Transcript No Slide Title

5300 CNC CONTROL
TRAINING GUIDE
Turning the Control ON
After the control has been turned ON press F10
to continue.
F
1
0
1. Control Software
This allows you enter CNC software
2. Setup Utility
Machine configuration
3. Motion Setup/Testing Used to setup drive
Then press ENTER
to select CNC mode.
1.
First CNC Screen
Control Manual Screen
SECTION #1
SECTION #2
SECTION #3
2.
Section #1
Program name
Messages display in this area
Error and warnings
Mold of operation
Machine position status
Machine status
Command line for MANUAL(MDI) instructions
Section #2
Position relative to machine HOME
Target or position to reach
Position relative to part ZERO
3.
Distance to go to reach target
Section #3
Active tool #
Number of loops
to be done
Tool diameter
Tool length offset
Dwell in seconds
Spindle speed
Feedrate
Percentage of
feed and RPM’s
Active fixture offset
Active G codes
Active M functions
Parts counter and time
Override of feed and rapid
4.
Softkey in Manual mold.
Access help
menu
Edit program
in memory
Access list of
programs
Single Step
mold
Delete from
command line
Automatic
mold
Manual mold
Access tool
page
Insert in
command line
Activate
handwheel
Note:When handwheel is active colors will be reversed in box
as shown below.
F10
Softkey in Manual mold when shift key is pressed
Display last 8 messages
Teach Mold
Sends machine home
5.
Exits back main
manual screen
Alfa - Numeric key board
Note :- Most used key are yellow . Most key also double functions , the
shift key is use to use secondary functions.
<
B
>
C
^
E
[
F
]
G
!
I
‘
J
~
K
@
M
{
N
}
O
$
/
‘
A
_
Q
Space key
R
S
D
H
L
P
T
:
U
?
X
&
7
Y
|
4
Z
(
1
V DW
Clear key
%
8
“
9
;
5
/
6
2
#
3
0
*
.
)
=
Shift key
Cursor keys
Enter key
6.
Manual panel
There are two type of Manual panels.
1.As shown below.
2.The other without Handwheel on left side
Manual spindle keys
Manual handwheel
Spindle override
Feedrate override
Servo rest
Y
Z
U
10
W
X
AXIS
100
FEED
1
% FEED
SERVO
RESET
RAPID
% SPDL OVRD
JOG
SPDL
OFF
+
SPDL
REV
SPDL
FWD
C
O
O
L
R
E
A
D
Y
Hold
Start
Direction key for manual
Axis feed type
Axis select for handwheel
Emergence stop
7.
MOVING WITH JOG MOVEMENTS
1) Turn the jog mode selector switch on the MANUAL PANEL to 100, 10, 1, FEED or
RAPID
2) Select the axis to move with the AXIS SELECTOR switch at the MANUAL PANEL
3) Press the
_
or the +
key to move in the desired direction.
MOVING WITH COMMANDS
Type commands as needed and press the START button
MANUAL PANEL
located on the
EXAMPLE:
Type: G0 G90 Z-5. and press Start
Z axis goes to Z-5. in ABS and RAPID
EXAMPLE:
Type G97 S1000 M3 and press START
rpm.
to start the spindle at a fixed 1000
8.
MOST COMMON COMMANDS TO REMEMBER:
Fxxx.x:
Feed Rate in Inch per minute / Inch per rev. (mm/min or mm/revolutions)
G00:
Rapid move.
G01:
Feed move.
G02:
Arc clockwise
G03:
Arc counter clockwise
G17:
XY plane
G18:
XZ plane
G19:
Yz plane
G40:
Cutter comp off
G41:
Cutter comp left
G42:
Cutter comp right
G53 Ox:
Fixture offsets ( absolute shift from Machine Home).
G70:
Inch programming
G71:
MM programming
G80:
Used for Drilling Cycles.
G90:
Absolute co-ordinate system
G91:
Incremental co-ordinate system
G92:
Incremental shift
G94:
Feed Rate in Inch per minute (mm per minute).
G95:
Feed Rate in Inch per revolution (mm per revolution)
M0:
Stop program .
M2:
End of program
M3:
Spindle forward
M4:
Spindle reverse
M5:
Spindle OFF
M8:
Coolant ON
M9:
Coolant OFF
S:
Spindle speed in RPM’s
9.
RETREIVING PROGRAMS FROM DISK
Transferring a program from a disk into the control
Programs can be restored into the control if they have been previously saved on a disk.
Insert the disk into the floppy disk drive (A:) on the machine.
From the MANUAL mode press
Next, press
Log
Using the arrow keys
Utility
then press
Program
then press SHIFT
select “A:” and press ENTER
hi-lite the program to be restored and press
twice to select COPY and then C:
WARNING
Remove the diskette when complete and save in a safe place. Do
not leave the diskette in the machine, the will not start correctly
with disk in the drive.
10.