SIP-Based-DECT

Rev1.9 25 Feb., 2013

Table of Contents

1. Overview 2. Specification and Features 3. Air Synchronization 4. Registration 1. Installation Basic Flow 2. CS radio zone design 3. CS/PS Firmware Update 4. Setup CS/PS and NS1000 5. Maintenance of System phone book Appendix - PS Ring Group

-

Air Synchronization

-

Move CS

-

Site Survey (Tool)

-

Site Planning (Tool) - PS function List

2

Chapter 1 Overview

3

1. Overview (Why SIP-Based DECT)

In Expensive Wireless solution with SIP based DECT solution High Quality Voice with Noise reduction Dramatically Reduce Wire installation cost in large service area.

Easy install and maintenance with Firmware Air-download

No separate server or GW is required with NS1000, Offer high-quality Business Communication, with most Reliable DECT Technology.

Radio technology VoIP signaling Number of Handsets Number of CS CS synchronization Handover Spec.

DECT SIP Max. 255 handsets

*1

Max. 128 CS Max. 32 CS/8Air sync group Air synchronization Yes (seamless) Cell Station LAN Cell Station

4

1. Overview (Hand Over) SIP based DECT phone satisfies needs of personnel who want to be always ready to talk to partners or customers anywhere and anytime within their company.

NS1000 Hand Over

5

1. Overview Multi Zone

PS can be reception which is located anywhere.

The whole building becomes the communication zone.

Features and Benefits Office Hallways On-site employees: efficient because it is not necessary to return to the office to make a call.

Hand-over Call receptionists: less trouble because the person to transfer the call to can be anywhere.

Customers: improved CS because there is less time spent waiting to transfer calls.

Meeting Room Storage Suitable Environments Frequent moving about inside the company Retail Store Automotive Dealership Factory

6

1. Overview Move to other System/Location

PS can be moved from original site to the other site.

In this condition, the PS must be resisted to other unit also PS can be resisted up to 4 different Cell Station (Need to regist NS1000 also) Master Units Slave Units IP Move with PS to other site

7

Chapter 2 Specification and Features

8

2. Specification and Features

Portable Station (Standard Model)

KX-UDT111

- High quality wideband voice - Noise reduction -Full-duplex hands free -Air-download of firmware - Headset jack (2.5mm plug) - Vibration - Up to 500 personal phonebook

US/CANADA Model EU Model 9

2. Specification and Features

Portable Station (Slim & Light Model)

KX-UDT121

US/CANADA EU Model *Future - High quality wideband voice - Noise reduction -Full-duplex hands free - Air-download of firmware - Headset jack (2.5mm plug) *LCD back light off and Bluetooth is not in use.

- Vibration - Up to 500 personal phonebook - Bluetooth

（

Version 2.0, Class 2

）

(Headset/Phonebook transfer

） 10

2. Specification and Features

Portable Station (Taught Model) - High quality wideband voice

KX-UDT131

- Noise reduction -Full-duplex hands free *Future - Air-download of firmware

-

Vibration

-

Against Hazard LevelIP65 (IEC529) - Up to 500 personal phonebook *LCD back light off and Bluetooth is not in use.

- Bluetooth

（

Version 2.0, Class 2

）

(Headset/Phonebook transfer

）

EU Model US/CANADA

11

2. Specification and Features

Cell Station

KX-UDS124

- Web interface for set up - Air-download of firmware - Max PS registration : Up to 255 per CS and System *Future - The number of Cell Station for a system : Up to 64 or 128 (One Look networking) (32 per air sync group/Max 8 Air sync group per one Unit, total max 128 Air Sync group on One-Look networking ) - PoE or optional AC adaptor(KX-A239)

12

2. Specification and Features

PS Detail Specification LCD LCD Backlit Bluetooth Vibration Quick Charge Talk Time Stand bay time DECT Encryption Soft Key Size (HxWxD) Weight Battery KX-UDT111 1.8”, 65,000-color TFT display Yes No Yes No

（

10Hours) 12h (Narrow band) 9h (Wide band) 200h Yes 3 146.3x48x25.4 mm 115g AAA-Ni-MH 2 cell Enclose AC Adaptor, Charger Belt Clip and Holder KX-UDT121 1.8”, 65,000-color TFT display Yes Built in Yes Yes (3 Hours) 14h (Narrow band) 11h (Wide band) 200h Yes 3 127.5x48.5x18 mm Battery

：

90g Li-ion 3.7V 700mAh AC Adaptor, Charger Belt Clip and Holder KX-UDT131 1.8”, 65,000-color TFT display Yes Built in Yes Yes (3 Hours) 14h (Narrow band) 11h (Wide band) 200h Yes 3 152 X 55 X 23mm 150g Battery

：

Li-ion 3.7V 700mAh AC Adaptor, Charger Belt Clip and Holder

13

2. Specification and Features

CS Detail Specification Model No.

Type Max. simultaneous calls Wideband Audio Power supply CODEC (IP) LAN port Firmware upgrade DECT Encryption Seamless Handover Size Weight KX-UDS124 4ch wideband audio CS 4 Yes PoE (IEEE 802.3af) AC adaptor

（

optional

）

G.722, G.711, G.729a

10 base-T / 100 base-TX Yes Yes Yes 190

×

133.9

×

39.3 mm 330g (Include wall mount adaptor)

14

2. Specification and Features

CS Detail Specification LED indication on CS LED Display OFF Green ON Slow Green Flashing Moderate Green Flashing Red ON Slow Red Flashing Moderate Red Flashing Amber ON Slow Amber Flashing Moderate Amber Flashing Moderate (Red ->Green->Yellow) Flashing Red and Green alternate flashing Status Power Off / CS software download Standby (no active calls) Talk (active calls) Busy (All talk path are occupied) Fault (FLASH ROM Can not access etc.) OUS or Start up (data link establishment



air synchronization) Start up (power on



data link establishment) Standby: unstable synchronization (no active calls) Talk: unstable synchronization (active calls) Busy: unstable synchronization * Detect Rest Switch on Power On Status (Open CS-Web port) Master-CS indication on Site survey mode. LED indication for Slave CS on Site survey mode is follow.

- Green Flashing :Synchronizing - Amber Flashing :Weak radio signaling level - Red Flashing : Out of area

Note) LED flashing patterns are as follows: Slow Flashing: 60 times per minute

Moderate Flashing: 120 t60INT-2 Green Flashing/per minute

15

2. Specification and Features

CS Detail Specification Error Indication and how to recover

16

2. Specification and Features

System Capacity System Capacity Extension IP PS(UDS1XX) Legacy SLT DPT CS (pcs) CS-IF (4/8) Card DPT-CS IP-CS PS SIP-CS(UDS124) (WT/TCA) StandAlone 640 640 255 2 2 0 64 0 0 64 64 512 Main 0 0 0 0 0 Stacking system One Slave 640 640 Two Slave 255 36/96/128/240(*1) 36/96/128/160(*1) 36/96/128/160(*1) 64 4 11/32/32/32(*1) 64 64 512 72/192/256/480 (*2) 72/192/256/320(*2) 72/192/256/320(*2) 8 22/64/64/64(*2) Networking 1000 1000 255 1000 1000 1000 128 16 128 128 128 512 *1: MM/NN/XX/YY means One NCP/One TDE100-TDA100/OneTDE200-TA200/OneTDE600-TDA600 *2: mm/nn/xx/yy means Two NCP/Two TDE100-TDA100/TwoTDE200-TA200/TwoTDE600-TDA600

17

2. Specification and Features (Cover Area)

CS Coverage Area for Establishing Conversation Using PSs A B Gray Zone: Conversation will be intermittent C A Coverage Area: (About 50m to 60m) B Good Coverage Area: (About 30m to 40m) Good sound quality can be maintained.

C Out of Service: Cannot make/receive calls.

18

2. Specification and Features (Easy Installation)

Site Survey for Air Synchronization SIP-CSs have ability of site survey to check radio signal strength.

By the LED on SIP-CS, you can check the radio signal 1. Set Temporally master CS for site survey as planned - Power on CS with pressing rest SW . - Release Reset switch while LED flashes (Green/Red/Amber) - Press Rest Switch one second once again (Green and Red LED start flashing) 2. Turn on Power of slave CS and locate it, then check LED on CS.

3. Move Slave until LED on Slave CS goes green See Appendix in more detail

19

2. Specification and Features (Easy Installation)

Site Survey for S-PS Service Area The PS has a PS AREA CHECK ability User can confirm CS cover area easily by this function 1. Power ON CS and set Maintenance mode 2. Change PS to PS AREA CHECK mode 3. Make call from PS to PS See Appendix in more Detail

20

2. Specification and Features

Wideband Audio Support Clear & Natural voice by Wideband Audio.

Multi Handsets and Multi-Cell supported.

Better Receiving Frequency Response Human voice Range Enhance Narrow Band (G.711) Wide Band (G.722) Enhance Enhance the Lower frequency with small receiver Enhance the High frequency receiver by aperture rate of the previous model (Panasonic PBX terminal) UDT111 UDT121 U P aperture rate 4.3 % aperture rate 35 % aperture rate 24.5 %

21

2. Specification and Features (Pattern1)

Noise Reduction features Can configure TX/RX noise reduction to ON/OFF during standby and talk (Default : OFF).

TX : Noise Reduction for Sending Signal Detect and reduce noise part from the transmission voice Noise reduction

Noise sound Voice Noise

RX : Listening Enhancement for Receiving Signal Dynamic receiving volume control according to acoustic ambient noise characteristics

Noise sound

High noise Low noise High volume Normal volume Waiting Demo Voice file ***

22

2. Specification and Features (Pattern1)

Noise Reduction features

Strong against the multipath environment by the enhanced precision of error detection and new voice processing technology.

Multipath Fading Ex) cubicle farm, concrete building occurrence multipath by direct/ reflected/diffracted wave, etc PS Direct wave CS

Panasonic Technology

The fading occurs when moving the place where the electric wave is strengthened or weakened each other under multipath environment. Example

Error Less Received RF power at cordless handset under multipath environment.

High Low Freq

Error

[Time]

Old

Voice waveform Proprietary Process

Reflected wave Diffracted wave New

Advanced error correction makes stable communication.

23

2. Specification and Features

KX-UDT111 Appearance Large Ringer / Charge LED

CONCAVE

Receiver

Enhance aperture rate

aperture rate 4.3% (previous model) Strap hole1 Belt clip hole

-

Shape to avoid operation mistake in the pocket - Shape to protect keys

-

Concave shape and rippled keys for easy access to keys Headset Connection Key backlit aperture rate 35.0% (UDT111) 1.8inch Color LCD with backlit 3 Soft keys Microphone Navigation key Wall mountable charger Strap hole2

24

2. Specification and Features

KX-UDT121 Appearance Ringer / Charge LED

Pocket size

Receiver

（

48.5

ｍｍ）

Strap hole1 Belt clip hole Headset Connection 1.8inch

Color LCD with backlit 3 Soft keys Navigation key

（

127.5

ｍｍ） （

18

ｍｍ） （

90g

）

Enhance aperture rate

aperture rate 4.3% (previous model) aperture rate 24.5% (UDT121)

Plating Grill

Section keys Wall mountable charger Key backlit Strap hole2 Microphone

25

Chapter 3 Air Synchronization

26

3. Air Synchronization

Air Synchronization To activate Handover through CS, all CS must be synchronized.

CSs are synchronized by using “Air Synchronization” for same air Sync. group After CS synchronized with other CS, Handover is available.

LAN i/f L2 SW Handover is available Air Synchronisation CS (Master) Handover is not Available Air Synchronisation CS (Slave) Handover is not Available Synchronised By Air Synchronisation CS (Slave)

27

3. Air Synchronization

CS Coverage Area for Air Synchronization between CSs C B A Gray Zone: Conversation will be intermittent C You must not install SIP-CS without site survey.

A Coverage Area: Radio signal strength level is between “03” (about 50m to 60m) and “14” (about 20m to 30m).

B Good Coverage Area: Radio signal strength level is between “05” (about 40m to 50m) and “14” (about 20m to 30m).

Good synchronisation quality can be maintained.

C Out of Service: 0m to 3m or the radio signal strength level is “00 to 02”.

Cannot be synchronized.

28

Chapter 4 Registration

29

4. Registration

Step for DECT System Installation Following is Step for SIP based DECT system registration 1) Instauration Basic Flow 2) CS Radio Zone Setting (Site Survey) Step0: Initialing CS Step1: Site Planning Step2: Site Survey Step3: CS Registration into Master CS

（

By CS-web) Step4: TreeSurvey 3) Firmware UP date Step1: Local firm Update 4) Set up CS/PS and NS1000 Step1:Virtual Extension (UT) Install Step2:Step up Terminal Type Step3: Entry CS/PS name and FF-Key Step4: Entry CS and PS extension Number)

30

4. Registration

Step for DECT System Installation Continue 4) Set up CS/PS and NS1000 Step5: Set up Master CS Step6: Set up System information URL Step7: PS registration Step8: Set up Slave CS Step9: Set up Master CS of other Air sync group Step10: Set up Slave/Master CS to NS1000 (For Ring group) 5) Set up CS/PS and NS1000

31

4.1. Installation Basic Flow

Basic Flow how to set up CS/PS and regist to NS1000 1. CS radio zone design (Site Survey) 1-1. Site Planning 1-2. Site Survey 1-3. CS Registration into Master CS

（

By CS-web

）

1-4. Tree Survey 2. Firmware Update 2-1. Manual Update 3. Setup CS/PS and NS1000 3-1. NS1000 setting by Web-MC 3-2. Super Master CS setting by CS-Web 3-3. PS registration 4. Maintenance of System phone book 5. PS Ring group setting (see Appendix)

32

4.2. CS Radio Zone setting

Step0: Initialize CS for Before Registration Before CS/PS registration, following process must be done 1. Depress RESET Switch while CS is power on

（

See Note

）

1. Initialize CS 2. Keep pressing RESET Switch 10 sec. 2. Open CS-Web interface And wait around 60sec until LED turn on red When you use CS very first time, you do not need to initialize Note

：

You need wait until LED on the CS will start blinking RED or Stay Red when you initialize CS See next page how to initialize CS by Web 1.

2.

Depress RESET Switch and turn on CS power Keep pressing RESET until LED blink amber /red/green

33

4.2. CS Radio Zone setting

Step0: Initialize CS by CS-Web You can initialize CS by CS-Web interface CS-Web LOGIN CS Default Web Address (192.168.0.241) For CS and PS registration, need to set up Super Master CS 1) Open CS-Web (See previous page) 2) Access CS-Web (Default Web address is 192.168.0.241) 3) Go to Maintenance menu then proceed Factory Reset 4) Then CS will be initialized and LED on CS will start RED blinking Note: *1 To enable CS-Web function, need to proceed power on with reset SW (See Page 28) Login/Password : For Installer instoperatoruserid/instpass, For Customer admin/adminpass

34

4.2. CS Radio Zone setting

Step1: Site Planning Plan the CS position by using Site planning tool - Site planning tool (Excel) 2. Plan & Check CS position Local PC PBX Support Page of CS-Web 1. Down Load 2. Determine size scale Import site map data

（

jpg format) 1) Download Site planning tool (Excel) from PBX Support Page of CS Web Site 2) After you Import site map data to this tool and determine the size scale, you can plan the CS position and check the radio range of CS. (simulate for CS positioning) Note: Please refer Appendix more in detail

35

4.2. CS Radio Zone setting

Step2:Site Survey (1/2) Locate CS as temporarily position by using LED indication Slave 1) Keep Pressing SW and turn on the CS.

2) Release the SW button and depress it again.

⇒

Sync Master mode for Site survey starts.

SyncMaster mode Slave Slave Slave 3) Other CS(s) synchronize to Sync Master CS automatically 4) Check other CS’s LED * Confirm the CS radio status at planning position 5) Change position until being Green LED Slave Change Position 6) Depress the SW button again. (return to Slave) LED LED

■ ■ ■ Green OK Amber NG (poor) Red NG (out of range) 36

4.2. CS Radio Zone setting

Step2:Site Survey (2/2) Following shows Site Survey status indication and status 1. Change to Survey Mode Case 1: Keep Pressing reset SW and turn on the CS.(Master Mote) Release Rest SW And depress again Power on CS with Pressing reset SW Moderate Red Flashing Case 2: Turn on the CS normally. (Slave Mode) Survey Mode2 Power on CS Moderate Red Flashing Survey Mode1 Red and Green Alternate Flashing Note

：

CS must be Fixed IP Mode Ex) 192.168.0.241

CS will enter site survey mode automatically when receives signal from Master CS 2. How to Return Normal Mode from Survey mode Either press Reset SW more than 10 sec, or Power Off CS then Power on CS with pressing Rest SW then change to Fix IP mode then restart CS

37

4.2. CS Radio Zone setting

Step3:CS registration in to Master CS CS Registration into Master CS by CS-Web Slave Slave 1.

CS-Web 2.

Super Master

1.

3.

Slave 4.

3.

Slave 1.

2.

3.

Change “CS Class” from “Slave” to “Master” via CS-Web.

Push “Start CS Registration” button in CS Management screen.

CS(s) that is registered in Super Master are listed up.

38

4.2. CS Radio Zone setting

Step4:Tree Survey Tree Survey (Auto Air Synchronization) by Super Master CS-Web or PC Tool 1) Push “Start Tree Survey” button via CSWeb.

2) System executes auto air synchronization and calculate Tree structure.

3) Push “Apply” button.

CS-Web Web user interface (Web application) - For small system - No installation needed 1.

3.

Super Master . Auto Air Synchronization Slave2 Slave1 CS-MT (SIP CS Management Tool) - For mid and large system - Installation is necessary Slave3 Slave4 Slave5 Note: In case that # of CS are up to 9, PC tool needs to be used for tree-survey.

39

4. 3 Firmware Update

Step1:Update firmware by CS-Web You can perform the firmware update manually using CS Web programming. After the firmware is uploaded to the Super Master CS, the Super Master CS distributes the firmware to all other SIP-CSs automatically.

Upload new firmware Deliver to all CS CS-Web 2 1.

3 4 1. Get in to [Firmware Update]

.

2.

Select

[Direct]

for

[Update Mode]

.

3.

Select updated firmware

4.

Click

[All Update Firmware]

.

Note: You must update CS firmware to V01.200 or later when you use CS under NS1000

40

4. 4 Set up CS/PS and NS1000

Step1:Vitrula Extension (UT) install Click [Setup]



select [PBX Configuration] – [1.Configration] – [1.Slot]



[Virtual] – [V-UTEXT32]

41

4. 4 Set up CS/PS and NS1000

Step2: Set up Terminal Type Set up CS or PS type of Telephone type in Port Property as Master CS/SIP-CS or S-PS Click [Set-up] - [1.Configlation] - [1. Slot] – [Select Target V-UTEXT32] – [Port property] Note: 1. Telephone Type Setting is Master CS: Super master CS which is Master CS of Air Sync Group #1 SIP-CS : Master CS of Air Sync Group 2 to 8 and or all slave CS S-PS : PS 2. Only one Master CS can be set per one Unit 3. Do not need to set UP SIP-CS if customer does not need to set up PS-Ringing (ICD-Group Function)

42

4. 4 Set up CS/PS and NS1000

Step3: Entry CS/PS name and FF-Key 1.

Enter Name of PS and Extension number Click [Set-up] - [1.Configlation] - [1. Slot] – [Select Target V-UTEXT32] – [Port property] Enter PS Name 2. Enter FF-Key of PS Click [Set-up] - [4. Extension] - [1.Wired Extension] - [4. Flexible Button] – [Target PS ] Enter FF-Key Code Can be set these Functions Note: Set up PS related programming by wired extension setting if needed

43

4. 4 Set up CS/PS and NS1000

Step4: Entry CS and PS extension Number 1.

Enter Name of CS and Extension number Click [Set-up] - [1.Configlation] - [1. Slot] – [Select Target V-UTEXT32] – [Port property] Note: 1. For PS registration, need to assign Super Master CS in Virtual UT extension card But, It will not need AK (Capacity of UT-Extension) for Master CS but need AK for PS

44

4. 4 Set up CS/PS and NS1000

Step5: Set up Master CS CS-Web LOGIN Super Master CS Default Web Address (192.168.0.241) For CS and PS registration, need to set up Super Master CS 1) Login CS-Web (192.168.0.241 as a default) In default setting, CS-Web site is set as 192.168.0.241

2) Set up own IP Address In default setting, CS is defined as DHCP mode. If no DHCP server, need to set up own IP address. Master CS 3) Set CS mode as Mater CS mode as Master CS . After IP Address, CS will restart automatically. Better select Static mode on In default, CS mode is set as Slave CS, so need to set CS After set Master CS, CS will restart automatically Note: *1 To enable CS-Web function, need to proceed power on with reset SW (See Page 28) Login/Password : For Installer instoperatoruserid/instpass, For Customer admin/adminpass

45

4. 4 Set up CS/PS and NS1000

Step6: Set up System information URL (in Master CS) In order to download configuration file from NS1000, URL information of Super Master CS for getting the file in NS1000 has to be set by CS-Web.

1) Set following URL into System File URL http://192.168.0.101:7580/utdownload/System.cfg

NS1000 IP address Port # Then, Click All Save.

After set up URL, CS will restart automatically.

Note: At this point, configuration data is downloaded into Super Master CS and registrated to NS1000 automatically even if registration mode is [manual] mode in NS1000

Do not enter any other field

46

4. 4 Set up CS/PS and NS1000

Step7: PS Registration CS-Web LOGIN Regist Super Master CS PS PS has to be registered into Super Master CS by CS-Web as follows: 1) Login CS-Web 2) Select menu of PS Registration.

3) Click Start PS Registration.

4) Select Available PS and move to Selected PS by “>” button.

5) Click Next.

6) Set PS to registration mode and register that to neighbor CS.

*registration mode = push button on PS.

Note: 1. Extension Number is downloaded from NS 1000 automatically, and also when change PS extension number by Web-MC of NS1000, the modification data is also down loaded automatically 2. After regist PS to CS, CS-Web will be closed. After Close CS-Web, can open Web Port by PS setting

Caution: Firmware up process may execute after complete PS registration, during this process you can not de-registration and also do not power down PS , until complete Firmware version up.

47

4. 4 Set up CS/PS and NS1000

Step8: Set up Slave CS CS-Web of Slave CS CS-Web LOGIN LOGIN Regist Super Master CS Slave CS Slave CS can regist to Super Master CS. Just Set up IP address of Master CS (*) Then proceed CS registration by Super Master CS Set up Slave CS IP address Note: If System Mode is set up as DHCP enable, do not need to set up Own IP-Address Set up Master IP address * CS-Web of Super Master CS Start CS registration in Super Master CS

48

4. 4 Set up CS/PS and NS1000

Step9: Set up Master CS of other Air sync group CS-Web of Master CS CS-Web LOGIN LOGIN Regist Set up Master CS IP address Super Master CS Master CS Master CS can regist to Super Master CS address and Super Master IP address * Just Set up own IP And need to proceed CS registration by Super Master CS Set up Super Master IP address * CS-Web of Super Master CS Note: If System Mode is set up as DHCP enable, do not need to set up Own IP-Address When set up different Air Sync Group (Not 1), then need to set up Master IP Address

When change any Air setting value, the CS will be restarted automatically

Start CS registration in Super Master CS

49

4. 4 Set up CS/PS and NS1000

Step10: Set up Slave/Master CS to NS1000 (For Ring group) CS-Web LOGIN Regist Super Master CS Slave CS When user want to use PS-RING group by NS1000 ICD Group function , Must regist Master CS and Slave CS to NS 1000 as follow 1) Set UP Telephone Type as SIP-CS and Extension Number in Web-MC 2) Set up Extension number of Master CS/Slave CS in CS-Web as same as NS1000 Data 3) Set up Password (1234 as default) in CS-Web WEB-MC UT-EXT32 Port property

50

4.5 Phone book registration

Download System Speed Dial data to PS Phone Book When System Speed dial of NS1000 is modified, NS1000 will download System Speed dial data to Super Master CS.

Download Master CS will deliver Data to PS /Other Master CS as Phone book data, after complete download.

The total number of downloaded data is defined by [Site-Property] Note: 1. It will take around 40second to deliver Phone book Data. which is same setting for UT. Default is 300 *1 2. PS will show [Downloading PhoneBook ] as download mode as download mode.

3. Download will start when either [Apply] or [OK] ICON is clicked 4. Can not set Tennant group for PS, so basic Speed dial data is shared by all PS *1: It will take around 5 minutes to complete Phonebook transfer as MAX(256 PS is in One Cell Station) Deliver

51

Appendix

52

Appendix

PS Ring Group #1 (How to work) 1 NS1000 setting by Web-MC Assign CS extension number in NS1000 - Virtual V-UTEXT Port Property

EXT.

200 201 300 301 Status INS INS

2 NS1000 setting by Web-MC Set ICD group - ICD Group Setting

ICD group 600 601 300, 301 Member

3 CS setting by CS-Web Assign CS extension number in each CS 4 CS setting by CS-Web Assign member of PS Ring group in S-Master CS Extn.300

Extn.301

PS Index=P001 Extn.200

PS Index=P002 Extn.201

Index # 1 2 12 Group # 600 Member P001, P002 53

Appendix

PS Ring Group #2 (How to set up) 1. Assign CS extension number Extension numbers must be assigned to all CSs in the same way of UT series SIP phones - Setup- PBX Configuration 1.1 Slot - Virtual V-UTEXT Port Property 2. Set ICD group Extension number of CSs to cover area for PS ringing need to be set in a ICD group as the member. - Setup-PBX Configuration 3.5.1 ICD Group Setting Set CS number as ICD-G member Note: About CS registration into NS1000 No operation is required for registration into NS1000 like as PS.

Registration will be completed automatically when match CS extension number and password on CS with the number on NS1000

54

Appendix

PS Ring Group #3 (How to Set up) 3. Set CS extension number by CS-web Each CS must assign their extension number for PS ring group. Installer needs to log-in into each CS for this setting.

3-1. How to access to each CS Each CS can be logged in from CS-web of Super master CS as follows: 1) Select menu of CS Management.

2) Click Remote Login button for CS that you want to log-in. 3-2. Set extension number in each CS Following items need to be set in each CS when login to CS.

1) Select menu of SIP Settings - CS.

2) Set CS’s extension number into phone number 3) Set Authentication ID (CS’s extension number) 4) Set Authentication Password (“1234”) than, Click Save.

55

Appendix

PS Ring Group #4 (How to Set up) 4. Set PS Ring Group by CS-web PSs are assigned as group member by CS-Web. The setting is required only for Super Master CS.

1) Select menu of PS Ring Group Settings 2) Click PS group registration button of specified group 3) Select PSs from Available Users and move to Group Members by “>” button.

4) Click “All Save” (Setting data is delivered to all CS) 1 2 3 4

56

Air Synchronization

Air Synchronization Mater and Slave CS SIP Based DECT-CS (Mater CS) An CS configured as Master CS will create and send out its own timing and synchronisation.

SIP Based DECT-CS (Slave CS) An CS configured as Slave CS will receive timing and synchronisation from CS set to Master CS.

57

Air Synchronization

Condition of Air Synchronization SIP Based DECT-CS Classification CSs are assigned to any one of the following three classifications for Implementing air synchronization.

CS Class Master CS1 (synchronization source clock) Master CS2 (backup for Master CS1) Slave CS Generates clock signal.

Description - Receives clock signal from Master CS1 - Can also generate clock signal if Master CS1 malfunctions.

Receives clock signal from other CSs.

Master CS1 Level 1 Slave CS Level 2 Slave CS Level 3 Slave CS Level 4 Slave CS Level 8 Level 1 Master CS2 It is recommended that the number of levels in the synchronisation hierarchy is minimized for stable air synchronization. The maximum number of levels is 8

58

IP-CS Air Synchronization

Condition of Air Synchronization Onelook Network Slave CS registered to Slave Unit can NOT Air synchronize with Master CS registered to Master Unit, so it is necessary to install additional Master CS to Slave Unit.

Master Unit Slave Unit Onelook Network Master CS Slave CS Slave CS Master Unit Slave Unit Onelook Network Master CS Slave CS Air Synchronization Group1 Master CS Slave CS Air Synchronization Group2

59

Move CS

How to move registrated CS 1/2 When move CS location which is already registrated, just back up CS data, then initialize CS. After move CS location the restore the back up data . CS-Web Master Slave3 Slave2 Slave4 Move Slave1 Slave4 Slave5 CS Data Back up/Restore Menu 1) Login CS-Web for Slave4 by Installer ID 2) Back up CS data to local PC 3) Reset to Factory data (See 4.2 Step 0) 4) Set Master CS Site survey mode then move CS (See 4.2 Step2) Then finalize CS position

60

Move CS

How to move registrated CS 2/2 When move CS location which is already registrated, just back up CS data, then initialize CS. After move CS location the restore the back up data . CS-Web Tree Survey Menu Master Slave3 Slave2 Slave4 Move Slave1 Slave4 Slave5 5) Restore Back up data 6) Change primary CS index to Master CS (Level1 this case) by tree survey menu, then apply the change Note: After change CS Level, all CS which is in same AirSync Group will be restarted

61

Site Survey (CS)

Set up Temporally CS

62

Site Survey (CS)

Locate Slave CS

63

Site Survey (PS)

CS Cover area check

64

Site Survey (PS)

How to set CS as Maintenance Mode

65

Site Planning tool

How to use Site planning tool General Information 1) This tool assist you planning CS location on your site 2) The tool can be downloaded from CS-Web page How to use 1) Prepare Site Map information by jpg format 2) Then Step1: Load Site Map information to planning tool Step2: Scaling of the Circle Step3: Generation the Service 1.

Aria Circle Step4: Deployment Planning Step5: Repeat Step3 &4 until complete planning 3.

2.

Repeat This Step 4.

66

PS Function List

Detail Function LIST (1) PS Function Following table show PS function Overview Feature NT 3XX SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 DID/DIL incoming call Internal Call Block Ring Tone Pattern Selection Call Waiting Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Idle Extension Hunting Outside Destinations in ICD Queuing Feature Yes Yes Yes Yes Yes Yes Yes Yes Yes VIP Call Log-in/Log-out Yes Yes Yes Yes Yes Yes Call Forwarding (FWD) Do Not Disturb (DND) FWD/DND Button, Group FWD Button Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-DECT (UDS1XX) Yes Yes Yes Yes Remark for SIP DECT Selected by PS Menu No 'Call Waiting Caller ID' on display; Yes Yes Yes 'Hurry-Up' key is not available.

Yes Yes FF key has to be programmed in NS1000 Web-MC Yes Yes Yes 'Group FWD' key is not available.

67

Detail Function LIST (2) Feature Line Preference. Incoming Call Pickup - Directed, Group Hands-free Answerback Automatic Extension Release Emergency Call Account Code Entry Dial Type Selection Pause Insertion Line Preference. Outgoing Trunk Access One-touch Dialing Last Number Redial Speed Dialing. Personal/System Hot Line NT 3XX Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 SIP-DECT (UDS1XX) No Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No No Yes Yes Yes Remark for SIP DECT 'Pause' key is not available..

FF key has to be programmed in PBX FF key has to be programmed in PBX FF key has to be programmed in PBX Yes Yes Yes Yes Yes Yes Personal Download: N/A for SIP-DECT No No No

68

Detail Function LIST (3) Feature PDN/ SDN Automatic Callback Busy Executive Busy Override Call Monitor Call Waiting Tone Off-hook Call Announcement Whisper OHCA Toll Restriction (TRS) Call Barring (Barring) Budget Management Extension Dial Lock Dial Tone Transfer Walking COS Verification Code Entry Automatic Route Selection Hands-free Operation Off-hook Monitor Mute NT 3XX Yes Yes Yes Yes Yes No Yes SIP-MLT UT13X,2XX No SIP based SIP-SLT UT113,123 No No No No Yes No No No No No Yes No No SIP-DECT (UDS1XX) No No Remark for SIP DECT Alternative:Use CA instead Future Future Yes No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes No Yes

69

Detail Function LIST (4) Feature Headset Operation Data Line Security Flash/Recall/Terminate External Feature Access Trunk Call Limitation (CPC) Signal Detection Call Transfer Call Hold Call Park Call Splitting Music on Hold Conference Privacy Release Paging NT 3XX Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 Yes Yes Yes* Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-DECT (UDS1XX) Yes NO Yes Yes Yes Yes Yes Yes Yes Yes Yes Remark for SIP DECT Drop the call without alarm FF key has to be programmed in PBX Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-MLT/SLT: hard "Conf" key, no LED, SIP-DECT: Function Menu, no LED

」

No Yes No Yes No Yes SIP-SLT and SIP-DECT can not be paged

70

Detail Function LIST (5) Feature Conference Group Call Door phone Call Door Open Trunk Answer From Any Station Background Music (BGM) Outgoing Message (OGM) Direct Inward System Access External Sensor External Relay Control Caller ID Incoming Call Log Message Waiting Absent Message NT 3XX SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 SIP-DECT (UDS1XX) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No Yes Yes Yes Yes Yes Yes No No Yes Yes No No Yes Yes Yes Yes Yes Yes No No Yes Yes No No Yes Yes Yes Remark for SIP DECT SIP-MLT/SLT SIP-DECT can be a coordinator Yes Yes Yes Yes No absent message information on LCD while calling.

71

Detail Function LIST (6) Feature Fixed Buttons Flexible Buttons LED Indication Display Information Calling/Connected Line Identification Presentation Advice of Charge (AOC) Built-in SVM Voice Mail (VM) Group Voice Mail DTMF Integration 2WAY-REC 2WAY-Transfer VM-Transfer Live Call Screening (LCS) NT 3XX Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 Yes Yes Yes No Yes Yes Yes Yes SIP-DECT (UDS1XX) Yes Yes Remark for SIP DECT Same limitation as UT Yes Yes Yes Yes Yes No Charge information on LCD. Yes Yes Yes Yes No No No No Yes Yes Yes Yes No No No No Yes Yes Yes Yes No No No No

72

Detail Function LIST (7) Feature PS Ring Group PS Directory PS Feature Buttons Wireless XDP Parallel Mode SMDR Printing Message Call Charge Services Call Billing for Guest Room Extension Personal Identification Number Extension Feature Clear Walking Extension Enhanced Walking Extension Timed Reminder NT 3XX Yes Yes Yes Yes Yes SIP-MLT UT13X,2XX Yes Yes No Yes Yes SIP based SIP-SLT UT113,123 Yes Yes No Yes Yes SIP-DECT (UDS1XX) Yes Yes Yes Yes Yes No Yes Yes Remark for SIP DECT Only support parallel ringing Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes No No No Yes No No No

73

Detail Function LIST (8) Feature Confirmation Tone Calling/Connected Line Identification by QSIG Call Forwarding (CF).by QSIG Call Transfer (CT) by QSIG Completion of Calls to Busy Subscriber (CCBS).by QSIG Network Direct Station Selection Centralized Voice Mail Network ICD Group Peer-to-Peer Connection Self Labeling Computer Telephony Integration NT 3XX Yes SIP-MLT UT13X,2XX SIP based SIP-SLT UT113,123 Yes Yes SIP-DECT (UDS1XX) Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes No Yes Yes Yes Yes No No Yes Yes Yes No Yes Remark for SIP DECT COLP/CONP is not available.

Following enhanced CTI functions are not available -SetDisplay ButtonPressetc.

Communication Assistant Yes Yes Yes Yes

74

Detail Function LIST (9) Feature Class of Service (COS) Group Tenant Service Time Service Operator Features Manager Features System Redundancy Terminal redandancy Stand alone operation NT 3XX Yes Yes Yes SIP-MLT UT13X,2XX Yes Yes Yes SIP based SIP-SLT UT113,123 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes No Yes Yes Yes SIP-DECT (UDS1XX) Yes Yes Yes Yes No Yes Remark for SIP DECT Limited Only do "change the time mode (Day/Night/Lunch/Break)“ by feature access code.

Yes Require to set an external NTP server.

Yes

75

20121107-01 SIP based DECT_Rev1.2_7Nov_fukuda.pptx

- 1 st release 20121202-02 SIP based DECT_Rev1.3_2Dec_fukuda.pptx

- Change #66 Time service line 20121203-03 SIP based DECT_Rev1.4_3Dec_fukuda.pptx

- Add Firmware update process 20121203-04 SIP based DECT_Rev1.5_6Dec_fukuda.pptx

- Change PS registration process as a note Page #45 - Correct model name at SIP based. Wrong:133 -> Correct:113 Page #63-71 - Correct description about flexible key configuration at Remark of SIP DECT, Page #63,64,66 -Add LED information of Site survey mode

END

- Add Site Survey operation in more detail 20121203-05 SIP based DECT_Rev1.6_ 18Dec_fukuda.pptx

- Change Syn Group explanation for One Look System (Page12 ） - Add caution when change CS-Air Setting, the CS will be restarted automatically 20121203-10 SIP based DECT_Rev1.7_ 10Jan2013.pptx

- Corrected Function List checked by Development team 20130124-01 SIP based DECT_Rev1.8_ 24Jan2013.pptx

- Change CS layer ,limitation from 4 to 8(Page 63) 76

2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 12 Ring group 28 -> 128 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 33 LED indication explanation 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 33 Add LOGIN and PASSWORD Information 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 38 Correct Step and screen shot 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 39 Change explanation

END

2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 40 Change explanation 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 44 Change explanation 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 45 Change screen shot 77

2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 45 Change explanation 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 46 Change explanation 2013 02-25 SIP based DECT_Rev1.9 25 Dec 2013 - Changed Page 48 Change explanation

END

78

END

79