Goodtool

Brake Service Tools and Supplies

Quick Chuck

Quick Chuck Self centering system

• Will mount on any Brake Lathe with a 1” arbor • Eliminates mounting problems with the unique self centering system • No use of cones or bell clamps • Fits hubless rotors and drums, and composite rotors and drums • Fits most foreign and domestic rotors, drums and flywheels including light trucks with a centering hole ranging from 2-1/8” to 5 -3/4” in diameter • 25% less set up time, accurate microfinish and reduces chatter.

• Fits on small automotive to large truck rotors Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

2

Go From all this… To just this…

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

3

Step One

• Thoroughly clean the surface of the rotor or drum that will be mounted on the Quick Chuck. ( Step 1A & 1B) Step 1B Step 1A Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

4

Step 2

• Place the hubless rotor or hubless drum on a clean, flat surface. Attach your hubless rotor or drum to the Quick Chuck by positioning the Quick Chuck with the jaws in the center hole. Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

5

Step 2B

• Tighten the jaws by inserting the key into one of the key slots in the side of the chuck, turning counterclockwise. The Quick Chuck will automatically self-center the rotor or drum. Make sure that the chuck jaws are tight.

DO NOT

leave the key in the key slot when starting the brake lathe.

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

6

Step 3A

• Install the backing plate onto the brake lathe arbor with offset backing outward. Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

7

Step 3B

• Mount the Quick Chuck with drum or rotor installed onto the 1" arbor Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

8

Step 3C

• Using the spacers supplied with the brake lathe, add as many as needed to reach the arbor threads Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

9

Step 3D

• Using the adjusting nut supplied with the machine, tighten the nut against the spacers. After tightening the Quick Chuck, turn on the brake lathe to check for run-out of the rotor or drum. Run-out spec. is .001” You are now ready to resurface the rotor or drum.

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

10

• This job can be done quickly and will eliminate customer’s complaints of rotors or drums saving you time and making you money.

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

11

• SPECIAL NOTE: The Quick Chuck will allow the turning of hubless rotors and drums to be performed on any brake lathe with an 1” arbor.

Ammco Twin Cutters Horvath Hunter Kwik-Way Accu-Turn Performance Bear Ammco HD Van Norman Bean Hoffman FMC Rels Pro-Cut RTI RJ West Star VBG Snap-On

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

12

• Important – Please note ALWAYS use the largest possible backing plate. This will help eliminate the rotor or drum vibration while being turned. On some brake lathes, a small spacer may be needed before the installation of the backing plate.

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

13

•

*Do not use air tools on the unit at any time.

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

14

• NOTE: THE CLEANING OF THE CHUCK. When the jaws have been removed it allows for cleaning of the Chuck (the jaws are numbered on the side as 1, 2, 3) it is VERY IMPORTANT that they be reinstalled in the same manner that they were removed. Reinstall in the order of 1-2-3 (counterclockwise). A slight amount of pressure may be required on each of the jaws to allow them to be reinstalled evenly and correctly. (Figure 1 & 2 below)

1 294

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

15

Automotive Quick Chuck Parts

GT-70040 -- Automotive Chuck Adaptor Kit Kit includes • Quick Chuck Adaptor • Automotive Jaws Range of 2-1/8” to 3-3/4” • Standard Backing Plate 5.2” OD • Chuck Key Fits 1” Arbors Replacement parts GT-70042 -- Quick Chuck Adaptor w/ Jaws GT-70045 -- Replacement Automotive Jaws 2-1/8” to 3-3/4” GT-70043 -- Standard Backing Plate 5.2” OD GT-70044 -- Chuck Key Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

16

Truck Quick Chuck Parts

GT-70040 -- Truck Chuck Adaptor Kit (can be used for automotive applications) • • • • • • Kit includes Quick Chuck Adaptor Automotive Jaws Range of 2-1/8” to 3- 3/4” Truck Jaws Range of 3-3/4” to 5-3/4” Truck Backing Plate 7-1/4” OD Standard Backing Plate 5.2” OD Chuck Key Fits 1”Arbors Replacement parts GT-70042 -- Quick Chuck Adaptor w/ Jaws GT-70045 -- Replacement Automotive Jaws range of 2-1/8”to 3-3/4” GT-70041 -- Large Jaw Set range of 3-3/4 “ to 5-3/4” GT-70046 -- Truck Backing Plate 7-1/4 “ OD GT-70043 -- Standard Backing Plate 5.2” OD GT-70044 -- Chuck Key Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

17

Other Optional Parts

GT-70047 -- Small Automotive Backing Plate Plate 4-1/4” OD GT-70054 -- Toyota Backing Plate 6-1/4” OD (Each sold separately not included in any kits) Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

18

Goodtool

Brake Service Tools and Supplies • Quick Chuck

• Any questions on the Quick Chuck : please contact us • Toll Free: 1-800-880-7121 • Phone: 507-454-1454 • Fax: 507-454-1471 • www.goodtool-online.com.com

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com

19