Transcript Document

Eighth Edition
5
CHAPTER
VECTOR MECHANICS FOR ENGINEERS:
STATICS
Ferdinand P. Beer
E. Russell Johnston, Jr.
Lecture Notes:
J. Walt Oler
Texas Tech University
Distributed Forces:
Centroids and Centers
of Gravity
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
Eighth
Edition
Vector Mechanics for Engineers: Statics
Contents
Introduction
Theorems of Pappus-Guldinus
Center of Gravity of a 2D Body
Sample Problem 5.7
Centroids and First Moments of Areas
and Lines
Distributed Loads on Beams
Centroids of Common Shapes of Areas
Centroids of Common Shapes of Lines
Center of Gravity of a 3D Body:
Centroid of a Volume
Composite Plates and Areas
Centroids of Common 3D Shapes
Sample Problem 5.1
Composite 3D Bodies
Determination of Centroids by
Integration
Sample Problem 5.12
Sample Problem 5.9
Sample Problem 5.4
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-2
Eighth
Edition
Vector Mechanics for Engineers: Statics
Introduction
• The earth exerts a gravitational force on each of the particles
forming a body. These forces can be replace by a single
equivalent force equal to the weight of the body and applied
at the center of gravity for the body.
• The centroid of an area is analogous to the center of
gravity of a body. The concept of the first moment of an
area is used to locate the centroid.
• Determination of the area of a surface of revolution and
the volume of a body of revolution are accomplished
with the Theorems of Pappus-Guldinus.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-3
Eighth
Edition
Vector Mechanics for Engineers: Statics
Center of Gravity of a 2D Body
• Center of gravity of a plate
• Center of gravity of a wire
 M y x W   xW
  x dW
 M y yW   yW
  y dW
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-4
Eighth
Edition
Vector Mechanics for Engineers: Statics
Centroids and First Moments of Areas and Lines
• Centroid of an area
x W   x dW
x At    x t dA
x A   x dA  Q y
 first moment with respect to y
• Centroid of a line
x W   x dW
x  La    x  a dL
x L   x dL
yL   y dL
yA   y dA  Q x
 first moment with respect to x
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-5
Eighth
Edition
Vector Mechanics for Engineers: Statics
First Moments of Areas and Lines
• An area is symmetric with respect to an axis BB’
if for every point P there exists a point P’ such
that PP’ is perpendicular to BB’ and is divided
into two equal parts by BB’.
• The first moment of an area with respect to a
line of symmetry is zero.
• If an area possesses a line of symmetry, its
centroid lies on that axis
• If an area possesses two lines of symmetry, its
centroid lies at their intersection.
• An area is symmetric with respect to a center O
if for every element dA at (x,y) there exists an
area dA’ of equal area at (-x,-y).
• The centroid of the area coincides with the
center of symmetry.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-6
Eighth
Edition
Vector Mechanics for Engineers: Statics
Centroids of Common Shapes of Areas
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-7
Eighth
Edition
Vector Mechanics for Engineers: Statics
Centroids of Common Shapes of Lines
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-8
Eighth
Edition
Vector Mechanics for Engineers: Statics
Composite Plates and Areas
• Composite plates
X W   x W
Y W   y W
• Composite area
X  A   xA
Y  A   yA
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5-9
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.1
SOLUTION:
• Divide the area into a triangle, rectangle,
and semicircle with a circular cutout.
• Calculate the first moments of each area
with respect to the axes.
For the plane area shown, determine
the first moments with respect to the
x and y axes and the location of the
centroid.
• Find the total area and first moments of
the triangle, rectangle, and semicircle.
Subtract the area and first moment of the
circular cutout.
• Compute the coordinates of the area
centroid by dividing the first moments by
the total area.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 10
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.1
• Find the total area and first moments of the
triangle, rectangle, and semicircle. Subtract the
area and first moment of the circular cutout.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
Qx  506.2  103 mm3
Q y  757.7  103 mm3
5 - 11
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.1
• Compute the coordinates of the area
centroid by dividing the first moments by
the total area.
x A  757.7 103 mm3

X 

 A 13.828103 mm2
X  54.8 mm
y A  506.2 103 mm3

Y 

 A 13.828103 mm2
Y  36.6 mm
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 12
Eighth
Edition
Vector Mechanics for Engineers: Statics
Determination of Centroids by Integration
xA   x dA   xel dA
yA   y dA   yel dA
x A   xel dA
  x  ydx
yA   yel dA
y
   ydx
2
• Define dA as a thin rectangle or strip.
x A   xel dA

ax
 a  x dy
2
yA   yel dA
  y a  x dy
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
x A   xel dA

2r
1

cos  r 2 d 
3
2

yA   yel dA

2r
1

sin   r 2 d 
3
2

5 - 13
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.4
SOLUTION:
• Determine the constant k.
• Evaluate the total area.
• Using either vertical or horizontal
strips, perform a single integration to
find the first moments.
Determine by direct integration the
location of the centroid of a parabolic
spandrel.
• Evaluate the centroid coordinates.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 14
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.4
SOLUTION:
• Determine the constant k.
y  k x2
b  k a2  k 
y
b
a2
x2
or
b
a2
x
a
b1 2
y1 2
• Evaluate the total area.
A   dA
3 a

b
b x
  y dx   2 x 2 dx   2 
 a 3  0
0a
ab

3
a
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 15
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.4
• Using vertical strips, perform a single integration
to find the first moments.
a
 b

Q y   xel dA   xydx   x 2 x 2 dx

0 a
a
 b x4 
a 2b
 2
 
4
 a 4  0
2
a
y
1 b 2
Q x   yel dA   ydx    2 x  dx
2

02a
a
 b 2 x5 
ab 2
 4  
 2a 5  0 10
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 16
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.4
• Or, using horizontal strips, perform a single
integration to find the first moments.
b 2
ax
a  x2
a  x dy  
Q y   xel dA  
dy
2
2
0
1 b  2 a 2
  a 
2 0 
b
2

a
b
y dy 

4

a


Qx   yel dA   y a  x dy   y a  1 2 y1 2 dy


b
a 3 2
ab 2

   ay  1 2 y dy 
10

b
0
b
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 17
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.4
• Evaluate the centroid coordinates.
xA  Q y
ab a 2b
x

3
4
3
x a
4
yA  Q x
ab ab 2
y

3
10
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
y
3
b
10
5 - 18
Eighth
Edition
Vector Mechanics for Engineers: Statics
Theorems of Pappus-Guldinus
• Surface of revolution is generated by rotating a
plane curve about a fixed axis.
• Area of a surface of revolution is
equal to the length of the generating
curve times the distance traveled by
the curve through the rotation.
A  2 yL
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 19
Eighth
Edition
Vector Mechanics for Engineers: Statics
Theorems of Pappus-Guldinus
• Body of revolution is generated by rotating a plane
area about a fixed axis.
• Volume of a body of revolution is
equal to the generating area times
the distance traveled by the area
through the rotation.
V  2 y A
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 20
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.7
SOLUTION:
• Apply the theorem of Pappus-Guldinus
to evaluate the volumes or revolution
for the rectangular rim section and the
inner cutout section.
• Multiply by density and acceleration
to get the mass and acceleration.
The outside diameter of a pulley is 0.8
m, and the cross section of its rim is as
shown. Knowing that the pulley is
made of steel and that the density of
steel is   7.85  103 kg m 3
determine the mass and weight of the
rim.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 21
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.7
SOLUTION:
• Apply the theorem of Pappus-Guldinus
to evaluate the volumes or revolution for
the rectangular rim section and the inner
cutout section.
• Multiply by density and gravitational
acceleration to get the mass and weight.



3
 9 3
m  V  7.85 10 kg m 7.65 10 mm 10 m mm 


W  mg  60.0 kg  9.81 m s 2
3

3
6

© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
3
m  60.0 kg
W  589 N
5 - 22
Eighth
Edition
Vector Mechanics for Engineers: Statics
Distributed Loads on Beams
L
W   wdx   dA  A
0
OP W   xdW
L
OP  A   xdA  x A
0
• A distributed load is represented by plotting the load
per unit length, w (N/m) . The total load is equal to
the area under the load curve. (Note the use of small
w rather than capital W)
• This is the moment of the load about O. A
distributed load can be replace by a concentrated
load with a magnitude equal to the area under the
load curve and a line of action passing through the
area centroid.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 23
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.9
SOLUTION:
• The magnitude of the concentrated load
is equal to the total load or the area under
the curve.
• The line of action of the concentrated
load passes through the centroid of the
area under the curve.
A beam supports a distributed load as
shown. Determine the equivalent
concentrated load and the reactions at
the supports.
• Determine the support reactions by
summing moments about the beam
ends.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 24
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.9
SOLUTION:
• The magnitude of the concentrated load is equal to
the total load or the area under the curve.
Area of trapezium = (1.5+4.5)x6/2 = 18 kN F  18.0 kN
• The line of action of the concentrated load passes
through the centroid of the area under the curve.
Taking moment about A:
(4.5x6/2)x4 + (1.5x6/2)x2 = 63 = 18.X’
63 kN  m
X 
18 kN
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
X  3.5 m
5 - 25
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.9
• Determine the support reactions by summing
moments about the beam ends.
 M A  0 : By 6 m  18 kN3.5 m  0
B y  10.5 kN
 M B  0 :  Ay 6 m  18 kN6 m  3.5 m  0
Ay  7.5 kN
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 26
Eighth
Edition
Vector Mechanics for Engineers: Statics
Center of Gravity of a 3D Body: Centroid of a Volume
• Center of gravity G


 W j    W j 
The moment about an axis through O is:




rG   W j    r   W j 




rGW   j    r W    j 
W   dW


rGW   r dW
• Results are independent of body orientation,
xW   xdW
yW   ydW
zW   zdW
• For homogeneous bodies,
W   V and dW   dV
xV   xdV
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
yV   ydV
zV   zdV
5 - 27
Eighth
Edition
Vector Mechanics for Engineers: Statics
Centroids of Common 3D Shapes
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 28
Eighth
Edition
Vector Mechanics for Engineers: Statics
Composite 3D Bodies
• Moment of the total weight concentrated at the
center of gravity G is equal to the sum of the
moments of the weights of the component parts.
X W   x W
Y W   yW
Z W   z W
• For homogeneous bodies,
X V   x V
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
Y V   yV
Z V   z V
5 - 29
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.12
SOLUTION:
• Form the machine element from a
rectangular parallelepiped and a
quarter cylinder and then subtracting
two 1-in. diameter cylinders.
Locate the center of gravity of the
steel machine element. The diameter
of each hole is 1 in.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 30
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.12
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 31
Eighth
Edition
Vector Mechanics for Engineers: Statics
Sample Problem 5.12

X   x V  V  3.08 in 4
 5.286 in 3 
X  0.577 in.

Y   yV  V   5.047 in 4
 5.286 in 3 
Y  0.577 in.

Z   z V  V  1.618 in 4
 5.286 in 3 
Z  0.577 in.
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.
5 - 32