Transcript - Fulcrum
MAINTENANCE SHEETS FOR OFF-ROAD WHEELS UNIT TYPE GRUPPO RUOTEWHEELS STRADA OFF-ROAD OPERATION TIPOLOGIA MOVIMENTO CONO / CALOTTA OPERAZIONE 008 MOVEMENT OF CONES / BOTTOM BRACKET CUPS DISC BRAKE 008 REVISION REVISIONE 0/2011 01- 11 PRODOTTI SUI QUALI APPLICARE LA PROCEDURA DESCRIPTION DESCRIZIONE REMOVAL AND REFITTING OF THE FREE WHEEL SMONTAGGIO E RIMONTAGGIO CORPO RUOTA /2016LIBERA BODY WITHPOSTERIORE MOVEMENT CON OF CONES / BOTTOM RUOTA MOVIMENTO CONO/CALOTTA BRACKET CUPS PRODUCTS TO WHICH THIS PROCEDURE APPLIES RED CARBON RED Red METAL ZERO Metal 0 XRP XRP Red Carbon XRP™ 1 2 2 the locknut completely. Insert1 a 17mm open-end spanner in the locknut of the hub Loosen Inserire la chiave fissa da 17 sul controdado del perno pivot. Insert the 5mm hexagon wrench in the hexagon of Svitare completamente il controdado. mozzo. Inserire la chiave esagonale da 5 all’interno the pivot, and turn the locknut anti-clockwise. dell’esagono del perno e svitare il controdado in senso 3 3 the resin spacer. Remove Rimuovere il distanziale in resina. antiorario. 4 4 the pinion-holder element from the hub pivot. Remove Togliere il corpo portapignoni dal perno del mozzo. 5 6 5 If necessary, grease the inside of the FW body ratchets as Insert6 the FW body in the rear pivot. Se necessario ingrassare anche all’interno dei Inserire il corpo ruota libera sul perno posteriore well. OPERATION 013. cricchetti del corpo ruota libera. OPERAZIONE 013. 7 8 Use a7screwdriver to insert the ratchets in the rack insert. Insert8 the FW body completely. Con un cacciavite inserire all’interno dell’inserto a cremagliera i cricchetti. 10 10 the locknut on the pivot. Tighten Avvitare il controdado sul perno. Inserire completamente il corpo ruota libera. 11 11the 5mm hexagon wrench in the pivot and, keeping Insert la chiave da using 5 all’interno del perno itInserire stationary, tightenesagonale the locknut the 17mm torque e tenendola fissa avvitare il controdado con la chiave wrench. dinamometrica da 17. 9 Insert9 the spacer. Inserire il distanziale. TECHNICAL MANUAL - OFF ROAD XRP ™ MAINTENANCE SHEETS FOR OFF-ROAD WHEELS UNIT TYPE OPERATION REVISION DESCRIPTION OFF-ROAD WHEELS DISC BRAKE INDUSTRIAL BEARINGS/CONES-BOTTOM BRACKET CUPS 008 01- 11 /2016 DISASSEMBLY AND REFITTING OF THE FREE WHEEL BODY PRODUCTS ON WHICH TO APPLY THE PROCEDURE RED POWER HP (2015) RED POWER C23 / HP / BOOST 1 On the left side, remove the external adapter. It is not necessary to remove the QR adapter (if this is fitted). 4 Remove the adapter and the spacer (if fitted). 7 If necessary, grease the inside of the FW body pawls as well. RED PASSION / RED PASSION 3 / BOOST 2 Block the pivot on the left side, using a 14mm cone wrench. 5 Remove the FW body from the hub pivot. 8 Insert the FW body on the pivot. 3 Loosen the right-hand adapter, using a 17mm wrench. Pay attention to the left-hand thread! 6 Grease the inside of the rack insert with lithium grease. the quantity of grease inserted should cover about 75% of the free space of the rack insert. 9 Using a screwdriver, move the pawls into the closed position and, slowly rotating the FW body, insert them in the rack. TECHNICAL MANUAL - OFF ROAD RED POWER (2015) MAINTENANCE SHEETS FOR OFF-ROAD WHEELS UNIT TYPE OPERATION REVISION DESCRIPTION OFF-ROAD WHEELS DISC BRAKE INDUSTRIAL BEARINGS/CONES-BOTTOM BRACKET CUPS 008 01- 11 /2016 DISASSEMBLY AND REFITTING OF THE FREE WHEEL BODY PRODUCTS ON WHICH TO APPLY THE PROCEDURE RED POWER HP (2015) RED POWER C23 / HP / BOOST 10 Insert the adapter on the right, and tighten it. Attention: left-hand thread! 13 Insert the external adapter on the left side. RED PASSION / RED PASSION 3 / BOOST 11 On the left, insert a 14mm cone wrench on the pivot. 12 Screw in the bushing on the right, using a 17mm socket spanner. Tighten to a torque of 12 Nm. Attention: lefthand thread! TECHNICAL MANUAL - OFF ROAD RED POWER (2015)