Transcript 営業SE研修：システム提案 LAN編（IPMLT）

Legacy-GW Features
Rev1.4 24 Jan., 2013
Over view
2
Over view
1.Use NCP/TDE（TDA）as a legacy GW by stacking connection
with NS1000.
2.NCP/TDE(TDA) connect with NS by stacking card working
as part of One-look network.
3
Over view
Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE)
STACK-M card
Site #1
NS1000 as stacking Master Unit
Slave Units
Master for
One-look
Site #2
Site #3
Stacking Slave
NCP500
NCP1000
LAN
Stacking Slave
Stacking Slave
STACK-S
card
Site #4
：
：
Stacking Slave
Proprietary cable for stacking connection
The length of the cable：2M
(Dedicate cable for these Stacking card)
4
Over view
New card
Symbol
Model
Name
Description
STACK-M
KX-NS0130
Stacking Master Card
- Interface card for Legacy-GW
- Proprietary Interface x 2
ports
Symbol
Model
Name
Description
STACK-S
(NCP)
STACK-S
(TDE/TDA)
Remark
Remark
KX-NS0131
Stacking EXP Card for
NCP
Legacy-GW Control Unit for
NCP
with Stacking
Cable
KX-NS0132
Stacking EXP Card for
TDE/TDA
Legacy-GW Control Unit for
TDE/TDA
with Stacking
Cable
5
Condition
6
Condition 1
STACK-M card
Stacking Slave #1
1.MPR of NCP has to be removed to
install Stack-S card.
This means Virtual card on NCP
is not supported.
All of IP terminal has to connect to
NS1000.
2.Type of GW has to be same for
each NS1000.
Category1: NCP500 /NCP1000
Stacking Slave #2
Category2: TDE100/200, TDA100/200
Category3: TDE600/620, TDA600/620
*If the type of cabinet is mixed then
STACK-S
card
2nd one will not be worked.
3.Max 2 GW for each NS. Max 8 for
entire One-look network.
4.TDA15/30/50/100D is not
supported.
5. AK is not required to use Legacy GW.
7
Condition 2
In case of TDE600 each cabinet count as 1 GW and connection to NS has to be done
by Stack-S card.
Bus card in TDE600 and TDE620 has to be removed.
NS1000
NS1000
NS1000
TDE620
TDE620
TDE600
TDE600
TDE620
TDE600
OR
OR
8
Condition 3
Which Optional card can not be used at Legacy GW?
Symbol
Model
Description
RMT
TDA0196
Analogue Modem for Remote Maintenance
MEC
TDA0105/
TDE0105
Memory Expansion Card
DSP4
NCP1104
VoIP channel card 4ch
DSP16
TDE0110
VoIP channel card 16ch
DSP64
TDE0111
VoIP channel card 64ch
CTI-LINK
TDA0410
CTI Link Card
IP-EXT16
TDA0470
16-Channnel VoIP Extension Card
3) IP-GW, IP-EXT
IP-GW4E
TDA0484
4-Channnel VoIP Gateway Card
4) MSG
IP-GW16
TDA0490
16-Channnel VoIP Gateway Card
are not supported.
IP GW4
TDA0480
4 Channel VoIP Gateway Card
MSG4
TDA0191
4-Channel Message Card
ESVM2
TDA0192
2-Channel Simplified Voice Message Card
ESVM4
TDA0194
4-Channel Simplified Voice Message Card
CLCOT8
TDA1180
8-Port Analogue Trunk Base Card w/ Caller ID
CLCOT8E
TDA1186
8-Port Analogue Trunk Daughter Card w/ Caller ID
MCSLC24
TDA1178
24-Port Single Line Telephone Card
MCSLC16
TDA1176
16-Port Single Line Telephone Card
Basically
Optional card
1)on TDE/NCP MPR
2)Support by V5 or later
9
Condition 4
How many CO can be installed in each Legacy GW?
Stand-alone
Stacking system
1NCP500
1NCP1000
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
Trunk(ch)
256
256
256
48
30
0
256
256
256
48
64/64/120/128/160
LCOT
2
0
BRI
8
PRI23
2NCP500
2NCP1000
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
One Look
Networking
128/128/240/256/256
600
256
256
96
600
12/16/96/128/160
24/32/192/256/256
600
0
12/16/96/128/160
24/32/192/256/256
600
23
0
46/46/92/92/115
92/92/184/184/230
600
PRI30
30
0
60/60/120/120/150
120/120/240/240/256
600
T1
0
0
48/48/96/96/120
96/96/192/192/240
600
E1
0
0
60/60/120/120/150
120/120/240/240/256
600
IP
SIP
H.323
Legacy
10
Condition 5
How many EXT can be installed in each Legacy GW?
Standalone
SIP Phone
KX-UT series
640
640
256
640
640
640
1NCP
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
640
640
256
640
640
640
S-PS(SIP based DECT)
255
255
Extension(ch)
IP
IP-PT
SIP
Legacy *1
Stacking system
2NCP
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
One Look
Networkin
g
1000
1000
1000
1000
1000
1000
255
2
0
44/160/256/304
88/320/512/608
1000
SLT
2
0
36/96/128/240
72/192/256/480
1000
DPT
0
0
40/128/256/256
80/256/512/512
1000
11
Condition 6
How many other devices can be installed in each Legacy GW?
Stand-alone
Stacking system
1NCP
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
CS (pcs)
DPT-CS (2ch)
DPT-CS (8ch)
IP-CS
SIP-CS
PS(DECT)(pcs)
VM
Built-in UM (ch)
TVA/TVM (ch)
64
0
0
64 *2
64 *3
512
24
0
0
0
0
64
11/32/32/32
5/16/16/16
64 *2
64 *3
512
2NCP
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
22/64/64/64
10/32/32/32
24
48 (24ch x2)
One Look
Networking
128
128
64
128 *2
128 *3
512
24ch x16
24ch x8
*2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs.
*3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.
12
Condition 7
• AK on NCP/TDE can’t be transferred to NS MPR.
• In case of TDA100/200 and TDE100/200
OPB3 card with ECHO16 must be installed in only SLOT1.
- Other than OPB3 card allows to install in any SLOT.
- OPB3 card with sub-card except for ECHO16 allows
installing in any SLOT.
• HGT100, NT400 can’t be connected to NS MPR.
13
How to work?
14
How to work?
Installation
• Both Stack-M and Stack-S card is non hot swappable.
• Each cabinet can be power on without any order.
• Initial Legacy-GW installation, all card will be initialized.
• The optional service cards is hot swappable.
• TVM can be installed as VM system for entire One-look.
• CS can be installed at both NS(NCP0158) and Legacy-GW
(TDA0141/142/155/156/158). PS can Hand over between
these CS to CS(NCP0158, TDA0141/142/155/156/158).
15
How to work?
Wireless
•Hand over between NS to Legacy GW and Legacy GW to
Legacy GW is available.
LAN
IP-CS
CS
IP-CS(NCP0158)
CS(TDA0141/142/155/156/158)
PS
CS
CS
•If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.
16
How to work?
Start up
LED Status
“Stack-M” LED
Green On : Normal working condition
Off: Error( Not Working)
“Stack-S” LED
Green On : INS
Red On : Fault
Red Flash: OUS
Legacy GW
“RUN” LED
Green Off :Power off
On
: Running as GW
Slow Flash: While start up
“ALARM” LED
Red Off : No present error
On : Present Error
17
How to work?
Maintenance
All below service for Legacy-GW is supported through
NS1000 cabinet.
• Programming
• Firmware update
• Error log, Syslog
• SNMP information
• SMDR
18
Programming
19
Programming
Programming at NS1000
Button to switch Physical-Virtual-LegacyGW1-LegacyGW2
Stack S connect to “1” on
Stack M consider as “GW1”
Each Optional Card can be selected and installed.
20
Programming
Programming at NS1000
LPR Software :Software can be download through NS1000
LPR Software name same as existing models
LPR Software for STACK-S card “PSTKS” is new!
21
Programming
Programming at NS1000
Programming items related to Legacy GW support.
Related to VM.
Related to DSS.
Port Property
22
Appendix
23
Appendix
Supported optional card
24
Appendix
Supported optional card
25
Appendix
Supported optional card
26
END
27
Modification
20120827-01 LegacyGW_Rev1_27Aug2012Mar.ppt
- 1st release
20120905-02 LegacyGW_Rev1_1_5Sep2012Mar.ppt
- Edit slide #11 revise number of legacy EXT and DPT.
- Add slide #12
20121031-03 LegacyGW_Rev1_2_31Oct2012Mar.ppt
- Add comment for slide #7 “No AK required”
- Add additional sample for slide #8
- Add comment for slide #9 “Basic idea”
- Add comment for #13 about HGT100 and NT400
- Add remark for #16
20121108-04 LegacyGW_Rev1_3_8Nov2012Mar.ppt
- correct slide #8 600-620 twice to 600-620 and 620-620
20130124-05 LegacyGW_Rev1_4_24Jan2013Mar.ppt
- correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW
28