Transcript ITEC TRAINING This training session will explain how to use ITEC equipment and support learning in the classroom setting. Presented by: R.

ITEC TRAINING
This training session will explain how to use ITEC
equipment and support learning in the classroom setting.
Presented by: R. Schmid
TABLE OF CONTENTS
The intended use of this tutorial is to help you learn how to
use all of the ITEC Equipment on SJFC campus.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
LCD Projector
Select audio/video source
Power Screen
Volume Control
Picture Mute
DVD/VCR Control Panel
Document Camera
Laptop setup
Touch Screen Panel
OIT Help Desk
STEP 1: TURN ON LCD PROJECTOR

From the control panel, within the Display Section, press the ON or OFF
button.

Button will flash while it is warming up or cooling down.

Flashing stops, LCD projector is ready for use—select a source to display.
** Remember to turn off the projector when
finished using**
STEP 3: POWERED PROJECTION SCREEN

In classrooms with a powered projection screen, the
screen control switch can be located on the wall
behind the presenter’s station.
STEP 4: VOLUME CONTROL
Use the volume knob on the control panel to adjust
the volume of the selected device.
 Troubleshooting steps….

NO SOUND ???

If using a PC or Laptop:
From the task bar, click on the sound icon
 Ensure that Mute isn’t checked
 Raise or lower the volume control bar to adjust the sound

WHAT IS PICTURE MUTE?
To mute or “hide” what is being displayed through the
projector.
 Press the PIC MUTE button, located in the middle of
the control panel.

DVD/ VCR CONTROL PANEL

After selecting DVD or VCR as your source, use this
control panel just like you would a remote control.
STEP 2: DISPLAY DEVICE THROUGH LCD PROJECTOR

From the input button section, select device to be displayed.
Showing a DVD
to your class,
press the DVD
button
CHOOSE A MODEL

Three different models on campus, click on the picture
for instructions.
STEP 1 OF 4: POWER ON
Power on, hold down button until the red light
flashes.
 Ready to use when the light turns green.

Back
Step 2
STEP 2 OF 4: SELECT DOC CAM AS
SOURCE

From the control panel, press the DOC CAM
button.
Back
Step 3
STEP 3 OF 4: FOCUS AND ZOOM



Press the AF button to Auto Focus
Digital Zoom  press the Zoom + or – button
Manual Zoom raise the camera neck to position the camera
Back
Step 4
STEP 4 OF 4: POWER OFF

Hold down the Power button until the green light
flashes, light turns red when the document camera
is off.
Back
Choose a model
STEP 1 OF 4: POWER ON
Slide the POWER button up or down.
 Ready to use when the light is on.

Back
Step 2
STEP 2 OF 4: SELECT DOC CAM AS SOURCE

From the control panel, press the DOC CAM
button.
Back
Step 3
STEP 3 OF 4: ZOOM

Digital Zoom  sliding your finger across the zoom
wheel, you can zoom in or out.
Back
Step 4
STEP 4 OF 4: POWER OFF

Slide the Power button down to turn off.
Back
Choose a model
STEP 1 OF 4: POWER ON
Power on, hold down button until the red light
flashes.
 Ready to use when the light turns green.

Back
Step 2
STEP 2 OF 4: SELECT DOC CAM AS SOURCE

From the control panel, press the DOC CAM
button.
Back
Step 3
STEP 3 OF 4: ZOOM AND BRIGHTNESS


Press the Zoom + or – button to zoom in or out.
With the arm lights on, press the Brightness + or – button.
Back
Step 4
STEP 4 OF 4: POWER OFF
Hold down the Power button until the green light
flashes.
 The document camera is off when the light turns red.

Back
Choose a model
HOW DO I CONNECT A LAPTOP?
Attach the VGA and audio cables if necessary to your
laptop.
 Enable the Monitor Out Function on your laptop

MONITOR OUT FUNCTION
On your laptop use the “Monitor Out” key in
conjunction with the Function Button (Fn).
 The Monitor Out key is usually labeled with a
“||”symbol or says CRT/LCD” and is usually the F4,
F5, or F8 key

TOUCH SCREEN PANEL


The projector will power on once a source is selected. All
sources are located on the left of the touch screen.
Note: The projector will take about 30 seconds for the lamp
to warm up.
Volume
Sources
Help
NEED ASSISTANCE – CONTACT HELP DESK

Contact the OIT Help Desk




By phone: 385-8016 –please feel free to leave a message
By e-mail: [email protected]
In person: Kearney 053 (adjacent to the computer lab)
ITEC classrooms on SJFC campus- View pictures
and instructions online at
http://oit.sjfc.edu/Labs/lab_intro.asp