Transcript Welcome to FILO 1.0 coreboot’s smart OS loader Drives found: hda: LBA 40GB: WDC WD400BB-23FJA0 hdc: ATAPI: CD-ROM Drive/F5D searching for hda1:/filo.conf*******found. Your computer is.

Welcome to FILO 1.0 coreboot’s smart OS loader
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
searching for hda1:/filo.conf*******found.
Your computer is pre-configured to auto boot
the specified parameters in filo.conf:
Linux on Hard Drive
hda1:/vmlinuz initrd=hda1:/root.gz
root=/dev/ram
You have 5 seconds to interrupt this auto
boot and enter the Settings Menu.
****
FILO 1.0
Settings Menu
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
1.
2.
3.
4.
5.
Boot to another OS listed in filo.conf
Edit your filo.conf file.
Change boot method
Manually boot
Configure a command line for FILO to use
(good for single OS systems)
6. Tell FILO where your filo.conf file is
located on your hard drive (good for multi
OS systems)
7. Set auto boot time out
Option:___
FILO 1.0
Option 1. Boot to another OS listed in filo.conf
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
OS’s listed in filo.conf
1. Linux on Hard Drive
hda1:/vmlinuz initrd=hda1:/root.gz
root=/dev/ram
2. Linux on CD-ROM
hdc:/vmlinuz initrd=hda1:/root.gz
root=/dev/ram
Option:___
FILO 1.0
Option 2. Edit filo.conf
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
Editing hda1:/filo.conf
Edit your boot parameters below:
Linux on Hard Drive
hda1:/vmlinuz initrd=hda1:/root.gz root=/dev/ram
Linux on CD-ROM
hdc:/vmlinuz initrd=hda1:/root.gz root=/dev/ram
Do you want to save this to filo.conf(Y/N)?___
FILO 1.0
Option 3. Change boot method
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
1. Manually boot
2. Boot to command line for FILO to use (must
configure option 3 from the Settings Menu)
3. Tell FILO where your filo.conf file is
located on your hard drive (must configure
option 4 from the Settings Menu)
Option:___
Do you want to save this to CMOS(Y/N)?___
FILO 1.0
Option 4. Manually boot
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
Enter your boot parameters below and then press
<ENTER>:
boot: hda1:/vmlinuz initrd=hda1:/root.gz
root=/dev/ram
FILO 1.0
Option 5. Configure a command line for FILO to use
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
Enter a command line in FILO format:
hda1:/vmlinuz initrd=hda1:/root.gz root=/dev/ram
Do you want to save this to CMOS(Y/N)?___
FILO 1.0
Option 6. Tell FILO where your filo.conf file is
located on your hard drive
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
Enter the path to filo.conf in FILO format:
hda1:/filo.conf
Do you want to save this to CMOS(Y/N)?___
FILO 1.0
Option 7. Set auto boot time out
Drives found:
hda: LBA 40GB: WDC WD400BB-23FJA0
hdc: ATAPI: CD-ROM Drive/F5D
Enter auto boot time out in seconds:___
Do you want to save this to CMOS(Y/N)?___
FILO 1.0
Attempting to boot
Booting ‘hda1:/vmlinuz initrd=hda1:/root.gz
root=/dev/ram’ - success-goodbye