Transcript IEEE C802.16m-09/2239r5

CoFIP Pilot Sequences
Document Number: IEEE C80216m-09_2239r5
Date Submitted: 2009-17-05
Source:
Padmanabhan M S, Kiran Kuchi, J. Klutto Milleth, Sivakishore
CEWiT, India
Voice:
E-mail:
[email protected],
[email protected]
Venue: Comments
on P802.16m/D2 (15.3.11.3.3)
Base Contribution: None
Purpose: To discuss and adopt the proposed text in D3
To discuss in TGm for appropriate action. Notice:
This document does not represent the agreed views of the IEEE 802.16 Working Group or any of its subgroups. It represents only the views of the participants listed in the “Source(s)” field
above. It is offered as a basis for discussion. It is not binding on the contributor(s), who reserve(s) the right to add, amend or withdraw material contained herein.
Release:
The contributor grants a free, irrevocable license to the IEEE to incorporate material contained in this contribution, and any modifications thereof, in the creation of an IEEE Standards
publication; to copyright in the IEEE’s name any IEEE Standards publication even though it may include portions of this contribution; and at the IEEE’s sole discretion to permit others to
reproduce in whole or in part the resulting IEEE Standards publication. The contributor also acknowledges and accepts that this contribution may be made public by IEEE 802.16.
Patent Policy:
The contributor is familiar with the IEEE-SA Patent Policy and Procedures:
<http://standards.ieee.org/guides/bylaws/sect6-7.html#6> and <http://standards.ieee.org/guides/opman/sect6.html#6.3>.
Further information is located at <http://standards.ieee.org/board/pat/pat-material.html> and <http://standards.ieee.org/board/pat >.
CoFIP pilot sequences
specification
Pilot sequences for CDR with CoFIP

The pilot sequences assigned to different cells should
have low cross correlation within the space of an RB.

Some of the possibilities are:

Use of short pilot sequences, which have low cross-correlation within a
localized resource unit.

Use of long PN sequences

Results in increased cross correlation
Short PN sequence




Seven PN sequences are generated using an LFSR with the
characteristic polynomial X3+X +1
The first 6 samples of a sequence is used for deriving the 6 pilots with
in a PRU
Definitions:

A cluster is a collection of 3 sectors and is assigned unique cluster id = CID

PRU index ‘s’ in frequency and sub-frame number ‘t’ in time.
Pilot codebook C = { c(0),c(1),c(2), c(3), c(4),c(5), c(6) } is defined in
table 1.
Pilot codebook
Table 1
Pilot sequence cycling

Pilot sequence cycling in time and/or frequency is implemented to
exploit the advantage of interference averaging on the pilots. The
pilot code used in a cell with CID = k is C( (s+t+k)%7), where C(i) is
the ith code of the set of codes C. i=0,1,…6
t -->
s
CID = 0
CID=1
CID=2
CDR Performance comparison between short
and long PRBS
Proposed Text
……………………..Start of Text……………………………………………………….
Section 15.3.11.3.3, Page 541, line 56
In Type 1 OL MIMO region, the pilot sequence used to modulate the CoFIP pilot
subcarriers shall be obtained from the set of pilot modulation sequences
defined in Table xxx. The sequence index used for modulation of PRU pilot
subcarriers is derived from i= mod(s+t+mod(mod(IDCell,256), 7),7), where s
is the physical PRU index, t is the physical subframe index.
Sequence
index
Pilot Modulation
Sequence
0
[-1 -1 1 1 1 -1]
1
[-1 1 -1 -1 1 1]
2
[-1 1 1 1 -1 1]
3
[1 -1 -1 1 1 1]
4
[1 -1 1 -1 -1 1]
5
[1 1 -1 1 -1 -1]
6
[1 1 1 -1 1 -1]
Table xxx Pilot Modulation Sequences for CoFIP