Transcript Tools - CR Products

Tools
Unlock the power of the tools
in the Carlisle Tool-Crib
to help you design, install
and tension your belt drives.
Carlisle Tool-Crib
Sheave Gauges - plastic sheave templates
$3.75 each
part numbers: 102495 — RMA & Metric combined gauge
SheaveMaster - laser alignment tool. The SheaveMaster is a
laser tool for fast and accurate alignment of belt drive pulleys.
(part number: 108076-A) $750.00 each
Tension Finder - introducing a new tensioning tool from
Carlisle Power Transmission - a simple, easy and accurate
alternative for tensioning of individual belts or v-bands.
(part number: 108039-A) $24.00 each
Wallboard Display - a popular inventory and display system for
v-belts. Includes 10 boards and 80 wallboard hooks.
(part number: 93899) currently not available
Carlisle Tool-Crib
Tensiometer - single, double and triple stem
belt tension tester.
part numbers: single 102761—
double 105575 —
triple 105576 —
Drive Engineer - drive design software. Contact us on-line
([email protected]) to receive a free copy of Drive Engineer
(€25 value) or call customer service on +44 1327 701030.
Frequency-Finder - allows you to take simple, fast, repeatable
and reliable tension measurements and can be used on virtually any
type of belt.
part number: 109061 —
Belt-Finder - belt measuring device. Find the exact Carlisle
replacement belt instantly.
part number: 93859 —
Sheave Gauges
•
RMA and Metric combined
• Sheave condition and alignment are
vital to V-belt life and performance
• New V-belts should never be installed
without a thorough inspection of the
sheaves
• Use the sheave gauge to accurately
check grooves for wear
• Wear should not exceed 1/32” for
individual V-belts or 1/64”for banded
V-belts
SheaveMaster Laser Alignment
• Laser tool for fast & accurate alignment
• Magnetically mounted tool & 3 targets
• Quickly correct angular, offset and
•
•
•
•
twist misalignment
Only one person is needed
Water, dust and shock proof
Permanently calibrated
Can be used indoors or out
Tension-Finder
• No Measurements
• No Math
• No O-rings
• No Computers
• It’s Practical
• It’s Reusable
• It’s Easy
• It Works!
Wallboard Display/Belt Racks
• Popular inventory and
display system for V-belts
• Includes 10 boards and
80 wallboard hooks
•Plastic board is 36 inches
long, hooks extend 5 3/8”
Spring Loaded Tension Gauges
• Tensioning method based on the fact that
the force required to deflect a given span
length by a given amount is related to the
tension in the belt
• Proper tensioning of V-belts is the single
most important factor necessary for long,
satisfactory operation
• Too little tension will result in slippage,
causing rapid belt and sheave wear
• Too much tension can result in excessive
stress on belts, bearings, and shafts
Drive Engineer
• Windows®-based program
• User friendly
• New drive selection
• Existing drive analysis
• New generation of analysis
software that helps end users
increase their drive efficiency,
drive life and overall knowledge
of belt drives
• Download from our website
www.cptbelts.com or call
customer service 866-773-2926
Frequency-Finder
• Measures the natural frequency
of vibration in the belt span
• Simple, fast, repeatable and
reliable
• Can be used on virtually any
type of belt
• Most precise method
Belt-Finder Measuring Tool
• Find the exact Carlisle
replacement belt instantly
• A quick check shows the top
width and length / part no.
• Check Classical A & B belts,
Durapower or XDV, plus
3VX and 5VX Power-Wedge
www.CarlisleBelts.com
from
www.c-rproducts.com
[email protected]
Tel: +44 1327 701030
Fax: +44 1327 701031