Transcript Slide 1
Civil & Environmental Engineering Non-Destructive Testing of Wood-Based Composites Using Ultrasonic Stress Waves Jean Carlo Vilalta, Undergraduate Research Assistant & Thomas Schumacher, Assistant Professor (Adviser) Table 1. Estimated p-wave velocities for all specimens Introduction and Background Experimental Methodology • The test setup is illustrated in Figure 3. This setup is often referred to as ‘pitch-catch’ where a piezoelectric transmitter creates a ultrasonic stress wave on one side of the specimen that is measured on the opposite face by a piezoelectric receiver. The fastest stress wave type that exists in a solid is the so-called compression or p-(primary) wave mode. For this study, a wave signal as shown in Figure 4 (black line) with a peak frequency of 150 kHz was used as input signal and repeated several times so that statistical variations of the measurement and material could be established. • • • Wood and wood-based composites are more likely than other materials to decay under certain environmental conditions and exposure. Non-destructive testing (NDT) is commonly used to determine the properties of different materials such as metals, polymers, and concrete, without varying their end-use capabilities. NDT may be used to analyze physical and mechanical properties of wood-based composites. Specifically, ultrasonic NDT may be useful in the evaluation of wood-based composites during the manufacturing process to estimate glue line quality and to detect flaws (see Figure 1) to accomplish quality control. Waveform Generator Data Acquisition System Signal Preamplifier Waveform Amplifier Receiver Transmitter Figure 1. Example of a ‘blow-out’ (large crack parallel to the surface of the specimen) in a wood-based composite. Computer using wave recording software The objective of this study is to evaluate ultrasonic NDT methods for the detection and visualization of flaws in wood-based such as ‘blow-outs’ Objectives:composites To detect (using ultrasonic NDT) any flawsand or the distribution andwithin quality the specimens glue line. otherwise irregularities theof wood undetectable by visual means. Specimen (a) Figure 3. Experimental setup Test Specimens Results Four engineered-wood-type specimens were tested and are shown in Figure 2: 1) 0.75” thick, 16” x 3”, plywood (Figure 2.a) 2) 0.75” thick, 16” x 3”, oriented strand board (OSB) (Figure 2.b) 3) 0.75” thick, 16” x 16”, low-density particle board with a ‘blow-out’ (Figure 2.c) 4) 0.75” thick, 16” x 16”, low-density particle board (Figure 2.d) Two parameters were determined from the recorded data using Matlab: • The p-wave amplitudes Ap of the received signals (see Figure 4.a) • The p-wave velocity cp using the time difference Dt and thickness d between the transmitted and the received signal (see Figure 4.a) (c) Figure 2. Test specimens (d) Figure 5. Contour plots for p-wave velocities in (a) low density panel and (b) panel with a blow-out board Conclusions The different specimens could be distinguished by the different pwave velocities. Using ultrasonic NDT, flaws in wood-based composites such as ‘blow-outs’ can be quantified and localized. Dt Future Work Ap (a) (b) Figure 4. Example of transmitted (black) and received (red) signal waveforms from (a) an integer area and (b) an area having a ‘blow-out’. (b) (b) Change in time (s) of wave arrival d cp Dt (a) Figure 5 shows an example of how the data can be represented using a contour plot for the p-wave velocities for specimens 3) and 4): It was found that the p-wave amplitudes from the OSB (Figure 2.b) had a lower amplitude and a slower velocity than the plywood (Figure 2.a). This can be attributed to a lower density (more voids) of the OSB. Continued evaluation of wood-based composites using ultrasonic stress wave propagation and correlation with mechanical properties such as density, glue line content and quality, and tensile and shear strength. Acknowledgments This research work was sponsored by the University of Delaware Research Foundation (UDRF) Research Experience for Undergraduates (REU) Summer Internship Program. Wood composite specimens were provided by Arijit Sinha, Assistant Professor in Wood Science at Oregon State University. The support is greatly appreciated.