Transcript bpTT HSSE OSH COMPLIANCE GAP CLOSURE

Pre Engineering
Risk Management
Rajesh Kandhai
Recap - Hazard
Hazard – source (e.g. substance, activity, event
or environment) or situation that could potentially
cause harm in terms of human injury, or ill health,
damage to property, damage to the workplace
environment, or a combination of these (adapted
from OHSAS 18001:2007)
Recap - Risk
 The
combination of the likelihood
(probability) and the consequence (s) of a
specific hazardous event occurring.
 Risk
= likelihood x consequences (x no. of
people affected)
Risk Assessment – 5 steps to risk
assessment

A risk assessment is simply a careful
examination of what, in your work, could
cause harm to people, so that you can weigh
up whether you have taken enough
precautions or should do more to prevent
harm. Workers and others have a right to be
protected from harm caused by a failure to
take reasonable control measures.
Assessing workplace risk
 Step
1 Identify the hazards
 Step 2 Decide who might be harmed and how
 Step 3 Evaluate the risks and decide on
precautions
 Step 4 Record your findings and implement
them
 Step 5 Review your assessment and update if
necessary
Step 1 - Identify the Hazard





Walk around your workplace and look at what could
reasonably be expected to cause harm.
Ask your employees or their representatives what
they think. They may have noticed things that are not
immediately obvious to you.
If you are a member of a trade association, contact
them. Many produce very helpful guidance.
Check manufacturers’ instructions or data sheets for
chemicals and equipment as they can be very helpful
in spelling out the hazards and putting them in their
true perspective.
Remember to think about long-term hazards to health
(eg high levels of noise or exposure to harmful
substances) as well as safety hazards.
Types of Hazards
 Hazards







may be of varying types:
Physical
Mechanical
Electrical
Chemical
Biological
Ergonomic
Psychological
Hazards continued
 After
understanding the work to be done, try
to identify the possible scenarios:






Physical – noise from equipment, temperature in room
Mechanical – pinch points, crush points, vehicle
collisions
Electrical
Chemical – exposure, storage, compatibility
Ergonomic – strains form tasks (manual handling etc)
Psychological – stress from deadlines, work load,
unrealistic management requests.
Step 2 – Who might be harmed
 For
each hazard you need to be clear about
who might be harmed; it will help you
identify the best way of managing the risk.
That doesn’t mean listing everyone by name,
but rather identifying groups of people (eg
‘people working in the storeroom’ or
‘passers-by’).
Step 3 – Evaluate the risk and
decide on precautions

look at what you’re already doing, think about what
controls you have in place and how the work is
organised. Then compare this with the good practice
and see if there’s more you should be doing to bring
yourself up to standard. In asking yourself this,
consider:




Can I get rid of the hazard altogether? If not, how can I
control the risks so that harm is unlikely?
When controlling risks, apply the principles below, if possible
in the following order:
try a less risky option (eg switch to using a less hazardous
chemical); prevent access to the hazard (eg by guarding);
organise work to reduce exposure to the hazard (eg put
barriers between
pedestrians and traffic); issue personal protective equipment
(eg clothing, footwear, goggles etc); and provide welfare
facilities (eg first aid and washing facilities for removal of
contamination
Risk evaluation - likelihood
Likelihood of
occurrence
Description of rating
Rating
Very Unlikely Impact highly unlikely to occur
1
Unlikely
Impact unlikely to occur
2
Possible
Impact likely to occur
3
Likely
Impact highly likely to occur
4
Very Likely
Impact Certain to occur
5
Risk Evaluation - Consequence
Severity
rating
Negligible
No observable effect
1
Slight
Impact restricted to fewer than three
Lost time days
2
Moderate
Minor Fracture - permanent injury/
disability
3
High
Single Fatality
4
Very high
Multiple fatalities
5
Risk Matrix
Hazard Severity
1 Negligble
Likelihood of occurrence
2 Slight
3 Moderate
4 High
5 Very High
1 Very Unlikely
1
2
3
4
5
2 Unlikely
2
4
6
8
10
3 Possible
3
6
9
12
15
4 Likely
4
8
12
16
20
5 Very Likely
5
10
15
20
25
Action levels
No new action required. Continual
Monitoring of existing controls
Implement control measures and
conduct monitoring to ensure
effectiveness
Activity should not be started or
continued until risk reduction
measures implemented. Immediate
action required
Step 4 – Record and implement
findings



Putting the results of your risk assessment into
practice will make a difference when looking after
people and your business.
Writing down the results of your risk assessment, and
sharing them with your staff, encourages you to do
this. If you have fewer than five employees you do
not have to write anything down, though it is useful
so that you can review it at a later date if, for
example, something changes.
When writing down your results, keep it simple, for
example ‘Tripping over rubbish: bins provided, staff
instructed, weekly housekeeping checks’, or ‘Fume
from welding: local exhaust ventilation used and
regularly checked’.
Step 5 – Review and update




Few workplaces stay the same. Sooner or later, you will bring in new
equipment, substances and procedures that could lead to new
hazards. It makes sense, therefore, to review what you are doing on
an ongoing basis. Every year or so formally review where you are, to
make sure you are still improving, or at least not sliding back.
Look at your risk assessment again. Have there been any changes? Are
there improvements you still need to make? Have your workers
spotted a problem? Have you learnt anything from accidents or near
misses? Make sure your risk assessment stays up to date.
When you are running a business it’s all too easy to forget about
reviewing your risk assessment – until something has gone wrong and
it’s too late. Why not set a review date for this risk assessment now?
Write it down and note it in your diary as an annual event.
During the year, if there is a significant change, don’t wait. Check
your risk assessment and, where necessary, amend it. If possible, it is
best to think about the risk assessment when you’re planning your
change – that way you leave yourself more flexibility.
Example of a Job Hazard Analysis
 Failure
to identify and evaluate the hazard
and risk
Exercise 4
Cleaning the Cafeteria
How can I get
hurt? (Hazards)
What would my injuries be?
(Hazard Effect)
What can I do to prevent
my being hurt? (Control)
Exercise 4
An Electrician is drilling through a wall with an
electric hand drill.
1. How might this person be injured?
(Note; NOT what the injury might be but what
might or would CAUSE him to be injured)