Transcript Document

Installation on Windows Vista/Windows 7
NOTE: Installation on Windows Vista can differ depending
on the version of Windows installed​
In most computers it is installed as demonstrated in this
instruction manual
Note: Installation not designed for MAC computers
Step 1: Type the following
link into the search engine
to begin download:
www.clap.opsoms.org/system.html
Once the page is opened:
1. Download the guideline by clicking
SIP_BahamasGuide
2. Click the link “SIP_Bahamas” shown in the
image to the right.
Once it has completely downloaded, open the
“SETUP_Bahamas.exe” extension by clicking it
and proceed to the next step
Step 2: Allow the program
permission to run on the
computer system
The program must be granted
permission to run on the computer.
Click “Run” to grant permission
Step 3: Allow time for
complete download of the
software
The following screen will appear once
the download begins. The green bar
indicates how far the installation is to
completion.
At no point in the downloading
process should you close this box or
click “cancelar” which cancels the
download
Step 4: Set up your user
account
Once your download is completed, you
will be shown this screen. Click “>>"
which means "next".
NOTE: CRUCIAL STEP! Must be performed correctly or will create errors
in running the program
Step 5: Change the file
location
A folder will appear with the title
“C.\Program File\sip\", however this
folder location must be changed.
To change the folder location click the
"cambiar-change" button at the top
right.
Step 6: Enter the new file
location
After selecting the change file location
in step 5, now enter the new file
location by typing in the last box
“C:\sip\” then click “OK”
Step 7: Install the program​
Next, click the “>>" button to begin
installation. A green bar indicates it is
successfully installing
Step 8: Confirm the
installation
Once the bar completely loads
(complete green) it will automatically
move to step 9
Step 9: Finalize the
Installation
To complete the installation you must
finalize it by clicking “Exit"
After it is completely finalized a SIP
icon will appear on the desktop.
Step 10: Program
Start Up
To open the program click the SIP icon
(located on the desktop) twice.
Step 11: File uploading
The following messages may appear in
Spanish in a dialog box and
corresponds to files needing to be
installed. Click “OK” to both
Note: If these message does not
appear, you are completed at this step
and the program will immediately
open. Otherwise, complete the last
two steps
Step 12: Enter SIP
To enter into the program only press
the " enter" button on your keyboard
once
Once completed the program will
automatically launch into the SIPBahamas program.
Step 13: Configuration of
SIP
The following message will appear
asking if you want the system to
configure to its original version. Click
“OK” for the configuration to occur
Note: This message may not appear
on your screen. If not, proceed to step
14
Step 14: Selection of
Language Preference
To translate the program to English,
select the “English” icon to the bottom
of the page as demonstrated in the
image top right.
A message will appear asking you to
confirm your language preference by
selecting “Yes”.
Step 15: Specify your
program Setup
To specify your program setup you
must select the “Management
programs” tab followed by selecting
the “General Setup Specifications”
option
Step 16: Country Selection
In the “Country” tab select the
“Bahamas” as your country then click
the save icon as demonstrated in the
image.
A message will appear saying that the
selection was successfully made. Click
“OK” and then exit this box by clicking
the “x” in the top right hand corner
Step 17: How to Enter a
Clinical Record
Once you have successfully completed
the previous steps you are now ready
to enter information into the online
system
To begin entering patient information
select the “Enter a Clinical Record” tab
as illustrated in the image to the right.
This selection will launch the virtual
perinatal record as displayed in step 18
Step 18: Enter Information
in the Perinatal Record
To enter information on the virtual
card, select the area you wish to enter
information and double click into the
spot. A blinking cursor indicates that
you can enter information .
To reverse sides of the card select the
“R” at the top of the page as shown in
the image to the right. Once on the
reverse side, to go back to the first side
of the card click “A” which is also found
at the top right.
Remember to save information as you
go along by selecting the save button
found to the top.