoothly if you use this.
Oil
Water
Grease
Beeswax
A
B
C
D
Proper maintenance of pliers
requires you to do which of the
following?
A. Wipe with a soft cloth
B. Use Grease
C. Oil the joints
D. Wash with Water
A
B
C
D
Which of the following is used to
measure vertical distances?
A. Steel Rule
B. Micrometer
C. Measuring Tape
D. Wooden Folding Rule
A
B
C
D
A _______ Square is used to
mark many different angles.
A. Try
B. Carpenter’s
C. Rafter Angle
D. Framing
A
B
C
D
Which of the following bits are
used to drill in wood?
A.
B.
C.
D.
Auger
Carbide
Shank
Masonry
A
B
C
D
A.
B.
C.
D.
When is a surface plumb?
Centered between two objects
Exactly horizontal
Exactly vertical
At a 45 degree angle
A
B
C
D
When cutting with a circular saw you
should always cut on this side of
the line.
A. Top
B. Bottom
C. Finish side
D. Waste or unused side
A
B
C
D
A.
B.
C.
D.
This is essential to the safe
operation of an electric drill.
Keyless chuck
Trigger lock
GFCI outlet
Chuck key holder
A
B
C
D
You should stand at this point
when using a circular saw.
A. Directly behind the work
B. To one side of the work
C. Directly in front of the cut
D. Directly over the work.
A
B
C
D
ALWAYS do this when working on
any power tool.
A. Disconnect power
B. Set the trigger lock
C. Remove the blade
D. Apply grease
A
B
C
D
To extend the life of a hand held
band saw blade you should do
which of the following?
A. Operate at low speed
B. Operate at high speed
C. Vary the speed
D. Operate at medium speed
A
B
C
D
Which of these grinders is used to
smooth a damaged chisel
head?
A. End
B. Angle
C. Bench
D. Detail
A
B
C
D
Air pressure is used to power this
kind of tool.
A. Hydraulic
B. Pneumatic
C. Aerodynamic
D. Electromagnetic
A
B
C
D
A.
B.
C.
D.
The first step for operating an
electromagnetic drill is_____.
Put the power to the On position
Put the electromagnetic switch
to the On position
Set the depth gauge
Turn the switch OFF
A
B
C
D
A.
B.
C.
D.
What do you do if a nail gun
leaves the nail head above the
surface.
Lower the air pressure
Raise the air pressure
Lower the nail size
Raise the nail size
A
B
C
D
BONUS
When does a belt sander work
best?
A. When it is stationary on the
surface to be sanded
B. Started at low speed
C. When used with high grit paper
D. Running at full speed before
you touch the surface
A
B
C
D
BONUS
A cracked grinder wheel will do
which of the following?
A. Ring clearly
B. Make a dull thud
C. Splinter
D. Develop visible cracks.
A
B
C
D
BONUS
How far away should you keep
any part of your body from a
cutting tool?
A. 1’
B. 6’
C. 3”
D. 6”
A
B
C
D
BONUS
Dust from an electric sander is
_______.
A. Harmless
B. Explosive
C. Will damage the sander
D. Completely removed from the
collection system
A
B
C
D
BONUS
Which of the following is used to
break brick or concrete?
A. pavement breaker
B. Hammer drill
C. Pneumatic drill
D. Hydraulic jack
A
B
C
D
INCORRECT
CORRECT