CHAPTER 33) ALTERNATING-CURRENT CIRCUITS 33.1 : AC SOURCES AND PHASORS • An ac circuit consists of circuit elements and a generator that.

Download Report

Transcript CHAPTER 33) ALTERNATING-CURRENT CIRCUITS 33.1 : AC SOURCES AND PHASORS • An ac circuit consists of circuit elements and a generator that.

CHAPTER 33) ALTERNATING-CURRENT CIRCUITS
33.1 : AC SOURCES AND PHASORS
• An ac circuit consists of circuit elements and a generator that provides athe
alternating current.
• When a conducting loop is rotated in a magnetic field at constant angular
frequency , a sinusoidal voltage (emf) is induced in the loop.
  Vmax sin t
• This instantaneous voltage  is :
where Vmax is the
maximum output voltage of the ac generator, or the voltage amplitude.
• The angular frequency is :
  2f 
2
T
where f is the frequency of the
generator (the voltage source) and T is the period.
• Because the output voltage of an ac generator varies sinusoidally with time, the
voltage is positive during one half of the cycle and negative during the other
half.
• If an ac generator is connected to a series circuit containing resistors, inductors,
and capacitors – we want to know the amplitude and time characteristics of
the alternating current.
• Phasor diagrams – graphical constructions to simplify our analysis of circuits
containing two or more elements.
• In phasor diagram, alternating (sinusoidal) quantities, such as current and
voltage, are represented by rotating vectors called phasors.
• The length of the phasor represents the amplitude (macimum value) of the
quantity, and the projection of the phasor onto the vertical axis represents the
instantaneous value of the quantity.
33.2 : RESISTORS IN AN AC CIRCUIT
• Consider a simple ac circuit consisting of a resistor and an ac generator
as shown in Figure (33.1).
,
• At any instant, the algebraic sum of the voltages around a closed loop in a
circuit must be zero (Kirchhoff’s loop rule).
• Therefore,  - R = 0, or :
   R  Vmax sin t
where R is the instantaneous voltage across the resistor.
(33.1)
• Therefore, the instantaneous current in the resistor is :
iR 
 R Vmax

sin t  I max sin t
R
R
(33.2)
where Imax is the macimum current :
I max 
Vmax
R
(Maximum current in a resistor)
• From Equations (33.1) and (33.2), we see that the instantaneous voltage across
the resistor is :
R  ImaxR sin t
(33.3)
Figure (33.2a)
• Let us discuss the current-versus-time curve shown in Figure (33.2a).
• At point a, the current has a maximum value in one direction, arbitrarily called
the positive direction.
• Between points a and b, the current is decreasing in magnitude but is still in the
positive direction.
• At b, the current is momentarily zero; it then begins to increase in the negative
direction between points b and c.
• At c, the current has reached its maximum value in the negative direction.
• Refering to Figure (33.2a) – the current and voltage are in step with each other
because they vary identically with time.
• Because iR and R both vary as sin t and reach their maximum values at the
same time, they are said to be in phase.
• Thus, for a sinusoidal applied voltage, the current in a resistor is always in phase
with the voltage across the resistor.
Figure (33.2b)
• A phasor diagram is used to represent current-voltage phase relationships.
• The lengths of the arrows correspond to Vmax and Imax.
• The projections of the phasor arrows onto the vertical axis give R and iR
values.
• If the phasor arrow is imagined to rotate steadily with angular speed , its
vertical-axis component oscillates sinusoidally in time.
• In case of the singel-loop resistive circuit of Figure (33.1), the current and
voltage phasors lie along the same line, because iR and R are in phase.
• The rate at which electrical energy is converted to internal energy in a resistor is
the power P = i2 R, where i is the instantaneous current in the resistor.
• Alternating current is at the maximum value for only an instant during each
cycle (Figure (33.3a)).
• What is of importance in an ac circuit is an average value of current; refereed to
as the rms current.
• rms = root mean square, which in this case means the square root of the mean
(average) value of the square of the current :
I rms  i 2
• Because i2 varies as sin2t and because the average value of i2 is :
1 2
I max (refer Figure (33.3b)), the rms current is :
2
I rms 
I max
 0.707I max
2
(33.4)
rms current
• This equation states that an alternating current whose maximum value is 2.00 A
delivers to a resistor the same power as a direct current that has a value of
(0.707)(2.00A) = 1.41 A.
• Thus, we can say that the average power delivered to a resistor that carries an
alternating current is :
Pav  I 2rmsR
Average power delivered to a resistor
i
i2
Imax
i 2max
t
(a)
i 2  12 I2max
FIGURE (33.3)
t
(b)
• Alternating voltage also is best discussed in terms of rms voltage, and the
relationship is identical to the at for current :
Vrms 
Vmax
 0.707Vmax
2
(33.5)
rms voltage
• When we speak of measuring a 120-V alternating voltage from an electrical
outlet, we are refering to an rms voltage of 120 V.
• Using Eq. (33.5), an alternating voltage has a maximum value of about 170 V.
Example (33.1) : What is the rms current ?
The voltage output of a generator is given by  = (200V) sin t. Find the rms
current in the circuit when this generator is connected to a 100- resistor.
What is the maximum current in the circuit.
Solution
• Comparing this expression for voltage output with the general form  =
Vmax sin t, wee see that Vmax = 200 V. Thus, the rms voltage is :
Vrms 
• Therefore,
I rms 
Vmax 200V

 141V
2
2
Vrms 141V

 1.41A
R
100 
• The maximum current in the circuit : Irms  0.707Imax
I max 
1.41
 2A
0.707
33.3) INDUCTORS IN AN AC CIRCUIT
• Consider an ac circuit consisting only of an inductor connected to the terminals
of an ac generator (Figure (33.4)).
• If L =L=-L(di/dt) is the self-induced instantaneous voltage across the
inductor, then the Kirchhoff’s loop rule applied to this circuit gives
 + L = 0, or :
di
  L  0
dt
• Substitute Vmax sin t for  and rearrange, we obtain :
L
di
 Vmax sin t
dt
• Solving this equatiion for di, we find that :
di 
Vmax
sin tdt
L
(33.6)
 L
L
  Vmax sin t
FIGURE (33.4)
• Integrating this expression gives the instantaneous current in the inductor as a
function of time :
iL 
Vmax
Vmax
sin

tdt


cos t

L
L
(33.7)
• Using the trigonometric identity  cos t = - sin (t - /2), we can express Eq.
(33.7) as :
Vmax 

iL 
sin  t  
L
2

(33.8)
• Comparing this result with Equation (33.6), we see that the instantaneous
current iL in the inductor and the instantaneous voltage L across the inductor
are out of phase by (/2) rad = 90o.
Figure (33.5)
• Inductors in an ac circuit produce a current that is out of phase with the ac
voltage.
• At point a, the current begins to increase in the positive direction.
• At this instant the rate of change of current is at a maximum, and thus the voltage
across the inductor is also at a maximum.
• As the current increases between points a and b, di/dt (the slope of the current
curve) decreases until it reaches zero at point b.
• As a result, the voltage across the inductor is decreasing during this same time
interval, as the curve segment between c and d indicates.
• Immediately after point b, the current begins to decrease, although it still has the
same direction it had during the previous quarter cycle (from a to b).
• As the current decreases to zero (from b to e), a voltage is again induced in the
inductor (d to f), but the polarity of this voltage is opposite that of the voltage
induced between c and d (because back emfs are always directed to oppose the
change in the current).
• The voltage reaches its maximum value one quarter of a period before the
current reaches its maximum value.
• Thus, we see that : for a sinusoidal applied voltage, the current in an inductor
always lags behind the voltage across the inductor by 90o (one-quarter cycle in
time).
• Figure (33.5b) – shows the phasor diagram for the inductive circuit of Figure
(33.4).
• From Eq. (33.7) – the current in an inductive circuit reaches its maximum value
when cost = - 1 :
I max 
Vmax Vmax

L
XL
(33.9) Maximum current in an inductor
where the quantity XL, called the inductive reactance, is :
X L  L
(33.10)
Inductive reactance
• Equation (33.() indicates that, for a given applied voltage, the maximum current
decreases as the inductive reactance increases.
• The expression fo the rms current in an inductor is similar to Equation (33.9) :
I rms
Vrms Vrms


L
XL
• Inductive reactance in an ac circuit
 has units of ohms.
 depends on frequency and the characteristics of the inductor.
 increase as the frequency of the current increases, because at higher
frequencies, the instantaneous current must change more rapidly than it does at
the lower frequencies; this causes an increase in the maximum induced emf
associated with a given maximum current.
• The instanteneous voltage across the inductor is :
di
 L  L  Vmax sin t  I maxX L sin t
dt
(33.11)
Example (33.3) : A Purely Inductive ac Circuit
In a purely inductive ac circuit (see Figure (33.4), L = 25.0 mH and the rms
voltage is 150 V. Calculate the inductive reactance and rms current in the circuit
if the frequency is 60.0Hz.
Solution
• Equation (33.10) gives :
XL  L  2fL  2(60.0Hz)(25.0 103 H)  9.42
• From a modified version of Equation (33.9),
the rms current is:
I rms 
VL,rms
XL
 L
L
150V

 15.9A
9.42
  Vmax sin t
FIGURE (33.4)
33.4) CAPACITORS IN AN AC CIRCUIT
• Figure (33.7) – shows an ac circuit consisting of a capacitor connected across
the terminals of an ac generator.
• Kirchhof’s loop rule applied to this circuit gives  - C = 0, or
  C  Vmax sin t
(33.12)
• Where C is the instantaneous voltage across the capacitor.
• From the definition of capacitance; C = q/ C;
hence, Equation (33.12) gives :
C
C
q  CVmax sin t
(33.13)
where q = the instantaneous charge on the
capacitor.
  Vmax sin t
FIGURE (33.7)
• Because i = dq/dt, differentiating Equation (33.13) gives the instantaneous
current in the circuit :
iC 
dq
 CVmax cos t
dt
• Using the trigonometric identity :
(33.14) in the alternative form :
(33.14)


cost  sin t  
2



i C  CVmax sin  t  
2

we can express Eq.
(33.15)
Figure (33.8)
• The current is /2 rad = 90o out of phase with the voltage across the capacitor.
• Fig. (33.8a) - a plot of current and voltage versus time – shows that the current
reaches its maximum value one quarter of a cycle sooner than the voltage
reaches its maximum value.
• The segment of the current curve from a to b indicates that the current starts out
at a relatively high value.
• There is no charge on the capacitor at t=0  nothing in the circuit except the
resistance of the wires can hinder the flow of charge at this instant.
• The current decreases as the voltage across the capacitor increases (from c to d
on the voltage curve), and the capacitor is charging.
• When the voltage is at point d, the current reverses and begins to increase in the
opposite direction (from b to e on the current curve).
• During this time, the voltage across the capacitor decreases from d to f because
the plates arenow losing the charge they accumulated earlier.
• During the second half of the cycle, the current is initially at its maximum value
in the opposite direction (point e) and thendecreases as the voltage across the
capacitor builds up.
• Figure (33.8b) – shows the phasor diagram, and also shows that : for a
sinusoidally applied voltage, the current in a capacitor always leads the
voltage across the capacitor by 90o.
• From equation (33.14), we see that the current I the circuit reaches its maximum
value when cos t = 1 :
I max  CVmax
Vmax

XC
(33.16)
where XC is called the capacitive reactance :
XC 
1
C
(33.17)
Units : ohms
• The rms current is given by :
I rms  CVrms 
Vrms
XC
• Combining Eq. (33.12) and (33.16), we can express the instantaneous voltage
across the capacitor as :
C  Vmax sin t  ImaxXC sin t
(33.18)
• Equations (33.16) and (33.17) indicate that as the frequency of the voltage
source increases, the capacitive reactance decreases and therefore the
maximum current increases.
• The frequency of the current is determined by the frequency of the voltage
source driving the circuit.
• As the frequency approaches zero, the capacitive reactance approaches
infinity, and hence the current approaches zero, because the circuit approaches
direct-current conditions as  approaches 0.
Example (33.4) : A Purely Capacitive ac Circuit
An 8.00-F capacitor is connected to the terminals of a 60.0-Hz ac generator
whose rms voltage is 150 V. Find the capacitive reactance and the rms current in
the circuit.
Solution
Using Equation (33.17) and the fact that  = 2f = 377 s-1 gives :
XC 
1
1

 332
1
6
C (377s )(8.0010 F)
Hence, from a modified Equation (33.16), the rms current is :
I rms 
Vrms 150V

 0.452A
XC
332
33.5) THE RLC SERIES CIRCUIT
• Figure (33.9a) – shows a circuit that contains a resistor, an inductor, and a
capacitor connected in series across an alternating-voltage source.
• The instantaneous applied voltage is given by :
while the current varies as :
  Vmax sin t
i  Imax sin(t  )
where  is the phase angle between the current and the applied voltage.
• Aim – to determine  and Imax.
• Fig. (33.9b) – shows the voltage versus time across each element in the circuit
and their phase relationships.
 R
 L
C
R
L
C
FIGURE (33.9a)
Phasor diagram (Figure (33.10))
• Because the elements are in series, the current everywhere in the circuit must
be the same at any instant.
• That is, the current at all points in a series ac circuit has the same amplitude
and phase.
• Therefore, the voltage across each elemetn has a different amplitude and phase.
• The voltage across the resistor is in phase with the current, the voltage across
the inductor leads the current by 90o, and the voltage across the capacitor lags
behind the current by 90o.
• Using the phase relationships, we can express the instantaneous voltages across
the three elements as :
 R  I maxR sin t  VR sin t
(33.19)


 L  I maxX L sin t    VL cost
2

(33.20)


 C  I maxX C sin  t    VC cost
2

(33.21)
where VR, VL, and VC are the maximum voltage values across the
elements:
VR  ImaxR
VL  ImaxXL
VC  I maxXC
• The instantaneous voltage  across the three elements equals the sum :
   R   L  C
Obtaining the sum () by examining the phasor diagram :
VL
Vmax
VL  VC


VC
(a)
Vmax
I max VR

FIGURE (33.11)
(b)
VR
• Because the current at any instant is the same in all elements, we can obtain a
phasor diagram for the circuit.
• Combine the three phasor pairs in Figure (33.10) to obtain Figure (33.11a), in
which a single phasor Imax is used to represent the current in each element.
• To obtain the vector sum of the three voltage phasors in Figure (33.11a), we
redraw the phasor diagram as in Figure (33.11b). From this diagram, we see that
the vector sum of the voltage amplitudes VR, VL, and VC equals a phasor
whose length is the maximum applied voltage Vmax, where the phasor Vmax
makes an angle  with the current phasor Imax.
• The voltage phasors VL and VC are in opposite directions along the same
line, and hence we can construct the difference phasor VL - VC, which is
perpendicular to the phasor VR.
• From either one of the right triangles in Figure (33.11b), we see that :
Vmax  VR2  (VL  VC ) 2  (I maxR ) 2  (I maxX L  I maxX C ) 2
Vmax  I max R 2  (X L  X C ) 2
(33.22)
• Therefore, we can express the maximum current as :
I max 
Vmax
R 2  (X L  X C ) 2
• The impedance Z of the circuit is defined as :
Z  R 2  (X L  X C ) 2
(33.23)
Units = ohms
• Equation (33.22) can be written in the form :
Vmax  I maxZ
(33.24)
• We can regard Equation (33.24) as the ac equivalent of Equation (27.8), which
defined resistance in a dc circuit as the ratio of the voltage across a conductor to
the current in that conductor.
• The impedance and the current in an ac circuit depend upon the resistance, the
inductance, the capacitance, and the frequency (bexause the reactances are
frequency-dependent).
• Removed the common factor Imax from each phasor in Figure (33.11a) – we can
construct the impedance triangle shown in Figure (33.12).
• From this phasor diagram we find that the phase angle  between the current
and the voltage is :
 X  XC 
(33.25)
  tan1  L


R

• From Figure (33.12) – cos = R/Z.
• When XL > XC (which occurs at high
frequencies), the phase angle is positive
– the current lags behind the applied
voltage (Figure (33.11a)).
Z
X L  XC
• When XL < XC, the phase angle is
negative – the current leads the applied
voltage.

• When XL = XC, the phase angle is zero.
FIGURE (33.12)
• In this case – the impedance equals the
resistance and the current has its
maximum value, given by Vmax / R.
R
• The frequency at which this occurs is called the resonance frequency.
• Table 33.1 gives impedance values and phase angles for various series circuits
containing different combinations of elements (ac voltage).
Circuit Elements
R
C
L
R
C
R
R
L
L
Phase Angle 
Impedance Z
C
R
00
XC
- 90o
XL
+ 900
R 2  X C2
Negative,
between –90o and 0o
R 2  X 2L
Positive,
Between 0o and 90o
R 2  (X L  X C ) 2
Negative if XC > XL
Positive if XC < XL
Example (33.5) : Finding L from a Phasor Diagram
In a series RLC circuit, tha applied voltage has a maximum value of 120V and
oscillates at a frequency of 60.0Hz. The circuit contains an inductor whose
inductance can be varied, a 200- resistor, and a 4.00-F capacitor. What value
of L should an engineer analyzing the circuit choose such that the voltage across
the capacitor lags the applied voltage by 30.0o?
Solution
• The phase relationships for the drops in voltage across the elements are shown
in Figure (33.14).
• From the figure we see that the phase angle is  = - 60.0o.
• This is because the phasors representing Imax and VR are in the same direction
(they are in phase).
• From Equation (33.25), we find that :
XL  XC  R tan
• Substituting Equations (33.10) and (33.17) (with  = 2 f) into this expression
gives :
2fL 
L
1
 R tan 
2fC
1
2f
 1


R
tan

 2fC

• Substituting the given values into the equation gives L = 0.84 H.
VL

VR
FIRGURE (33.14)
30.0o
VC
Vmax
Exampel (33.6) : Analyzing a Series RLC Circuit
A series RLC ac circuit has R=425, L=1.25H, C=3.50F, =377s-1, and
Vmax=150V.
(a) Determine the inductive reactance, the capacitive reactance, and the
impedance of the circuit.
Solution
The rectances are :
XL=L=471
and
The impedance is :
Z  R 2  (X L  X C ) 2
 (125) 2  (471  758) 2
 513
(b) Find the maximum current in the circuit.
Solution
I max 
Vmax 150 V

 0.292 A
Z
513
XC=1/C=758 .
(c) Find the phase angle between the current and voltage.
Solution
 X  XC 
1  471  758 
o
  tan1  L
  tan 
  34.0
R
425




Because the circuit is more capacitive than inductive,  is negative and the
current leads the applied voltage.
(d) Find both the maximum voltage and the instantaneous voltage across each
element.
Solution
The maximum voltages are :
VR  I maxR  (0.292A)(425)  124V
VL  I maxX L  (0.292A)(471)  138V
VC  I maxX C  (0.292A)(758)  221V
Using Equation (33.19), (33.20), and (33.21), we find that we can write the
instantaneous voltages across the three elements as :
 R  (124V) sin 377t
 L  (138V) cos377t
 C  (221V) cos377t