Transcript XS36V4 Series Quick Guide【English】 Front Panel Back

XS36V4 Series Quick Guide【English】
A. Begin Installation
__p
Front Panel
F3
F2
F1.Power Button
F2.Power LED
For safety reasons, please ensure that the power cord is disconnected before
opening the case.
Back Panel
F1
F4
F3.HDD LED
B1. Microphone Jack
B1
B2. Headphone/Line-out Jack
B2
B3. LAN Port
B3
1.Undo one screw of the chassis cover.
B4
2.Slide the cover backwards and upwards.
B5
B4. Kensington Lock
F4.Serial Ports (COM1,COM2)
B5. USB 3.0 Port
F5.SD Card Reader
B6. USB 2.0 Ports
F5
2
B6
B7
B7. HDMI Port
F6.USB 2.0 Port
F7.Vertical Stand
B9. Display Port

Jumper for COM Port Voltage Setting (JP2)
1
1
B10
This mainboard does only support 1.35V DDR3L memory moudles.
1.Locate the SODIMM slot on the mainboard.
2
0V
5V
12V
SODIMM slot
2.Align the notch of the memory module with
the one of the memory slot.
Connecting the System
1
1
B. Memory Module Installation
B10.Power Jack (DC-in)
F7
F6
Screw
B9
B8
B8. D-Sub (VGA) Port
F4
3.Tighten the HDD & bracket with
three screws.
Cutout
Connecting Keyboard/Mouse or USB Devices
Notch
D. Complete
1.Replace the cover and refasten one screw.
2.Tear off the double sided protective membrane.
1
USB Keyboard/Mouse
4
2
3
3.Gently insert the module into the slot in a 45-degree angle.
2
USB Ports
Screw
4.Carefully push down the memory module until it snaps into the locking mechanism.
USB Devices
2
3
1
Connecting LAN
1
1
Wall
5
2
RJ45 Cable
1

Using the Vertical Stand
Install the vertical stand and check that it is properly aligned, then tighten securely with
one screw.
Internet
45-degree
angle
LAN Port
Connecting Monitor or LCD TVs
Digital and analog connections are available so the device can be
connected to computer monitors, flat-panel displays, plasma or LCD TVs.
DSL/Cable Modem
3
4
Connecting Speakers and Microphones
Analog: Connect your computer monitor or LCD TV to the D-Sub Port.
Latch
Latch
Microphone/Headphone
Screw
D-Sub Cable
D-Sub Port
Microphone,
Headphone/Line-out Jack
Display with D-Sub input
Digital: Connect a computer monitor or TV device to the HDMI port.
Speakers
5
Connecting Power
C. HDD Installation
1.Mount the HDD into the bracket with four screws.
3
Vertical Stand
1
2
HDMI Cable
Power Jack (DC-in)
Display with HDMI input
HDMI Port
Digital: Connect a computer monitor or TV device to the Display Port.
6
Powering on the system
2.As shown, install the HDD & bracket in the chassis and push it towards the direction as
indicated by the red arrow to connect the HDD connector.
XS36V4 default BIOS is for use with 64bit operating systems only.
A 32bit BIOS can be downloaded from the Shuttle website, if required.
Safety Information
Read the following precautions before setting up a Shuttle PC.
HDD Connector
CAUTION
Incorrectly replacing the battery may damage this co-mputer.Replace only with the
same or equivalent type recommended by the manufacturer. Disposal of used batteries
according to the manufacturer's instructions.
Display Port Cable
Display Port
Display Port Connector
LThe product’s colour and specifications may vary from the actually shipping product.
53R-XS36V3-2901