No Slide Title

Download Report

Transcript No Slide Title

CSC Track Finder
Florida, Rice, UCLA
Drift Tube Track Finder
Vienna, Bologna
Global Muon Trigger
Global Trigger
Vienna
presented by
Claudia-Elisabeth Wulz
Electronics Week
CERN, 16 May 2002
1st CSC Trigger Prototypes (Florida, Rice, UCLA)
Successful CSC Trigger Integration test
• Prototype Muon Port Card, Sector Receiver,
Sector Processor, Clock Board, Backplane
work & communicate -- Result in 2000
ORCA full simulation working
• Agreement/use with hardware test
C.-E. Wulz
2
Electronics Week, May 2002
CSC Track-Finder Crate Tests
SP
CCB MPC
SR
Very
successful
but latency
too high -New
design in
2001
Bit3
VME
Interface
Custom
backplane
Prototype
crate for
original six
crate design
C.-E. Wulz
100m optical
fibers
3
Electronics Week, May 2002
New CSC Trigger Design: U. Florida Track-Finder
Muon Sorter
SR SR SR SR SR SR
/ / / / / /
SP SP SP SP SP SP
MS
CCB
Clock and Control
Board
BIT3 Controller
Single Track-Finder Crate Design with 1.6 Gbit/s optical links
SR SR SR SR SR SR
/ / / / / /
SP SP SP SP SP SP
SR/SP Card
(3 Sector Receivers +
Sector Processor)
(60 sector)
From MPC
(chamber 4)
From MPC
(chamber 3)
From MPC
(chamber 2)
From Trigger
Timing &
Control
From MPC
(chamber 1B)
From MPC
(chamber 1A)
To
Global Trigger
To DAQ
• Reduces processing time from 525 ns (old design) to 175 ns
• Total Latency ~ 20 Bx (from input of SR/SP card to output of MS card)
• Crate Power Consumption ~ 500 W • 15 Optical connections per SR/SP card
• Custom Backplane for SR/SP  CCB and MS connection
C.-E. Wulz
4
Electronics Week, May 2002
Overall CSC TF Latency
Pre-production prototype data flow
First prototype dataflow
Front FPGAs
1
Lookup tables
Channel link
transmitters
From Muon Port Cards
Sector Receiver st.4
1
Sector Receiver st.2,3
Optical receivers
Sector Receiver st.1
From Muon Port Cards
Optical receivers
1
Front FPGAs
1
Lookup tables
0
3
Extrapolation units
2
9 Track Assembler units (memory)
3
Final selection unit 3 best out of 9
1
Latency
Latency
Channel link receivers
Bunch crossing analyzer (not implemented)
1
2
Pt assignment (memory)
Total: 21 BX
C.-E. Wulz
To Muon Sorter
Sector Processor
Pt precalculation for best 3 muons
Extrapolation units
9 Track Assembler units
Sector Processor
FPGA
1
3
SR/SP board
Bunch crossing analyzer (not implemented)
4
2
To DT
1
1
Total: 7 BX
5
Pt precalculation for 9
muons
Final selection
unit 3 best out of 9
Output multiplexor
Pt assignment (memory)
To Muon Sorter
Electronics Week, May 2002
New Muon Port Card Design & Optical Link Tests (Rice)
New MPC Design
uses new high
speed links
(TLK2501) to send
one muon per
optical fiber
(needed for new compact
track-finder design)
9U * 400 MM
BOARD
VME
INTERFACE
CCB
INTERFACE
3 OPTICAL
CABLES TO
SECTOR
PROCESSOR
OPTICAL
TRANSCEIVERS
OPTO
OPTO
OPTO
SERIALIZERS
SER
SER
SER
VME J1
CONNECTOR
TMB_1
SORTER
LOGIC
TMB_2
INPUT
AND
OUTPUT
FIFO
TMB_4
TMB_3
CUSTOM
PERIPHERAL
BACKPLANE
TMB_5
TMB_6
TMB_7
TMB_8
FPGA
TMB_9
GTLP TRANSCEIVERS
Optical Link Radiation Tests:
Three serializers: up to 270 kRad TID.
No permanent damage or SEU
Two Finisar optical modules:
No errors up to 70 kRad. Failed at 70kRad
(well above ~10 kRad TID inner CSC dose for
10 years)
C.-E. Wulz
6
Electronics Week, May 2002
New Merged Sector Receiver/ Sector Processor (SR/SP)
15 trigger links, 1 DAQ
Small Form
Factor
Transceivers
Deserializer Front
Chips
FPGAs
45 SRAM
Memory
Look-up
Tables
From MPC
(chamber 4)
From
trigger
primitives
~45 SRAM chips
80 MHz speed
VME
Interface
Sector
Processor
FPGA chip
From MPC
(chamber 3)
From MPC
(chamber 2)
From Clock
and Control
Board
To Muon
Sorter
From MPC
(chamber 1C)
Ptassignment
LUTs
From MPC
(chamber 1B)
To/From
Barrel
From MPC
(chamber 1A)
To CSC DAQ
1 April 2001
Output: 60 bits/sector/b.x.
Input: 528 bits/sector/b.x.
C.-E. Wulz
- U. Florida
7
Electronics Week, May 2002
CSC Track Finder Backplane (U. Florida)
Standard VME 64x J1/P1 backplane
SRSP 12
SRSP 11
SRSP 10
SRSP 9
SRSP 8
SRSP 7
Muon sorter
Clock and control
SRSP 6
SRSP 5
SRSP 4
SRSP 3
SRSP 2
Design
Approved
SRSP 1
Standard VME
J2/P2 backplane
Rice
Custom GTLP 6U backplane
These SRSP feedthru
connectors are for DT
information exchange
via transition board
C.-E. Wulz
8
Electronics Week, May 2002
New Muon Sorter Design (Rice)
Reduced to single board -- reduces latency, cost
VME J1
CONNECTOR
9U * 400 MM BOARD
VME
INTERFACE
LVDS DRIVERS
CONNECTORS TO GMT
CCB
INTERFACE
SP1
SP2
SP3
CABLES TO
GLOBAL MUON
TRIGGER CRATE
New:
Will use common
Xilinx mezzanine card
with Sector Processor
SORTER
LOGIC
SP4
INPUT
AND
OUTPUT
FIFO
SP6
SP5
CUSTOM
BACKPLANE
SP7
SP8
SP9
SP10
SP11
SP12
GTLP TRANSCEIVERS
C.-E. Wulz
9
Electronics Week, May 2002
CSC Trigger Status/Plans
Prototype 1 tests now complete
Prototype 2 and production follow EMU
components to optimize technology
MPC, SP, CCC modules, backplane* milestones:
• Apr-02 Prototype 2 designs done
• Freeze CSC-DT interface
• Determine DDU compatibility with OSU module for EMU
• Nov-02 Prototype 2 construction done
• Apr-03 Prototype 2 testing done
• Sep-03 Final designs done
• Oct-04 Production done
• Apr-05 Installation done
(*backplane schedule ~3 months ahead of above dates to
provide platform for testing and integration)
CSC Sorter module: only 1, design by Jan-04
C.-E. Wulz
10
Electronics Week, May 2002
Drift Tube Trigger Track Finder (Vienna, Bologna)
DTTF Sector Processor Board
- simulated with full functionality (including Input Receiver Module)
- fully in behavioral VHDL
- generically in chip VHDL models
- schematics developed and sent for layout at CERN
- Components ordered
- Automatic generation of lookup tables for extrapolation (M. Fierro)
h Track Finder
- VHDL model developed further
- Test bench completed with input and output modules
- Board-level functionality tests performed with VHDL model
(synchronization problems not yet completely cured)
Interface questions answered ...
- Interface between local trigger electronics for j (Padova/Bologna)
- Interface between local trigger electronics for h (Bologna)
C.-E. Wulz
11
Electronics Week, May 2002
DTTF Prototype Development
Hardware
- Backplane developed, layout done in Vienna
- 9U crate corresponding to CERN definition purchased
- New input modules corresponding to the DTTF boards developed and
manufactured
- New output modules functioning with larger data sets developed,
schematics ready, layout to be started soon
Preparations for test
- Test system PC for VME changed, programs newly installed
- New program versions installed and old boards retested
- New logic analyzer purchased
- Investigating several methods for developing prototype test software
Milestone March 2002: DTTF prototype tested -> New: Jan. 2003
C.-E. Wulz
12
Electronics Week, May 2002
DTTF Test Setup
C.-E. Wulz
13
Electronics Week, May 2002
Boards for Test Setup
C.-E. Wulz
14
Electronics Week, May 2002
Global Muon Trigger (Vienna)
New solution with 1 logic board
C.-E. Wulz
15
Electronics Week, May 2002
GMT Logic FPGA
C.-E. Wulz
16
Electronics Week, May 2002
GMT Status and Plans
 Recent progress
 All logic functions defined
• Chip models selected (mostly Virtex II), interconnections defined
• Design compacted (external RAMs moved into big FPGAs)
 Functionality improved
• DT/CSC cancel-out unit (improved performance in barrel/endcap
overlap region)
 Plans for 2002/2003
– continue VHDL simulation of FPGA chips
– VHDL simulation of GMT board
– Synthesis / design of FPGAs
Milestone Dec. 2002: FPGA design done -> Delayed to Dec. 2003
Milestone Nov. 2003: GMT ready -> Delayed
C.-E. Wulz
17
Electronics Week, May 2002
Global Trigger (Vienna)
Backplane and
Readout links
PSB
GTL
FDL
TCS
L1A
TIM
To
DAQ
To
EVM
From
Detector
From
Partitions
PSB (Pipeline Synchronizing Buffer)
GTL (Global Trigger Logic)
FDL (Final Decision Logic)
TCS (Trigger Control System Module)
NEW: L1A (Level-1 Accept Module)
TIM (Timing Board)
GTFE (Global Trigger Frontend)
C.-E. Wulz
GTFE
To
TTC
From
TTC
Input synchronization (7 boards including GMT)
Logic calculation (1-2 boards)
L1A decision (1 board)
Trigger Control (1 board)
Delivery of L1A (1 board)
Timing (1 board)
Readout (1 board)
18
Electronics Week, May 2002
Main Global Trigger Rack
C.-E. Wulz
19
Electronics Week, May 2002
Global Trigger Logic Prototype Board GTL-6U
• GTL-6U
Automatic chip design and setup procedure developed. Layout for a 20 channel
GTL (4 , 4 isol. e/, 4 central jets, 4 fwd jets, SET, ETmiss, 8 jet multiplicities; other
quadruplets can be connected alternatively for tests) is currently being finished.
1020-pin Altera FPGA 20k400E not yet included.
The layout of a conversion board to be used later in final 9U-crate is ready. It
contains also memories in FPGA’s to send simulated test data to the GTL-6U
board.
A decision on a possible redefinition of jet input groups has been taken. It was
decided to keep the present best 4 central jets, 4 forward jets and 4 t-jets and
jet multiplicities for different ET thresholds. A new quantity HT giving the
transverse energy sum of all good jets above threshold has been added. The
exact definition of how to calculate the jet multiplicities (h-range) still has to be
taken at the level of the calorimeter trigger. More than 8 values could be
necessary.
C.-E. Wulz
20
Electronics Week, May 2002
Global Trigger Logic Board GTL-9U
New: HT
C.-E. Wulz
21
Electronics Week, May 2002
New layout of Global Trigger 9U Crate
C.-E. Wulz
22
Electronics Week, May 2002
GTL-6U Prototype Schematics
Design simplified,
board available by Oct. 2002
C.-E. Wulz
23
Electronics Week, May 2002
Final Decision Logic FDL-9U
Schematic and chip design in progress. Board available by Oct. 2002.
Monitoring of all
algorithm and
L1A bits
Prescaling of all
algorithms
Trigger Mask
8 L1A’s in
parallel for
partition modes
Input of up to 64
technical trigger
bits from PSB
possible
C.-E. Wulz
24
Electronics Week, May 2002
Timing Board TIM-6U
• TIM-6U
The board contains a TTCrx chip and provides all timing signals
for the GT crate. It will also be used in the Drift Tube Track
Finder crates.
An FPGA provides all necessary test functions to run the crate
without the central TTC clock. It simulates also L1A requests for
monitoring or to test the readout chain.
The schematic design is finished. The layout is on hold until May
2002 due to TTCrx jitter problems.
The final Timing Board will be 6U (previously 9U).
C.-E. Wulz
25
Electronics Week, May 2002
TIM-6U
C.-E. Wulz
26
Electronics Week, May 2002
New TTCrx Mezzanine Board - Global Trigger Proposal
20 mm VME slot
• Plug-in compatible with
existing TTCrx mezzanine board :
Same pin-out, same mechanical size...
• Mechanics Requests
<16 mm
• Has to fit into 20 mm VME slots
• Replace big jumpers by small switches
• Take SMD capacitors of smaller size
• Mount receiver DIODE for fibre below the board
• Electronics Requests
Seen from front side.
• Add 50 Ohm drivers at least for the CLOCK,
L1A, BCR, … signals
C.-E. Wulz
27
Electronics Week, May 2002
Clock Requirement for Global Trigger
• Max.
cycle-to-cycle jitter of input clock for different chips *)
•Virtex2, Spartan2 chips (DLL, high frequency mode)
 150 ps
•Virtex2, Spartan2 chips (DLL, low frequency mode)
 300 ps
•APEX Altera chips (PLL)  2% at 80MHz 
 250 ps
•National Serializer DS92LV16: Transmitter (GCT,Bristol)
 80 ps (RMS)
•National Deserializer DS92LV16: Receiver (GT,Vienna)
 625 ps (limit)
• RefClk to TxClk =  5% at 80MHz 
•Maximum jitter of clock  150 ps .… Global Trigger requirement, but
•  80 ps Global CalorimeterTrigger requirement, if the calorimeter trigger data are
sent to the Global Trigger using the National Serializer DS92LV16 chips. See also Bristol
presentation.
*) Source: Data sheets for chips
C.-E. Wulz
28
Electronics Week, May 2002
CMS Racks and Crates
CMS RACK Standard:
… decision should be taken
CMS CRATE Standard:
… decision should be taken
Power supplies: different voltage/current combinations should be
possible
•Global Trigger Rack: 6 kW
•Global Trigger Crate VME 9U: 3 kW
•Supply voltages: +5, +3.3, +2.5,+1.8V .....custom GT backplane
•Conversion Crate VME 6U: 1.5 kW
•Supply voltages: +5, -5.2, -2V, ...standard VME backplane
• also with +3.3V (would be fine)
•Emulator Crate VME 6U: 1.5 kW
•Supply voltages: +5, -5.2, -2V, ...standard VME backplane
•maybe also with +3.3V (would be fine)
C.-E. Wulz
29
Electronics Week, May 2002
Trigger Control System Board TCS-9U
• TCS-9U
The main functions are defined but the design is still open for
additional requests (calibration logic etc.) but the number of input /
output cables are defined. The board is expected by Oct. 2002.
Trigger Partitions: The maximum number of subsystems is fixed
(32).
An agreement about the output to the DAQ Event Manager has
been reached.
The input format of Fast Signals is now fixed. 4 coded bits per
subsystem, sent as LVDS parallel data, and RJ45 connectors are
proposed. The TCS board provides data for the new ”CMS-TTCvi”.
A L1A driver module to be used with the CMS-TTCvi has been
conceived.
C.-E. Wulz
30
Electronics Week, May 2002
TCS-9U environment
C.-E. Wulz
31
Electronics Week, May 2002
Global Trigger Milestones in 2002
Milestone March 2002: System Test -> Delayed to Oct. 2002
This includes the backplane, the PSB-6U, GTL-6U, FDL-9U and
TIM-6U. The GTFE and the GMT are not included.
Milestone July 2002: TCS-6U tested -> Delayed to Oct. 2002
Milestone Oct. 2002: Backplane-9U tested -> OK
C.-E. Wulz
32
Electronics Week, May 2002
Further Global Trigger Milestones
Milestone June 2003: Complete GT prototype available
Integration tests possible from this date.
• GTFE-9U: Conceptual design of readout board done.
Milestone July 2004: 12-channel PSB-9U available
• PSB-9U: Conceptual design done. Will have memories inside
FPGA’s.
Milestone Nov. 2004: Complete GT available
Includes GTL-9U module with all input channels
(4 , 4 isol. e/, 4 non-isol. e/ , 12 jet channels, HT , SET, ETmiss, jet
multiplicities).
C.-E. Wulz
33
Electronics Week, May 2002
Conclusions
CSC Track Finder
New single board with sector receiver and sector processor
Reduced latency
New muon sorter
DT Track Finder
Sector processor layout in progress, prototype test with special
input/output modules soon
h track finder in progress
Global Muon Trigger
New single board with barrel and fwd muons on same board
Solution for overlap region with DT/CSC cancel-out unit
FPGA design started
C.-E. Wulz
34
Electronics Week, May 2002
Conclusions
Global Trigger
New processor crate layout, GTL nearly finished, other boards well
advanced
Trigger Control System
Interfaces to subsystems and partition handling defined
This talk can be found at:
http://wwwhephy.oeaw.ac.at/p3w/cms/trigger/globalTrigger/trans/
wulz_ElecWeek_may2002.ppt
C.-E. Wulz
35
Electronics Week, May 2002