Transcript ENP300 - University of Cambridge

DATE : 31. May. ‘01
REVISION No. 1.0
MESSRS.
APPROVAL SHEET
DESCRIPTION :
SET MODEL NO. :
CCD Color Board Camera
CNB - EN300, 350,300C,350C ( NTSC )
CNB - EP300,350,300C,350C ( PAL )
Receipt Stamp
ISSUED
CHECKED
APPROVED
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
REVISION CONTENTS
NO
REVISION CONTENTS
REVISION DATE
Page
REMARKS
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
CCD COLOR BOARD CAMERA
CNB – E
N
3 0 0 C V
1
2
3
4
1
N : NTSC
P : PAL
2
0 : HIGH
5 : NORMAL
3
C : C/CS MOUNT LENS
P : PIN HOLE LENS
V : VARI-FOCAL LENS
4
V : VIDEO IRIS
D : DC IRIS
CONTENTS
PAGE
1. SPECIFICATIONS------------------------------------------------------------ 2
2. MEASUREMENT SPECIFICATIONS------------------------------------ 4
3. ENVIRONMENT CONDITION AND TEST-----------------------------
4
4. INTERFACE-------------------------------------------------------------------
5
5. RECOMMENDED CIRCUIT FOR LOCAL CONTROLS------------
6
6. APPEARANCE----------------------------------------------------------------
9
7. PACKING METHOD---------------------------------------------------------
10
1/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
1. SPECIFICATIONS
Signal System
NTSC ( CNB - EN300/C )
Scanning System
PAL ( CNB - EP300/C )
REMARKS
2 : 1 Interlace
Scanning Frequency ( H )
15.734 KHz
15.625 KHz
Scanning Frequency ( V )
59.94 Hz
50 Hz
Image Sensor
1 / 3 Inch Solid State Interline CCD Image Sensor
Total Pixels No.
811 (H) X 508 (V)
410K
795 (H) X 596 (V)
470K
Effective Pixels No.
768 (H) X 494 (V)
380K
752 (H) X 582 (V)
440K
Signal System
NTSC ( CNB - EN350/C)
Scanning System
SONY
PAL ( CNB - EP350/C )
REMARKS
2 : 1 Interlace
Scanning Frequency ( H )
15.734 KHz
15.625 KHz
Scanning Frequency ( V )
59.94 Hz
50 Hz
Image Sensor
1 / 3 Inch Solid State Interline CCD Image Sensor
Total Pixels No.
537 (H) X 505 (V)
270K
537 (H) X 597 (V)
320K
Effective Pixels No.
510 (H) X 492 (V)
250K
500 (H) X 582 (V)
290K
SONY
“ Bold : Default Mode ”
1) Angle of view at Diagonal
88。 ( f= 3.8 mm )
2) Signal Process
Digital Signal Process
3) Sync System
Internal / External
60。 ( f= 5.8 mm )
4) Camera Function
a) Digital Zoom
ON / Off ( 3 times )
b) Video Focus
Focus free from 0.1m( f= 3.8 mm ) ,0.4m(f= 5.8 mm ) to ∞
c) White Balance
Auto / Indoor / Outdoor / Push Auto / Manual ( R&B Gain Level UP/Down )
Special ( R or B Gain Level Control )
c) Shutter Speed
Auto / Manual (1/60 ~ 1/ 10000 ( NTSC) / 1/50 ~ 1/10000 (PAL) )
d) Iris Control
Fixed / Manual ( Video Iris, DC Iris Optional)
e) Gain Control
Auto / Off
f) Sharpness
Manual ( Sharpness UP ~ Down )
g) Brightness
Manual ( Brightness UP ~ Down )
h) Negative
Off / On
i) Flickerless
Off / On ( 1 / 100 sec Shutter Set (NTSC) / 1 / 120 sec Shutter Set (PAL) )
j) Back Light
Auto / Off / On
2/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
5) Video Output Level
NTSC
PAL
Video Level
0.714 ± 0.07V ( 100 ± 10 IRE)
Sync Level
0.286 ± 0.035V ( 40 ± 10 IRE)
Burst Level
0.286 ± 0.035V ( 40 ± 10 IRE)
Video Level
700 ± 70 mV
Sync Level
300 ± 35 mV
Burst Level
300 ± 35 mV
6) Color Reproduction
COLOR
NTSC
PAL
RED
BLUE
YELLOW
BURST
Amplitude ( % )
200 ± 40 %
130 ± 40 %
115 ± 40 %
100 %(Base)
Phase ( 。 )
103 ± 20。
345 ± 20。
170 ± 20。
180。(Base)
Amplitude ( % )
200 ± 40 %
130 ± 40 %
115 ± 40 %
100 %(Base)
Phase ( 。 )
103 ± 20。
345 ± 20。
170 ± 20。
135。(Base)
7) Horizontal Resolution
More than 470 Lines ( CNB-EN300/C,EP300/C )
More than 380 Lines ( CNB-EN350/C,EP350/C )
8) Luminance S/N
9) Sensitivity
More than 48dB
Typ. 0.5Lux
---- At signal Level 30 IRE
( LENS-F : F = 1.4 ( WIDE )
AGC Gain : Max )
10) Supplied Voltage
9.0 V ~ 15.0 V ( Recommendation 12.0 V ± 0.5 V )
11) Supplied Current
150 mA
12) Power consumption
2.0 W (Max)
13) Dimensions
38.0 (W) × 38.0 (H) × 28.0(D) mm
14) Weight
25 g ( Approx. )
16) Appearance / Dimensions
See Attached Page 8.
17) Packing Method
See Attached Page 9.
3/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
2. MEASUREMENT SPECIFICATIONS
* Standard Measurement Condition and Measurement Procedure
See an Annexed Document “ APPENDIX 2 ”
3. ENVIRONMENT CONDITION AND TEST
1) Operating Condition
2) Storage Condition
Temperature
-10 。C ~ 50。C ( Recommendation : - 5 。C ~ 40。C )
Humidity
10 % ∼ 85 %
Temperature
Humidity
-20 。C ~ 60。C
0 % ∼ 90 %
3) High Temperature storage Test
Leaving the packed at Temperature of 60。C for 72 Hours, and after leaving it at
Normal Temperature for 8 Hours, there should be no Problem in Performance.
4) Low Temperature storage Test
Leaving the packed at Temperature of -20。C for 72 Hours, and after leaving it at
Normal Temperature for 8 Hours, there should be no Problem in Performance.
4/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
4. INTERFACE
1) Pin Assignment ( J204, 7 Pin Connector ; Maker Molex/Yenho , 12512WS-07A00,Pitch 1.25 mm )
PIN No.
NAME
I/O
Note
1
VIDEO OUT
Output
1.0 Vp-p at 75Ω
2
GND (For Video)
3
DC IN (ALIVE)
Input
9 V ~ 15 V ( Recommendation 12±0.5 V )
4
A/D KEY
Input
See Attached Page 6.
5
GND
6
Line VD
Input
See Attached Page 6.
7
5V OUT
Output
FOR AC 24V Line VD(Not used)
2) Pin Assignment ( J203, 4 Pin Connector ; Maker Molex / Yenho, 12505WS-04A00,Pitch 1,25 mm )
: RS-232C TTL
See an Annexed Document “ APPENDIX 3 ” (PROTOCOL)
PIN No.
NAME
I/O
LEVEL
1
RD(For RS-232C)
Input
CMOS Level 5V ( Low : Max 0.8V , High : Min 3.7V )
2
TD(For RS- 232C)
Output
CMOS Level 5V ( Low : Max 0.8V , High : Min 3.7V )
3
5V
4
GND
Output
FOR RS-232C ( Not used)
FOR RS-232C
3) Pin Assignment ( J205, 4 Pin Connector ; Maker Molex / Yenho , 12505WS-04A00, 1.25 mm )
* Optional DC/VIDEO TYPE
PIN No.
DC IRIS
1
DAMP +
N.C
2
DAMP -
12V
3
DRIVE +
V. LEVEL
4
GND
GND
VIDEO IRIS
5/10
LEVEL
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
5. RECOMMENDED CIRCUIT FOR LOCAL CONTROLS
1) Selectable KEY Function
NO.
Function
NO.
Function
1
Tele (Digital Zoom)
16
Backlight On / Off
2
Wide (Digital Zoom)
17
Color / Black
3
Pan Right
18
Initial Set
4
Pan Left
19
Power On / Off
5
Tilt Up
20
6
Tilt Down
21
7
Auto Pan
22
8
Auto Tilt
23
9
Flickerless On /Off
24
Red control
10
WB Push Auto
25
Blue control
11
Brightness (Negative) Control ( + )
26
Mirror
12
Brightness (Negative) Control ( - )
27
Auto Zoom
13
Sharpness Control ( + )
28
AGC On/Off
14
Sharpness Control ( - )
29
15
Positive / Negative
30
1-1) KEY Function
J204
A/D KEY
0.01uF
6.8K
8.2K
12K
18K
33K
68K
180K
4
POWER
ON/OFF
TELE(+)
WIDE(-)
COLOR /
BLACK MIRROR
Auto
Pan
Auto
Tilt
Initial Set
2 ) Line In Pulse ( EX. FV)
5V
0V
Min : 200 nsec
60 Hz ± 0.25 Hz ( NTSC )
50 Hz ± 0.25 Hz ( PAL)
A) Pulse- Signal Spec of EX.FV
6/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
3) PWB LAY OUT (CSP BOARD)
VR201
SW201
LOW
HIGH
DC LEVEL
1 2 3 4
4
J205
1
IC 204
7
J204
1
1
4
J203
4) SW Assignment ( SW201:MSH-04)
LOW
1
2
3
4
PIN No.
LOW
1
BLC ON
BLC OFF
2
ALC
ELC
3
AGC OFF
AGC ON
4
Digital Zoom x2
Digital Zoom x1
HIGH
HI
7/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
4 - 1) Selectable SW Function
Option 1
PIN No.
1
LOW
MIRROR ON
HIGH
PIN No.
MIRROR OFF
3
4
FUNCTION
HIGH
HIGH
Digital Zoom X1
2
ALC
ELC
HIGH
LOW
Digital Zoom X2
3
Zoom 1
Zoom 1
LOW
HIGH
Digital Zoom X3
4
Zoom 2
Zoom 2
LOW
LOW
LOW
HIGH
Auto ( X1 ~ X3 ~X1 )
Option 2
PIN No.
BLC ON
1
BLC OFF
2
ALC
ELC
3
Flickerless ON
Flickerless OFF
4
Digital Zoom x2 Digital Zoom OFF
Option 3
PIN No.
1
LOW
BLC ON
HIGH
BLC OFF
2
ALC
ELC
3
Flickerless ON
Flickerless OFF
4
AGC ON
AGC OFF
Option 4
PIN No.
1
LOW
BLC ON
2
ALC
3
MIRROR ON
4
HIGH
BLC OFF
ELC
MIRROR OFF
Digital Zoom x2 Digital Zoom OFF
8/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
6. APPEARANCE
H=2.5
ON
H=4.8 1
H=3
MVR32
1 234
IMAGE PLANO
H=4.2
H=4.8 1
focal length3.6
B.F.L. 5.6
8.2*8.8*3.27
나라1/4" NOR
MHS04
9/10
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
7. PACKING METHOD
5x4
5x4
5x4
5x4
5x4
10/10
C&B Technology Inc.
APPENDIX 2
DATE : 17. May. ‘01
REVISION No. 0.9
Measurement Specifications
MODEL
CNB - EN300/C, 350/C
CNB - EP300/C, 350/C
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
1. MEASUREMENT CONDITIONS
1) Standard Measurement Conditions
Supplied Voltage
DC 12V ± 0.5 V
Ambient Temperature
23 ℃
Humidity
60 % RH
Measurement Fixture
Video output , DC input , RS-232C level Convert ( 5Vpp -> 12Vpp)
Power Supply
12V ± 0.5 V
Color Monitor
CMM20 - 11 , Shibasoku or Equivalent
Monochrome Monitor
More than 800 TV Lines Horizontal Resolution
Waveform Monitor /
Vector Scope
1720 , Tektronix ( NTSC / EIA ) or Equivalent
1730 , Tektronix ( PAL / CCIR ) or Equivalent
E S / N ( Signal to Noise )Meter
VN31AX , Shibasoku ( NTSC/PAL/EIA/CCIR ) or Equivalent
Q Illumination Meter /
U
Color Temperature Meter
XY-1 / CL-100 , Minolta Camera or Equivalent
I
Light
Box
Dai Nippon Printing Co.
P
- Color Temperature
3200。K ± 100 。K
M
E
- Illumination
More than 2000 Lux
N Test Charts
( Transparent Chart )
T
Color Bar Chart , Dai Nippon Printing Co.
S
Gray Scale Chart , Dai Nippon Printing Co. ( Gamma 0.45 )
Resolution Chart , Dai Nippon Printing Co. ( Reflective Chart )
Gray Scale Chart , Murakami Color Research Lab
Light Source
Halogen Lamp ( with Dimmer Switch )
- Color Temperature
3200。K ± 100 。K
- Illumination
Variable with Dimmer
Color Temperature Filter
LB 140 , Hoya or Kenko or Equivalent
( Color Temperature Conversion Filter )
Adjustment PC
RS-232C Cable
With Serial Port 1 or 2
Each Terminal Connector ( D-Sub 9 Pin )
2. Measuring System
1) System 1.
Camera
Light Box
PC with
Serial Port
2) System 2.
FFC
Measurement
Fixture
Color
Monitor
Waveform /
Vector scope
Monochrome
Monitor
Light Source
Camera
Same as above System 1.
Reflective Chart
1/5
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
2. MEASUREMENT PROCEDURE
1. VIDEO OUPUT LEVEL
TEST CONDITIONS
Refer to “ 1. MEASUREMENT CONDITIONS “
MEASURING SYSTEM
System 1.
PROCEDURE :
1.
Shoot the gray scale chart , and move the camera to fit a scene of monitor fully and bring
the chart into focus.
2. Measure the video output level on the waveform monitor
( Before the above measurement , Measure the SYNC and BURST level )
A
C
B
( Fig 1. ) Video Output Waveform
SPECIFICATION :
NTSC
PAL
Video Level A
100 ± 10 IRE
Sync Level B
40 ± 5 IRE
Burst Level C
40 ± 5 IRE
Video Level A
700 ± 70 mV
Sync Level B
300 ± 35 mV
Burst Level C
300 ± 35 mV
2/5
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
2. COLOR REPRODUCTION
TEST CONDITIONS
Refer to “ 1. MEASUREMENT CONDITIONS “
MEASURING SYSTEM
System 1.
PROCEDURE :
1. Shoot the color bar chart , and move the camera to fit a scene of monitor fully and bring
the chart into focus.
2. Measure the color amplitude and color phase on the vector scope of Red,Blue,Yellow .
( Before the above measurement , Adjust the burst amplitude and phase on the vectorscope
so that the burst level becomes 100% and its phase becomes 180 。 (NTSC) (135 。 PAL)
( Fig 2. ) Video Output Waveform
( Fig 3. ) Video Output Color Vector
SPECIFICATION :
COLOR
NTSC
PAL
RED
BLUE
YELLOW
BURST
Amplitude ( % )
200 ± 40 %
130 ± 40 %
115 ± 40 %
100 %
Phase ( 。 )
103 ± 20。
345 ± 20。
170 ± 20。
180。
Amplitude ( % )
200 ± 40 %
130 ± 40 %
115 ± 40 %
100 %
Phase ( 。 )
103 ± 20。
345 ± 20。
170 ± 20。
135。
3/5
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
3. LUMINANCE S / N
TEST CONDITIONS
Refer to “ 1. MEASUREMENT CONDITIONS “
MEASURING SYSTEM
System 1.
PROCEDURE :
1. Shoot the light box , and move the camera to fit a scene of monitor fully and bring
the chart into focus.
2. The noise meter settings are ;
Input level
: Preset
High Pass Filter
: 100KHz
Low Pass Filter
: 4.2 MHz
Sub-carrier Trap
: On
Weighting
: On
Sag & Hue Comp.
: Optimum
3. Measure the maximum S/N on the noise meter .
SPECIFICATION :
NTSC : More than 48 dB
PAL : More than 48 dB
4. HORIZONTAL RESOLUTION
TEST CONDITIONS
Refer to “ 1. MEASUREMENT CONDITIONS “
MEASURING SYSTEM
System 1.
PROCEDURE :
1. Shoot the resolution chart , and move the camera to fit a scene of monitor fully and bring
the chart into focus.
2. Adjust the brightness and contrast of the B/W monitor so that each steps of resolution chart
can be observed .
3. Change the scan size of monitor to underscan.
4. The reference arrows on the resolution chart are positioned at theedge of the underscanned
picture .
5. Change the scan size of monitor from underscan to overscan .
6. Measure the maximum horizontal resolution on the picture .
SPECIFICATION :
More than 470 TV Lines ( High Resolution )
More than 380 TV Lines ( Normal Resolution )
4/5
C&B Technology Inc.
CNB-EN300/300C/350350C, EP300/300C/350350C Specifications
5. LOW LUMINANCE SENSITIVITY
TEST CONDITIONS
Refer to “ 1. MEASUREMENT CONDITIONS “
MEASURING SYSTEM
System 2.
PROCEDURE :
1. Shoot the gray scale chart ( reflective ), and move the camera to fit a scene of monitor
fully and bring the chart into focus.
2. Adjust the brightness of the light source by using the dimmer switch so that the white peak level
of the chart becomes 30 IRE ( NTSC ) ,( 210 mV ,PAL) on the waveform monitor .
3. Measure the level of illumination by using the illumination meter .
SPECIFICATION :
NTSC (HI)
PAL (HI)
: 0.5 Lux ( 30 IRE )
: 0.5 Lux ( 210 mV )
NTSC (Normal)
PAL (Normal)
: 0.1 Lux ( 30 IRE )
: 0.1 Lux ( 210 mV )
5/5
C&B Technology Inc.