Transcript IP Addressing & Subnetting Made Easy Developed by Peter Smith [email protected] Working with IP Addresses Peter Smith.

IP Addressing &
Subnetting Made Easy
Developed by Peter
Smith
[email protected]
Working with IP
Addresses
Peter Smith
Introduction
You can probably work with decimal
numbers much easier than with the
binary numbers needed by the
computer.
 Working with binary numbers is timeconsuming & error-prone.

Peter Smith
3
Octets
The 32-bit IP address is broken up into
4 octets, which are arranged into a
dotted-decimal notation scheme.
 An octet is a set of 8 bits & not a
musical instrument.
 Example of an IP version 4:
172.64.126.52

Peter Smith
4
Thinking in Binary
 The
binary system uses only 2
values “0 & 1” to represent
numbers in positions representing
increasing powers of 2.
 We all are accustomed to thinking
& working in the decimal system,
which is based on the number 10.
Peter Smith
5
Thinking in Binary (Cont.)
 To
most humans, the number 124
represents 100 + 20 + 4.
 To the computer, this number is
1111100, which is 64 (26) + 32 (25)
+ 16 (24) + 8 (23) + 4 (22) + 0 + 0
Peter Smith
6
 Each
position in a binary number
represents, right to left, a power of
two beginning with 20 & increasing
by one power as it moves left: 20,
21, 22, 24, etc.
Peter Smith
7
Converting to Decimal
You’ll need to convert binary to
decimal & vice versa to compute
subnets & hosts.
 So, it’s time for a quick review lesson in
binary-to-decimal conversion.
 There are 8 bits in an octet & each bit
can only be a 1 or a 0.

Peter Smith
8
Converting to Decimal (Cont.)

What then do you suppose is the largest
decimal number that can be expressed
in an octet?
Eight 1’s (1111 1111)
Peter Smith
9
Converting to Decimal (Cont.)

Now, for double the money, what is its
equivalent decimal value?
27
26
25
24
23
22
21
20
1
1
1
1
1
1
1
1
128
64
32
16
8
4
2
1
The binary number 1111 1111 converts into the
decimal number:
128 + 64 + 32 + 16 + 8 + 4 + 2 + 1 = 255
Peter Smith
10
Converting to Decimal (Cont.)
Therefore, the largest decimal number
that can be stored in an IP address octet
is 255.
 The significance of this should become
evident later in this presentation.

Peter Smith
11
IP Address Classes
IP addresses are divided into 5 classes,
each of which is designated with the
alphabetic letters A to E.
 Class D addresses are used for
multicasting.
 Class E addresses are reserved for
testing & some mysterious future use.

Peter Smith
12
IP Address Classes (Cont.)

Peter Smith
The 5 IP classes are split up based on
the value in the 1st octet:
13
IP Address Classes (Cont.)
Using the ranges, you can determine the
class of an address from its 1st octet
value.
 An address beginning with 120 is a
Class A address, 155 is a Class B
address & 220 is a Class C address.

Peter Smith
14
Are You the Host or the
Network?

The 32 bits of the IP address are divided into
Network & Host portions, with the octets
assigned as a part of one or the other.
Network & Host Representation
By IP Address Class
Class
Peter Smith
Octet1
Octet2
Octet3
Octet4
Class A
Network
Host
Host
Host
Class B
Network
Network
Host
Host
Class C
Network
Network
Network
Host
15
Are You the Host or the
Network? (Cont.)
Each Network is assigned a network
address & every device or interface
(such as a router port) on the network is
assigned a host address.
 There are only 2 specific rules that
govern the value of the address.

Peter Smith
16
Are You the Host or the
Network? (Cont.)
A host address cannot be designated by
all zeros or all ones.
 These are special addresses that are
reserved for special purposes.

Peter Smith
17
Class A Addresses
Class A IP addresses use the 1st 8 bits
(1st Octet) to designate the Network
address.
 The 1st bit which is always a 0, is used
to indicate the address as a Class A
address & the remaining 7 bits are used
to designate the Network.
 The other 3 octets contain the Host
address.

Peter Smith
18
Class A Addresses (Cont.)

Peter Smith
There are 128 Class A Network
Addresses, but because addresses with
all zeros aren’t used & address 127 is a
special purpose address, 126 Class A
Networks are available.
19
Class A Addresses (Cont.)


Peter Smith
There are 16,777,214 Host addresses
available in a Class A address.
Rather than remembering this number
exactly, you can use the following formula to
compute the number of hosts available in any
of the class addresses, where “n” represents
the number of bits in the host portion:
(2n – 2) = Number of available hosts
20
Class A Addresses (Cont.)




Peter Smith
For a Class A network, there are:
224 – 2 or 16,777,214 hosts.
Half of all IP addresses are Class A
addresses.
You can use the same formula to determine
the number of Networks in an address class.
Eg., a Class A address uses 7 bits to
designate the network, so (27 – 2) = 126 or
there can be 126 Class A Networks.
21
Class B IP Addresses
Class B addresses use the 1st 16 bits
(two octets) for the Network address.
 The last 2 octets are used for the Host
address.
 The 1st 2 bit, which are always 10,
designate the address as a Class B
address & 14 bits are used to designate
the Network. This leaves 16 bits (two
octets) to designate the Hosts.

Peter Smith
22
Class B IP Addresses (Cont.)
So how many Class B Networks can
there be?
 Using our formula, (214 – 2), there can
be 16,382 Class B Networks & each
Network can have (216 – 2) Hosts, or
65,534 Hosts.

Peter Smith
23
Class C IP Addresses

Peter Smith
Class C addresses use the 1st 24 bits
(three octets) for the Network address
& only the last octet for Host
addresses.the 1st 3 bits of all class C
addresses are set to 110, leaving 21 bits
for the Network address, which means
there can be 2,097,150 (221 – 2) Class C
Networks, but only 254 (28 – 2) Hosts
per Network.
24
Class C IP Addresses (Cont.)
Peter Smith
25
Special Addresses
A few addresses are set aside for
specific purposes.
 Network addresses that are all binary
zeros, all binary ones & Network
addresses beginning with 127 are
special Network addresses.

Peter Smith
26
Special Addresses (Cont.)
Peter Smith
27
Special Addresses (Cont.)

Peter Smith
Within each address class is a set of
addresses that are set aside for use in
local networks sitting behind a firewall
or NAT (Network Address Translation)
device or Networks not connected to
the Internet.
28
Special Addresses (Cont.)

Peter Smith
A list of these addresses for each IP
address class:
29
Subnet Mask

An IP address has 2 parts:




Peter Smith
The Network identification.
The Host identification.
Frequently, the Network & Host portions of
the address need to be separately extracted.
In most cases, if you know the address class,
it’s easy to separate the 2 portions.
30
Subnet Mask (Cont.)


Peter Smith
With the rapid growth of the internet & the
ever-increasing demand for new
addresses, the standard address class
structure has been expanded by borrowing
bits from the Host portion to allow for
more Networks.
Under this addressing scheme, called
Subnetting, separating the Network &
Host requires a special process called
Subnet Masking.
31
Subnet Mask (Cont.)



Peter Smith
The subnet masking process was
developed to identify & extract the
Network part of the address.
A subnet mask, which contains a binary
bit pattern of ones & zeros, is applied to
an address to determine whether the
address is on the local Network.
If it is not, the process of routing it to an
outside network begins.
32
Subnet Mask (Cont.)



Peter Smith
The function of a subnet mask is to
determine whether an IP address exists on
the local network or whether it must be
routed outside the local network.
It is applied to a message’s destination
address to extract the network address.
If the extracted network address matches
the local network ID, the destination is
located on the local network.
33
Subnet Mask (Cont.)
However, if they don’t match, the
message must be routed outside the
local network.
 The process used to apply the subnet
mask involves Boolean Algebra to filter
out non-matching bits to identify the
network address.

Peter Smith
34
Boolean Algebra


Peter Smith
Boolean Algebra is a process that applies
binary logic to yield binary results.
Working with subnet masks, you need
only 4 basic principles of Boolean
Algebra:
 1 and 1 = 1
 1 and 0 = 0
 0 and 1 = 0
 0 and 0 = 0
35
Boolean Algebra (Cont.)
In another words, the only way you can
get a result of a 1 is to combine 1 & 1.
Everything else will end up as a 0.
 The process of combining binary values
with Boolean Algebra is called Anding.

Peter Smith
36
Default Standard Subnet
Masks

Peter Smith
There are default standard subnet masks
for Class A, B and C addresses:
37
A Trial Separation
Subnet masks apply only to Class A, B
or C IP addresses.
 The subnet mask is like a filter that is
applied to a message’s destination IP
address.
 Its objective is to determine if the local
network is the destination network.

Peter Smith
38
A Trial Separation (Cont.)

1.
The subnet mask goes like this:
If a destination IP address is
206.175.162.21, we know that it is a
Class C address & that its binary
equivalent is:
11001110.10101111.10100010.00010101
Peter Smith
39
A Trial Separation (Cont.)
2.
We also know that the default
standard Class C subnet mask is:
255.255.255.0 and that its binary
equivalent is:
11111111.11111111.11111111.00000000
Peter Smith
40
A Trial Separation (Cont.)
3.
Peter Smith
When these two binary numbers (the IP
address & the subnet mask) are combined
using Boolean Algebra, the Network ID
of the destination network is the result:
41
A Trial Separation (Cont.)
4.
Peter Smith
The result is the IP address of the
network which in this case is the same
as the local network & means that the
message is for a node on the local
network.
42
Routing IP Addresses
When you build a network, you need to
figure out how many network Ids your
network requires.
 To do so, you must account for every
WAN connection & subnet on the
Network.
 Every node & router interface requires
a Host address, or ID.

Peter Smith
43
Routing IP Addresses (Cont.)
There’s no hard & fast rule on how you
should dole out your allotted IP
addresses.
 Commonly, though, the lowest numbers
(1 through 10) are assigned to routers &
servers but how you assign addresses is
strictly up to you & your network
policies & guidelines.

Peter Smith
44
Configuring an IP Address
The proper way to configure an IP
address on the router is through the IP
Address command, which assigns each
router interface its unique IP address.
 A router with 4 interfaces needs 4
separate IP addresses because,
technically each interface (& address) is
on a different network.

Peter Smith
45
Configuring an IP Address
(Cont.)
The IP Address command is entered
from the config-if mode because the
action affects only that interface.
 Both the IP address & the subnet mask
are defined in the command.

Peter Smith
46
Verifying an IP Address
IP addresses are verified using PING,
Trace & Telnet.
 It is important that you know that PING
is used to verify IP address connections
to the Network Layer & that Telnet is
used to verify network IP address
connections to the Application Layer.

Peter Smith
47
Verifying with Telnet
The reason you need to verify IP
addresses is to ensure that the various
parts of a network can properly
communicate with the other parts.
 Eg., if you can Telnet (Terminal
Emulation Protocol) into a router from
a remote location on the same network,
you can verify that the interface & route
are up and available.

Peter Smith
48
Verifying with Telnet (Cont.)

Peter Smith
Because Telnet operates on the OSI
Model’s Application Layer, when it’s
functioning, it’s safe to assume that all
lower layers are also functioning.
49
Verifying with PING
The PING (Packet Internet Groper)
command verifies OSI Layer 3
(Network Layer) connectivity.
 It sends out ICMP (Internet Control
Message Protocol) messages to verify
both the logical addresses & the
Physical connection.

Peter Smith
50
Verifying with PING (Cont.)

Peter Smith
The PING command issued from a Cisco router
responds with a number of single character
responses.
51
Verifying with Traceroute
The Traceroute or Trace command is
used to show the complete route from a
source to a destination.
 Trace sends out probe packets one at a
time to each router or switch in the path
between the source & the destination IP
address entered.

Peter Smith
52
Verifying with Traceroute
(Cont.)
Traceroute displays the round-trip time
for each packet sent to each upstream
router.
 Traceroute has really only 2 results:

Time exceeded or
 Destination unreachable.


Peter Smith
Trace is used to determine where a
breakdown in a route may be occurring.
53
Verifying with Traceroute
(Cont.)

Example on how Trace is used:
A network has 4 routers (A, B, C & D). A
Trace command is issued on router A to
trace the route from itself to router D.
 A timing response comes back from router
B, but the next message indicates that
router C is unreachable. You can be fairly
certain that the problem lies somewhere on
the route between router B & router C.

Peter Smith
54
Verifying with Traceroute
(Cont.)

Peter Smith
Like PING, Trace has its own set of
response codes:
55
Subnetting
Peter Smith
Introduction



Peter Smith
Subnetting is the foundation underlying
the expansion of both Local Networks &
the Internet in today’s world.
Subnetting has become essential
knowledge for the Administrator of any
network.
There are 2 fundamental reasons why
subnetting has so much importance in
today’s networking environment:
57
Introduction (Cont.)
1) The world is running out of available
IP addresses. There just isn’t an
unlimited number of IP addresses
available & subnetting helps extend
the existing addresses until either the
next version of IP is rolled out or
some other technology charges on the
scene.
Peter Smith
58
Introduction (Cont.)
2) Subnetting reduces the size of the
routing tables stored in routers.
Subnetting extends the existing IP
address base & restructures the IP
address. As a result, routers must
have a way to extract from a IP
address both the Network address &
the Host address.
Peter Smith
59
Introduction (Cont.)



Peter Smith
There are only 3 usable IP address classes:
 Class A
 Class B
 Class C
Class A networks have the highest number
of available hosts.
Class C networks have the fewest number
of hosts.
60
Subnetting Networks ID

Peter Smith
A 3-step example of how the default
Class A subnet mask is applied to a
Class A address:
61
Subnetting Networks ID (Cont.)


Peter Smith
In the previous slide, the default Class A
subnet mask (255.0.0.0) is AND’d with the
Class A address (123.123.123.001) using
Boolean Algebra, which results in the
Network ID (123.0.0.0) being revealed.
The default Class B subnet mask
(255.255.0.0) strips out the 16-bit network ID
& the default Class C subnet mask
(255.255.255.0) strips out the 24-bit network
ID.
62
Subnetting, Subnet & Subnet
Mask
Subnetting, a subnet & a subnet mask
are all different.
 In fact, the 1st creates the 2nd & is
identified by the 3rd.
 Subnetting is the process of dividing a
network & its IP addresses into
segments, each of which is called a
subnetwork or subnet.

Peter Smith
63
Subnetting, Subnet & Subnet
Mask (Cont.)

Peter Smith
The subnet mask is the 32-bit number
that the router uses to cover up the
network address to show which bits are
being used to identify the subnet.
64
Subnetting


Peter Smith
A network has its own unique address,
such as a Class B network with the
address 172.20.0.0 which has all zeroes in
the host portion of the address.
From the basic definitions of a Class B
network & the default Class B subnet
mask, you know that this network can be
created as a single network that contains
65,534 individual hosts.
65
Subnetting (Cont.)
Through the use of subnetting, the
network from the previous slide can be
logically divided into subnets with
fewer hosts on each subnetwork.
 It does not improve the available shared
bandwidth only, but it cuts down on the
amount of broadcast traffic generated
over the entire network as well.

Peter Smith
66
Subnetting (Cont.)

The 2 primary benefits of subnetting
are:
1.
2.
Peter Smith
Fewer IP addresses, often as few as one,
are needed to provide addressing to a
network & subnetting.
Subnetting usually results in smaller
routing tables in routers beyond the local
internetwork.
67
Subnetting (Cont.)

Peter Smith
Example of subnetting: when the
network administrator divides the
172.20.0.0 network into 5 smaller
networks – 172.20.1.0, 172.20.2.0,
172.20.3.0, 172.20.4.0 & 172.20.5.0 –
the outside world stills sees the network
as 172.20.0.0, but the internal routers
now break the network addressing into
the 5 smaller subnetworks.
68
Subnetting (Cont.)

Peter Smith
In the example, only a single IP address
is used to reference the network &
instead of 5 network addresses, only
one network reference is included in the
routing tables of routers on other
networks.
69
Borrowing Bits to Grow a
Subnet



Peter Smith
The key concept in subnetting is borrowing
bits from the host portion of the network to
create a subnetwork.
Rules govern this borrowing, ensuring that
some bits are left for a Host ID.
The rules require that two bits remain
available to use for the Host ID& that all of
the subnet bits cannot be all 1s or 0s at the
same time.
70
Borrowing Bits to Grow a
Subnet (Cont.)

Peter Smith
For each IP address class, only a certain
number of bits can be borrowed from
the host portion for use in the subnet
mask.
71
Borrowing Bits to Grow a
Subnet (Cont.)
Bits Available for Creating Subnets
Peter Smith
Address Class
Host Bits
Bits Available for
Subnet
A
24
22
B
16
14
C
8
6
72
Subnetting a Class A Network
The default subnet mask for a class A
network is 255.0.0.0 which allows for
more than 16,000,000 hosts on a single
network.
 The default subnet mask uses only 8
bits to identify the network, leaving 24
bits for host addressing .

Peter Smith
73
Subnetting a Class A Network
(Cont.)


Peter Smith
To subnet a Class A network, you need to
borrow a sufficient number of bits from the
24-bit host portion of the mask to allow for
the number of subnets you plan to create,
now & in the future.
Example: To create 2 subnets with more than
4 millions hosts per subnet, you must borrow
2 bits from the 2nd octet & use 10 masked
(value equals one) bits for the subnet mask
(11111111.11000000) or 255.192 in decimal.
74
Subnetting a Class A Network
(Cont.)
Keep in mind that each of the 8-bit
octets has binary place values.
 When you borrow bits from the Host ID
portion of the standard mask, you don’t
change the value of the bits, only how
they are grouped & used.

Peter Smith
75
Subnetting a Class A Network
(Cont.)
Peter Smith
76
Class A Subnet Masks (Cont.)
A sample of subnet mask options available for Class A addresses.
Peter Smith
77
Class A Subnet Masks (Cont.)
All subnet masks contain 32 bits; no
more, no less.
 However a subnet mask cannot filter
more than 30 bits. This means 2 things:

One, that there cannot be more than 30
ones bits in the subnet mask.
 Two, that there must always be at least 2
bits available for the Host ID.

Peter Smith
78
Class A Subnet Masks (Cont.)
The subnet mask with the highest value
(255.255.255.252) has a binary
representation of:
11111111.11111111.11111111.11111100
 The 2 zeroes in this subnet mask
represent the 2 positions set aside for
the Host address portion of the address.

Peter Smith
79
Class A Subnet Masks (Cont.)

Peter Smith
Remember that the addresses with all
ones (broadcast address) & all zeroes
(local network) cannot be used as they
have special meanings.
80
Subnetting Class B & Class C


Peter Smith
The table on slide 76 “Class A Subnet
Masks” is similar to the tables used for
Class B & Class C IP addresses & subnet
masks.
The only differences are that you have
fewer options (due to a fewer number of
bits available) & that you’re much more
likely to work with Class B & Class C
networks in real life.
81
Subnetting Class B & Class C
(Cont.)
A sample of the subnet masks available for Class B networks.
Peter Smith
82
Subnetting Class B & Class C
(Cont.)
A list of the subnet masks available for Class C networks.
Peter Smith
83
Knowing How to Calculate
Subnets

Peter Smith
To determine the number of subnets & hosts
per subnet available for any of the available
subnet masks, 2 simple formulas to
calculate these numbers:
84
Knowing How to Calculate
Subnets (Cont.)
Although the 2 formulas look identical,
the key is to remember the number
you’re trying to calculate, hosts or
subnets.
 Eg., suppose you are asked to determine
the number of subnets available & the
number of hosts available on each
subnet on the network 192.168.1.0 

Peter Smith
85
Knowing How to Calculate
Subnets (Cont.)

Peter Smith
Using the subnet & hosts formulas, the
answers are easily calculated. Of
course, you must know your powers of
2 to calculate the answers.
86
Class C Subnets

Peter Smith
Knowing the relationships in this table will
significantly reduce the time you spend
calculating subnetting problems.
87
Class C Subnets (Cont.)

Peter Smith
To determine the total length of the
subnet mask, add 24 to the number of
borrowed (subnet) bits.
88
Class B Subnets
To calculate the number of subnets &
hosts available from a Class B subnet
mask, you use the same host & subnet
formulas described for calculating Class
C values.
 Using these formulas I have constructed
a table that contains the Class B subnet
& host values.

Peter Smith
89
Class B Subnets (Cont.)
Peter Smith
90
A Short Broadcast
A broadcast is a message that every
node on a network or subnetwork
receives & examines.
 Cisco IOS supports 2 different types of
broadcast messages:

Flooded
 Directed

Peter Smith
91
A Short Broadcast (Cont.)

Peter Smith
Generally speaking, routers do not
propagate broadcasts, which is one of
the benefits of installing a router in the
first place.
92
A Short Broadcast (Cont.)
Flooded broadcasts (those with the
nominal broadcast address of
255.255.255.255) are not forwarded by
the router & are considered local traffic
only.
 Directed broadcasts, which contain all
1’s in the Host portion of the IP address,
are addressed to a specific subnetwork
Peter Smith & are allowed to pass.
93
