R.H.

L.H.

Exploded view

30-4-2020 2

Sectional views

30-4-2020 3

Parts breakdown

Lux 40/40 series top and bottom rails Code :

P1406610

Cut dimension = frame width 80 Lux 40/40 series (LH/RH) stile Code : T

1407220/T14072-22

Cut dimension = frame height - 6 Stile cover (40 x 17) Code :

P1407310

Cut dimension = frame height - 6 30-4-2020 60F series blade (60 x 10) Code :

P11634-10

Cut dimension = frame width - 80 Lux 40/40 series cover plate Code :

G0100522

Thread-forming screw : DIN 7500 Form C, M6 x 30, A2 stainless steel Pan head with PZ 3 drive Code :

G0100525

(Needed for fixing the frame) 4

Parts breakdown

Pozi pan self tapping screw A2 stainless steel, Ø 3.5 x 19, to DIN 7981/C Pan head with PZ drive Code :

G0000102

(Needed for fixing the blades) Thread-forming screw : DIN 7500 Form M, M4 x 20, A2 stainless steel Countersunk head with PZ 2 drive Code :

G0100526

(Needed for fixing the cover plates.) Top rail suspension bracket 30/47/3 & 30/60/3 Code :

G0013031

30-4-2020 Self-drilling screw : A2 stainless steel, M4.8 x 16, DIN 7504 Form M Pan head with PH 2 drive Code :

G0000227

(Needed for fixing the suspension bracket) Bottom guide foot Code :

G0100700

Self-drilling screw : DIN 7504 Form O, M3.9 x 19, A2 stainless steel Countersunk head with PH 2 drive Code :

G0100528

(Needed for fixing the bottom guide foot.) 5

Parts breakdown

Lux40 60F series cover plate Code :

G0100642

(Needed for covering the threaded hole) 4 x 10 mm blind rivet Aluminium AL-AL Code :

G0000064

(Needed for fixing the cover caps) Cutting jig for Lux 40 series rails for

T1407220 (L.H.)

Code

: K0001734

30-4-2020 Cutting jig for Lux 40 series rails for

T1407222 (R.H.)

Code

: K0001733

Drilling jig for Lux 40 series rails for

P14072

Code

: K0001732

Top rail suspension bracket 31/33/2 Code:

G0013080

6

Cutting list

• All cut lengths of the individual sections/rails are specified in the parts list.

• The dimensions labelled “center onderste gat tot zaagsnede” (for "center-to-center distance from bottom hole to cutting line") & “zaagmaat kaliber / maat totaal” (for "cut dimension jig / total length") and required for cutting the drilled rails are specified ; please make sure to send these dimensions to our production department.

Calculations tab sheet The cut dimension "cutting jig" applies only to sections cut to length with Duco's proprietary cutting jig.

30-4-2020 7

Cutting to length

30-4-2020 Cut all sections to size.

1. Both the top and the bottom rail

P1406610

at frame width -80mm.

2. 60F series blade

P1163410

at frame width -80mm.

3. Stile cover trim

P14073-10

at frame height 6mm.

8

Cutting the stiles to size

L.H.

R.H.

30-4-2020 Bottom L.H.

R.H.

• When cutting the stiles, make sure to always place the cutting jig at the bottom of the section.

• To check whether the section is long enough at the bottom, the Lux 40 series section should be visible through the Ø 10 hole prepared in the jig. (Alternately, instead of looking through the hole, it should not be possible to poke a Ø 10 pin or a M10 bolt through the frame profile.) 1.Cut the section to “maat zaagmal” (for "length by cutting jig") using the cutting jig.

2.Remove the cutting jig and put the cut profile with its cutting line flat against the cutting jig.

3.Cut the section at “maat totaal” (for "total length") WITHOUT using the cutting jig.

Remark: In case no cutting jig is available, us the measure “afstand center onderste gat tot zaagsnede” (for "center-to-center distance from bottom hole to cutting line") instead.

9

Fitting sequence

30-4-2020 Using the drilling jig K0001732, drill ø 6.5 mm holes at the top and bottom of the stiles T14072-20/22, to permanently secure the top and bottom rail. Make sure the drilling jig is a tight fit against the extreme end of the vertical profiles and hold it in position using a quick action clamp or an F-clamp.

10

Fitting sequence

Fix the stiles T14072-20/22 to both the top and bottom rail P1406610 using 8 M6 x 30 screws (G0100525). 30-4-2020 11

Fitting sequence

Fix the blades P11634-10 to the stiles T14072-20/22 with four M3.5 x 19 screws G0000102 for each blade.

Remark: Please take note of the correct positioning !

30-4-2020 12

Fitting sequence

Fit the four cover caps G0100522 on the ends of stiles.

30-4-2020 13

*Place the suspension bracket G0013031 or G0013080 on the top rail of the slide using the positioning jig. Be sure the hole provided in the suspension bracket, to accommodate the suspension bracket screw, points towards the rear of the slide. Fasten it with four A2 stainless steel M 4.8 x 19 self-drilling screws with PH 2 drive, to DIN 7504-M (G0000227). Do this for both sides of the slide.

A choice of three possible fixing positions of the suspension bracket (G0013031 or G0013080) is available : These positions vary depending upon what the customer ordered !

1) Standard position at 150 mm, for manually operated slides ; 2) underneath the actuator at 200 mm, for motorized single slides ; 3) With motorized symmetrical slides : underneath the actuator at 200 mm ; in the center at 2 x 100 mm ; at the return pulley at 150 mm ; 4) With motorized triple slides : underneath the actuator at 200 mm ; at the opposite side of the motorized actuator at 170 mm ; the other two slides at 150 mm. These different positions can be set by shifting of removing the pin, depending on the position by the suspension bracket. 30-4-2020 14

Place the bottom guide base (G0100700

)

on the bottom rail of the slide using the positioning jig. Fasten it with an A2 stainless steel M 3.9 x 19 self drilling screw with PH 2 drive, to DIN 7504-O (G0100528). Do this for both sides of the slide.

30-4-2020 15

CE label Put the CE-label on a visible spot, for example on the side of the frame (do not put it on the blades) Make sure the label fits good on the frame.

16