Transcript PC Assemble & Disassemble

PC Assemble & Disassemble
Trey, Josh, Jin-young
Step1. Checking PC
Before performing disassemble, make sure
the PC is working properly
Step2. preparing requirement
Please do not use magnetic driver.
It may cause severe damage on
components inside case.
Non-magnetic driver
Anti-static wrist strap or Anti-static mat
: provide protection from electrostatic discharge (ESD)
Step3. Disassembling PC
 Unplug a power cable and other
cables from the back panel, then
put the case on flat surface with
anti-static mat.
 Uncover the case
Hook anti-static clip on proper spot
Before you touch inside
:Uncovered case
Disassembling PC
Unhook all cables inside the case
Power cables, IDE connectors and etc.
Disassembling PC
• Pushing the highlighted spot, pull
the power supply toward outside
Then remove a screw which is
securing the power supply
Disassembling PC
1.Push the secure tab with your driver
Slide ->>>
The edge is enough to cut your finger!
:To avoid minor cut, please do not this with
your hand.
2. then, slide the power supply
toward this side.
Disassembling PC
Removing hard disk drive bay
Disassembling PC
Removing floppy disk drive
1
1
:removing cd/dvd drive
Removing I/O shield
2
1
Disassembling PC
Lift up both side wing
Removing cooling fan
Disassembling PC – motherboard
Unplug LED cable, then remove securing screw from the motherboard
Carefully take out the motherboard
From the case
Backside of motherboard is quite sharp,
so need to pay attention when you handle
This.
Finish!
Twisted side
: it goes to floppy drive
Hard disk drive
Floppy disk drive
Motherboard
CD/DVD drive
Power supply
I/O Shield
RAM
Disassembly complete
At this point the computer has been
fully disassembled.

1.
Everything has been removed from the
case.
Now start to reassemble!
Step 1
Now return the Floppy disk drive
and the CD-ROM to their proper
positions.

1.
1
2.
2
Slide the Floppy disk drive back to its
bay. Then replace the screw.
Next slide the CD-ROM back into its bay
until you hear the click of it being
secured.
Step 2
Replace the hard drive.

1.
2.
1
2
3
3.
Screw the four screws into the cage
securing the hard drive in place.
Now line up the hooks and slide them
into a locking position.
Press it down and replace the screw.
Step 3
Now replace the motherboard.

1.
2.
1
3.
Insert the motherboard.
Align it so that the connectors come out
the back.
Screw it back into place.
Step 4
Plug the power button cable into
the motherboard and install the
RAM.

1.
2.
Place the power button cable on the
matching pins on the motherboard.
Now place each RAM in the shot by
pressing straight down until it clicks.
Step 5
The next component to be replaced
is the fan.

1.
Simply slide the fan back into place and
re-attach the power cable.
Step 6
 Now the I/O shield needs to be
replaced.

1.
2.
Align the sides then slide it in.
Close the lever to secure it in place.
Step 7
Replace the CD-ROM and
Floppy disk drive.

1.
2.
Slide the CD-ROM back into the
drive bay until it pops.
Do the same with the floppy disk
drive then screw it back into place.
Step 8
Now the power supply.

1.
2.
3.
4.
Slide the power supply back into
place
Return the screw.
Reconnect the power cords
Close the power supply cage.
Step 9
Reconnect the Ribbon cables.

1.
2.
The cables have been reconnected.
Then replace the case.
Complete!
The computer has been successfully
reassembled!