Transcript Legbud Gargula Fitting Instructions

Framed Canopy
Fitting Instructions
• Contents –
• Before you start !!
•
•
•
•
•
•
6- Angled frame fixing brackets
1 x handle pack
6 x self drilling tech screws
3 keys
1x door
6 x coach screws
•
•
•
This door is delivered with a protective film
To the Frame only and should be removed
now if fixing the frame to the back of the
brick opening .
This door is CE Marked and comes with a
Europe wide 2 year warranty , the
warranty is subject to conditions please
see your dealer for terms .
Caution Garage doors Are heavy and we
recommend that this item be installed by
two persons
Do not allow children to assist in the
installation of this product or use the
product un-assisted , garage doors can
inflict severe injury if not used correctly .
Always ensure the door is correctly
adjusted and serviced failure to do so may
invalidate the warranty . This does not
effect your statutory rights .
•
•
•
•
•
Measure
Check measure the door and frame against the brick
opening to ensure the door will fit into the opening and
then open when installed ,
Check the space required inside the garage that the door
will not be impeded by anything in the garage .
•
•
•
•
•
•
•
•
•
•
•
Tools required
Cordless Drill.
8mm socket with drill attachment .
10mm socket with drill attachment .
8mm masonry drill bit
Phillips screwdriver .
10mm socket
10mm ring spanner .
Timber wedges for levelling
Spirit level
Set of Alen keys
•
•
•
•
Fixings not supplied
We recommend 8mm wall plugs (Rawl)
Silicone sealer
Light Oil (3in1)
Installation
This door can be fitted either between the brickwork at the front of the structural opening or behind the brickwork at the back of the structural opening .
If fitting Between the structural opening at the front then fix 3 Angled frame fixing brackets per side as shown below .
Bracket 1 Top .
Bracket 2 Middle
Bracket 3 Bottom
If fitting Behind the structural opening then fix the Angled frame fixing brackets as shown below .
Fix the bottom bracket as low as possible .
All installation methods require the use of 1 x 8mm self
drilling tech screw 1 x flat washer , drive the tech screw
in using a cordless drill with a 8mm socket attachment
and fix securely (careful not to over tighten the screw )
Repeat for the three brackets per side , the head of the
frame is not fixed to the opening .
Offer the door up to the opening (two persons required ) and wedge in to place , use a spirit level to ensure the overall satisfactory look of
the installation and in particular the level of the frame head is correct .
If you twist the door in installation the locking may not operate correctly .
When satisfied with the door position drill an 8mm hole and bolt in the M6 50mm coach screws (rawl plug not supplied). Repeat for all
brackets
There is a red drum to the right at the top and a white drum to the left , the cables wrap around the drum to lift the door , you must ensure
the cables are correctly located the same both sides now , they wrap from the outer to the inner part of the drum .
Now pull the pin that is used to secure the tension during transport , this
can be quite stiff as it holds the spring pressure , work it side to side to
ease it free.
Now fit the handle as shown.
Fit the outer handle to the outside of the door , fit the inner lock and the moulded fixing using an Alan key and tighten
(Caution !! only tighten enough to remove play from handle , over tightening can damage the outer panel )
Open the door fully and oil the side runners and the wheels / cables and top latches . If 4 point locking purchased see
separate sheet and fit now .
Caution !!Check the locking works correctly from the inside by closing the door and opening again , do not do this from
the outside as if adjustment is required you may not be able to open the door again .Although adjusted in the factory the
cables can be disturbed during transport and it is the responsibility of the installer to correct the cables as required .
Adjustment – if the door is opening too slowly or too quickly increase the tension on the spring .Call 0121 749 7977 for
advice .This element should only be performed by competent persons .
Finish the door frame with trim as required .
Locking cables and lifting cables are subject to wear and tear and should be examined regularly , tangling of
cables through poor maintenance / adjustment does not constitute as a manufacturing defect.
Technical helpline 01217497977
Removal .
To remove the door you first must replace the spring
tension holder shown on page 3 . Remove side track
screws and slide out the tracks , undo the spring
holder bracket screws x 4 and lift the entire spring
spring assembly off the locking point/ spring holder
and lower the spring to the mid point of the door .
Ease the door out of the opening .
Every 3 months you must oil
all pivot points with 3 in 1 oil ,
you must check tension of the
door ( open the door and
ensure it holds in place if it
falls contact your dealer or
the helpline for more advice )
Clean the paint finish and
touch up any marks with the
correct Ral colour stick
available from your dealer .
Refer to the door label for
more advice .