Transcript Engineering 4862 Microprocessors Lecture 22 Cheng Li EN-4012

Engineering 4862 Microprocessors
Lecture 22
Cheng Li
EN-4012
[email protected]
8088 / 8086 CPU in Min Mode
Engr 4862 Microprocessors
8086/88 uPro and Supporting Chips
– Pin descriptions for 8086/88
• BHE (Active Low, Bus High Enable): Pin 34
– Used to distinguish between the low byte and the high byte of the
data for the 16-bit external data bus of 8086
– Together with A0
BHE
A0
0
0
16-bit D0-D15
0
1
8-bit
Upper half, D8-D15
1
0
8-bit
Lower half, D0-D7
1
1
Data Bus Idle
• NMI (Non-Maskable Interrupt)
– An rising edge-triggered input signal to the processor
• READY
– Low level-active signal, insert a WAIT state
Engr 4862 Microprocessors
8086/88 uPro and Supporting Chips
– Pin descriptions for 8086/88
• INTR (Interrupt Request)
– An active-high level-triggered input signal to the processor
– Sampled in the last clock cycle of each instruction
– In IBM PC, this is connected to the 8259 Interrupt controller
• Clock (heart beat of CPU)
– Need to be accurate for event synchronization and driving CPU
– An input signal and is connected to 8284 clock generator
• RESET
– Active high signal came from 8284
– Force the uPros to stop any activities and to discard everything
– Data after reset:
CS: FFFFH, IP: 0000H, DS ES SS: 0000H
Flags: Cleared, Queue: Empty
Engr 4862 Microprocessors
Min / Max Mode (Pin 24–31)
– Minimum mode
•
•
•
•
Pin #33 (MN/MX) connect to +5V
Pin 24-31 are used as memory and I/O control signal
The control signals are generated internally by the 8086/88
More cost-efficient
– Maximum mode
• Pin #33 (MN/MX) connect to Ground
• Some control signals are generated externally by the 8288
bus controller chip
• Max mode is used when math processor is used.
Engr 4862 Microprocessors
Control Signal Generation in Min Mode
Engr 4862 Microprocessors
Three Buses in 8088 Based System
Engr 4862 Microprocessors
Min / Max Mode (Pin 24–31)
– Maximum mode
• S2, S1, S0
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
connect directly to 8288
INTA
Interrupt Acknowledgment
IORC
Read I/O Port
IOWC
Write I/O Port
NONE
Halt
MRDC
Code Access
MRDC
Read Memory
MWTC
Write Memory
Passive
None
Engr 4862 Microprocessors
8086/8088 in Max Mode
Engr 4862 Microprocessors
8288 Bus Controller
Engr 4862 Microprocessors
The Clock
• The clock signal is very important to the
operation of a microprocessor circuit.
• It synchronizes the sequential activities of
the CPU and the system
– Not all devices use a clock signal (eg. PPI)
Engr 4862 Microprocessors
8284 Clock Generator and Driver
• The 8088/8086 CPUs require a specific
waveform for the system clock
–
–
–
–
Fast rise and fall times ( <10ns )
Logic 0: -0.5 to 0.6 V
Logic 1: 3.9 to 5.0 V
Duty cycle of 33%
Engr 4862 Microprocessors
8284 Clock Generator and Driver
33% Duty Cycle
Engr 4862 Microprocessors
8284 Clock Generator
Engr 4862 Microprocessors
8284 Clock Generator and Driver
• The 8284 provides the proper clock signal
– Uses a crystal oscillator (3 oscillations per
clock)
• Provides the correct waveforms for other
signals to CPU
– RESET
– Request for wait state
Engr 4862 Microprocessors
8284 Clock Generator and Driver
– An 18-pin chip. Not only provide the clock and
synchronization for the microprocessor, but also
provides the READY signal for the insertion of WAIT
states into the CPU bus cycle.
– Input Pins
• RES (Reset In): from power supplier
• X1 and X2 (Crystal In): the crystal frequency must be 3
times the desired frequency for the microprocessor
– For IBM PC, 14.31818 MHz (max 24 MHz)
• RDY1 and AEN1: provide a Ready signal to the mPro,
which will insert a WAIT state to the CPU read/write cycle.
• RDY2 and AEN2: For multiprocessor systems
Engr 4862 Microprocessors
8284 Clock Generator and Driver
– Output Signals
• RESET: reset signal to the 8086/88, activated by RES
• OSC (oscillator): provide to the expansion slot
• CLK (clock): 1/3 of the OSC or EFI input, with a duty cycle
of 33%
– In IBM PC, OSC = 14.31818 MHz, so CLK = 4.772776 MHz
• PCLK: one-half of CLK (1/6 of crystal) with duty cycle of
50% and is TTL compatible. Provide to 8253 Timer to
generate speaker tones
• READY: connect to READY input of CPU to insert WAIT
state
Engr 4862 Microprocessors
Other Supporting Chips
– 8288 Bus Controller
• A 20-pin chip to provide all the control signals when the
8086/88 is in the maximum mode
– 74LS373 Latch
• Provide isolation and bus boosting
– 74LS244 Unidirectional data transceiver chip
– 74LS245 Bidirectional data transceiver chip
• Provide bus buffering and boosting
Engr 4862 Microprocessors
Machine Cycles
• Also Bus Cycles
• Definition:
– One discrete information transfer on the buses.
• This includes the address, data, and control
information.
Engr 4862 Microprocessors
Machine Cycles
• A machine (bus) cycle consists of at least
four clock cycles, called T states.
• A specific, defined action occurs during
each T state (labeled T1 – T4)
–
–
–
–
T1: Address is output
T2: Bus cycle type (Mem/IO, read/write)
T3: Data is supplied
T4: Data latched by CPU, control signals
removed
Engr 4862 Microprocessors
By memory or I/O device
By microprocessor
Engr 4862 Microprocessors
T States
• Why are there T states?
– In the 8086/8088, the address and data lines are
multiplexed.
– The microprocessor needs time to change the
signals during each bus cycle.
– Memory devices need time to decipher the
address value and then read/write the data
(access time)
Engr 4862 Microprocessors
Timing
• The period of one bus cycle is at least four
times a clock cycle
– 10-MHz 8086 CPU
– Each clock cycle has a period of 100ns
– Machine cycle period is 400ns
Engr 4862 Microprocessors
Timing
400 ns
100 ns
Engr 4862 Microprocessors
Timing
• Although the system clock has a constant
period, the bus cycle does not
– Slow devices (memory or I/O) must request
extra time.
– The microprocessor inserts extra wait states
between states T3 and T4
• The alternatives are to slow down the
system clock, or use faster devices
Engr 4862 Microprocessors
Timing
Wait state inserted
here
Engr 4862 Microprocessors
I/O Design
• When designing an I/O port, ensure that the
port is only active when selected by the
microprocessor
– Use latches (output) and buffers (input) to
isolate the I/O port circuitry from the address
and data bus
– Use the correct combinatorial logic circuitry
and/or decoders with address bus to select the
port
Engr 4862 Microprocessors
Input / Output Instructions
• For 8-bit port
IN AL, Port #
OUT Port #, AL
MOV DX, Port #
IN AL, DX
MOV DX, Port #
OUT DX, AL
• For 16-bit port
IN AX, Port #
OUT Port #, AX
MOV DX, Port #
IN AX, DX
MOV DX, Port #
OUT DX, AX
Engr 4862 Microprocessors
Input / Output Instructions
• Since 8086/88 has a 16-bit data bus internally,
it is capable of transferring 16-bit data to or
from AX.  This requires having two port
addresses, one for each byte!
• Example: AX = 9876H, Port # = 40H
OUT 40H, AX
 Port 40  76H (AL), Port 41  98H(AH)
• For 8086, takes one bus cycle to complete the
transfer, for 8088, two bus cycles are required
Engr 4862 Microprocessors
Output Design Example: 8 LEDs
• This is a byte-wide output port
• The LEDs cannot be connected directly to
data bus
– Difficult to select the LEDs
– LEDs would only display value for very short
period of time (about 400ns, or 2 clock cycles)
• Only when data bus carries the correct signal
– Microprocessor cannot sink enough current
Engr 4862 Microprocessors
Example: 8 LEDs
• Instead, we need to capture the values on
the data bus, and hold them until changed
– The 74LS373 octal latch will do nicely
8088
Data bus
74LS373
Engr 4862 Microprocessors
Example: 8 LEDs
• We only want the latch to load values from
the data bus when the microprocessor
outputs to the correct port #
– Suggestion 1: Decode the address directly
– Suggestion 2: Use a decoder such as the 3x8
74LS138 with lines from the address bus
Engr 4862 Microprocessors
Example: 8 LEDs
D0
74LS373
Q0
D Q
Latch Out
System Data Bus
D7
System Address
Bus
Q7
G
OC
IOW
Engr 4862 Microprocessors
Example: 8 LEDs
8088
Address
bus
74LS373
Data bus
74LS138
Note: This is not quite enough!
Engr 4862 Microprocessors
Example: 8 LEDs
• How do we connect the LEDs?
– 2 possibilities
Engr 4862 Microprocessors
Example: 8 LEDs
+ 5V
LS373
LS373
Engr 4862 Microprocessors
+ 5V
Example: 8 LEDs
+ 5V
The 74LS373 does not have
enough power to drive an LED.
LS373
The device can sink enough
current for the LED to light
(15 to 20 mA).
180ohms
Engr 4862 Microprocessors
+ 5V
Bus Cycles for outputting
• Assume the port address is 99H  OUT 99H, AL
– T1: address 99H is provided to address bus A0 – A7
through AD0 – AD7 and ALE signal
– T2: IOW is provided and the contents of AL are
released into the data bus pins AD0 – AD7
– T3: signal propagates to the destination port
– T4: the content of AL are latched into the 74LS373 with
the IOW going from low to high
Engr 4862 Microprocessors
Example: 8 Switches
• Now we will look at an 8-bit input port.
• The procedure to select the port is similar to
the output case
– Use IORD* instead of IOWR*
Engr 4862 Microprocessors
Example: 8 Switches
• We cannot use a latch to separate the
switches from the microprocessor
– We only want the switch values to be on the
data bus when the microprocessor asks for it
– A latch would constantly drive the bus!
Engr 4862 Microprocessors
Example: 8 Switches
• The device of interest here is the 74LS244
tristate buffer (unidirectional)
– NOT the same as the 74LS245 transceiver
(bidirectional)
• Tristate:
– One of three states: on (1), off (0), or open (Z)
– In the open state, the buffer does not drive the
data bus
Engr 4862 Microprocessors
Example: 8 Switches
• How do we set up the switches?
– When open, one logic level
– When closed, the other logic level
Engr 4862 Microprocessors
Example: 8 Switches
+ 5V
10K ohms
LS244
Engr 4862 Microprocessors
Example: 8 Switches
74LS244
Q0
D0
Switches
To System Data
Bus
D4
D7
System Address
Bus
Q7
G1
IOR
Engr 4862 Microprocessors
G2
Summary
• Since the data provided by the CPU to the port is on the
system data bus for a limited amount of time (501000ns), it must be latched before it is lost
• In order to prevent any unwanted data from coming into
the system data bus, all input devices must isolated
through the tri-state buffer
– The 74LS244 not only plays this role, but also provides the
incoming signals sufficient strength (boosting) to travel all the
ways to the CPU.
• As general, every device (memory, peripherals)
connected to the global data bus must have a latch ot tristate buffer
Engr 4862 Microprocessors
Programmable I/O
• The previous examples are good for many
applications, but sometimes a more powerful
and flexible solution is needed.
• The 8255 Programmable Peripheral Interface
(PPI) is a 40-pin DIP IC that provides 3
programmable I/O ports, A, B, and C.
• One can program the individual port to be input
or output port, economical and flexible than
74LS373, 73LS244, which must be hard wired)
Engr 4862 Microprocessors
Programmable I/O
• How are is it programmable?
– Configure each port as input or output
– Different modes of operation
• You must initialize the PPI via software
commands
– Send a control byte to the device’s control
register port
Engr 4862 Microprocessors
Pin Description
• PA0 – PA7: Port A / All / input/output/bidirectional
• PB0 – PB7: Port B / All / input/output
• PC0 – PC7: Port C / All / input/output
Can be split into two parts: Upper (PC7 – PC4)
and Lower (PC3 – PC0).
Each can be used for input or output.
Any of PC0 – PC7 can be programmed.
• RD and WR: control signal input to 8255
IOR and IOW in peripheral I/O
MEMR and MEMW in memory-mapped I/O
Engr 4862 Microprocessors
Pin Description
• RESET: Active high input signal to 8255
– Used to clear the internal control register
– When activated, all ports are initialized as input ports.
– Usually connect to the RESET output of the system bus or
ground
• A0, A1, and CS
– CS selects the entire chip, A0 and A1 select the specified port
– Used to access port A, B, C,
CS A1 A0 Select
or control register
0
0
0
Port A
0
0
1
Port B
0
1
0
Port C
0
1
1
Control Reg.
1
x
x
Not Selected
Engr 4862 Microprocessors
Control Word of 8255
D7 D6 D 5 D4 D3 D2 D1 D0
Group B
Port C Lower PC3-PC0
1 = input, 0 = output
Port B
1 = input, 0 = output
Mode Selection
0 = Mode0, 1 = Mode1
Group A
Port C Upper PC7-PC4
1 = input, 0 = output
Port A
1 = input, 0 = output
Mode Selection
00 = Mode0, 01 = Mode1
1x = Mode 2
Engr 4862 Microprocessors
1 = I / O Mode
0 = BSR Mode
Mode Selection
• It’s the control register that must be
programmed to select the operation mode
of the three ports: A, B, and C
• The 8255 chip is programmed in any of the
above modes by sending a byte (control
word) to the control register of the 8255
Engr 4862 Microprocessors
Mode Selection
• Mode 0: simple I/O
– Any ports: A, B, CL, CU. No control of individual bits
• Mode 1: I/O (ports A and B) with handshaking (port C)
– Synchronizes communication between an intelligent device
(printer)
• Mode 2: Bi-directional I/O with handshaking
– Port A: bidirectional I/O with handshaking through port C
– Port B: Simple I/O or in handshake mode 1
• BSR Mode: Bit set/reset
– Only the individual bits on Port C can be programmed
Engr 4862 Microprocessors
8255 Design Example
A2
System Address
Bus
D0
D0
D7
D7
IOW
IOR
WR
RD
A0
A1
A0
A1
CS
A7
Engr 4862 Microprocessors
A
B
CL
CH
8255 Design Example
• Mode 0
– Any of ports A, B, C can be programmed as input or
output
– Port can not be both an input and output port at the
same time
– Port C can be programmed with CL, CH separately
– Example:
Engr 4862 Microprocessors