Transcript Slide 1

Welcome
to
Unrestricted Construction Supervisor Exam Content Outline
Subject Area
Approx. Percent
Approx. Test Questions
Approx. % IRC
Approx. IRC
Questions
Approx. % IBC
Approx. IBC
Questions
Approx. IECC
Questions
Unrestricted Construction Supervisor
Administrative Responsibilities
8%
6
5%
4
3%
2
General Building Construction Knowledge
11%
8
7%
5
4%
3
Energy Efficiency
6%
5
0%
0
0%
0
Accessibility
4%
3
3%
2
1%
1
Sitework & Foundations
7%
5
5%
3
2%
2
Concrete and Masonry
9%
7
6%
4
3%
2
Moisture Intrusion/Protection
7%
5
5%
3
2%
2
Structural Framing (Steel and Wood)
13%
10
8%
6
5%
3
Roofing/Exterior Walls
7%
5
5%
3
2%
2
Doors/Windows
5%
4
3%
2
2%
1
Interior Environment (Mechanical and Ventilation)
7%
5
5%
3
2%
2
Fire Protection (Mechanical)
5%
4
3%
2
2%
1
Safety (Construction Safety and Lead Remediation)
11%
8
7%
5
4%
3
5
6
Unrestricted Construction Supervisor Exam
Content Outline
Based on 200 Sample Questions
Unrestricted Construction Supervisor Exam Content Outline
Based on 200 Sample Questions
Based on 200 Sample Questions
Approx. Percent
Approx. Test Questions
Approx. % IRC
Approx. IRC
Questions
Approx. % IBC
Approx. IBC
Questions
Unrestricted Construction Supervisor
Administrative Responsibilities
8%
16
5%
10
3%
6
General Building Construction Knowledge
11%
22
7%
14
4%
8
Energy Efficiency
6%
12
0%
0
0%
0
Accessibility
4%
8
3%
5
1%
3
Sitework & Foundations
7%
14
5%
9
2%
5
Concrete and Masonry
9%
18
6%
12
3%
6
Moisture Intrusion/Protection
7%
14
5%
9
2%
5
Structural Framing (Steel and Wood)
13%
26
8%
17
5%
9
Roofing/Exterior Walls
7%
14
5%
9
2%
5
Doors/Windows
5%
10
3%
7
2%
4
Interior Environment (Mechanical and
Ventilation)
7%
14
5%
9
2%
5
Fire Protection (Mechanical)
5%
10
3%
7
2%
4
Safety (Construction Safety and Lead
Remediation)
11%
22
7%
14
4%
8
Approx. IECC
Questions
12
6
Sample Questions
What is the minimum compressive strength in psi for a concrete
basement slab with negligible weathering potential?
A. 1500
B. 2000
C. 2500
D. 4000
What is the minimum compressive strength in psi for a concrete
basement slab with negligible weathering potential?
A. 1500
B. 2000
C. 2500
D. 4000
To find this answer we first look for keywords in the question.
Basement slab tells us we are dealing with a residential application and using
the IRC Basement slab also implies foundation so we go to the Foundations
Chapter 4 From the question, concrete is the material. Materials for
Foundations is Section R402.2 In Section R402.2, the description for concrete
points us to Table R402.2. In Table R402.2, we see that for a basement slab
with negligible weathering potential, the minimum compressive strength is
2,500 psi. The answer is located on Page 42 of the IRC.
2. An accessory structure is a structure not greater than ___ square feet
A 1,000
B 2,000
C 3,000
D 4,000
2. An accessory structure is a structure not greater than ___ square feet
A 1,000
B 2,000
C 3,000
D 4,000
Keywords - Accessory Structure
A good pace to start for all questions is the index If you look in the index under
Accessory Structure, it points to Section R202 In Section R202, we find the
definition of an Accessory Structure to be a structure not greater than 3,000
square feet. The answer is located on Page 9 of the IRC.
3. What is the R Value insulation requirement for a residential floor in climate zone 3
A 13
B 19
C 30
D 38
3. What is the R Value insulation requirement for a residential floor in climate zone 3
A 13
B 19
C 30
D 38
Keywords - Insulation Requirement
Climate Zone tells us we should look in the IECC Again, we first go to the index
under Insulation Under insulation, there is a section for Requirements 402.1.1 In
Section 402.1.1, we see Table 402.1.1 and look under the Floor Column in Climate
Zone 3 and see that the R Value is 19. The answer is located on Page 27 of the
IECC.
4. For a Means of Egress Door, what is the minimum
width of each door opening in inches?
A 24
B 28
C 32
D 36
4. For a Means of Egress Door, what is the minimum
width of each door opening in inches?
A 24
B 28
C 32
D 36
Keywords - Means of Egress Means of Egress tells us this is more of a
Global Requirement and we would first look at the IBC In the Index, under
Means of Egress, there is a Section for Doors Under the Door Section it
points us to Section 1005.2 and then 1008 In Section 1005.2, we do not
get our answer so we go to 1008 In Section 1008 under 1008.1.1 Size of
Doors, we see that the minimum width for a Means of Egress Dorr is 32
inches. The answer is located on Page 224 of the IBC.
5. Exterior wood framing walls shall be a minimum of ___ grade wood.
A Utility
B2
C3
D4
5. Exterior wood framing walls shall be a minimum of ___ grade wood.
A Utility
B2
C3
D4
Keywords - Wood Walls
There are not many commercial buildings with wood walls, so we'll first
look in the IRC In the Index under Wood there is a Section called Walls
which points us to R602 In Section R602.2 Grade, we see that Studs shall
be a minimum of Grade 3. The answer is located on Page 146 of the IRC.
Administrative
Responsibilities
1. Which of the following is not considered work
exempt from a permit?
A Swings & Playground Equipment
B Sidewalks
C Fences less than 6 feet
D Interior Painting
1. Which of the following is not considered work
exempt from a permit?
A Swings & Playground Equipment
B Sidewalks
C Fences less than 6 feet
D Interior Painting
Keywords - Permit Exempt From the index,
Section R105 is Permits Section R105.2 is
Work Exempt From the list you see the answer is C.
The answer is located on Page 3 of the IRC.
2. A permit becomes invalid if the work authorized by the permit does not begin
in ___ days.
A 90
B 120
C 180
D 365
2. A permit becomes invalid if the work authorized by the permit does not begin
in ___ days.
A 90
B 120
C 180
D 365
Keywords - Permit, Days From the index, Section R105 is Permits Section R105.5
is Expiration From the definition you see the answer is C. The answer is located on
Page 4 of the IRC.
3. The building permit shall be kept on site until the work is complete.
A TRUE
B FALSE
3. The building permit shall be kept on site until the work is complete.
A TRUE
B FALSE
Keywords - Permit From the index, Section R105 is Permits Section R105.7 is
Placement From the definition you see the statement is True. The answer is located
on Page 4 of the IRC.
4. When shall a final inspection be conducted?
A.
B.
C.
D.
After the permit is issued
After permitted work is complete
After the occupants move in
Upon beginning the permitted work
4. When shall a final inspection be conducted?
A.
B.
C.
D.
After the permit is issued
After permitted work is complete
After the occupants move in
Upon beginning the permitted work
Keywords - Final Inspection From the index, Section R109 is Inspections Section
R109.1.6 is Final Inspection From the definition you see the answer is B. The
answer is located on Page 6 of the IRC.
5. Which of the following is required in a Certificate of Occupancy?
A. Name & Address of Owner
B. Name of Building Official
C. Edition of the Code permit
was issued under
D. All of the Above
5. Which of the following is required in a Certificate of Occupancy?
A. Name & Address of Owner
B. Name of Building Official
C. Edition of the Code permit
was issued under
D. All of the Above
Keywords - Certificate of Occupancy From the index, Section R110 is
Certificate of Occupancy Section R110.3 is Certificate Issued From the list
you see the answer is D. The answer is located on Page 7 of the IRC.
6. Which of the following is not required on a site plan?
A.
B.
C.
D.
Location of new construction
Distance from lot lines
Traffic Control Plan
Location of existing structures
6. Which of the following is not required on a site plan?
A.
B.
C.
D.
Location of new construction
Distance from lot lines
Traffic Control Plan
Location of existing structures
Keywords - Site Plan (which is a construction document) From the index,
Section R106 is Construction Documents Section R106.2 is Site Plan From the
Definition you see the answer is C. The answer is located on Page 5 of the IRC.
7. How long must you retain approved construction documents after the work
is completed?
A.
B.
C.
D.
30 Days
60 Days
90 Days
180 Days
7. How long must you retain approved construction documents after the work
is completed?
A.
B.
C.
D.
30 Days
60 Days
90 Days
180 Days
Keywords - Retain, Construction Documents From the index, Section R106 is
Construction Documents Section R106.5 is Retention of Construction Documents
From the Definition you see the answer is D. The answer is located on Page 5 of the
IRC.
8. Who is authorized to establish a refund policy for permit fees?
A.
B.
C.
D.
Building Official
Owner
Accountant
Designer
8. Who is authorized to establish a refund policy for permit fees?
A.
B.
C.
D.
Building Official
Owner
Accountant
Designer
Keywords - Refund, Permit From the index, Section R108 is Fees Section
R108.5 is Refunds From the Definition you see the answer is A. The answer is
located on Page 6 of the IRC.
9. You are allowed to continue work safely after a stop work order has been
issued.
A. TRUE
B. FALSE
9. You are allowed to continue work safely after a stop work order has been
issued.
A. TRUE
B. FALSE
Keywords - Stop Work Order, Continue From the index, Section R114 is Stop
Work Order Section R114.2 is Unlawful Continuance From the Definition you see
the answer is B. The answer is located on Page 8 of the IRC.
10. Who appoints the building official from the Department of Building Safety?
A. Owner of building
B. Engineer on record
C. Chief Appointing Authority of the
Jurisdiction
D. Mayor's Assistant of the
Jurisdiction issuing permit
10. Who appoints the building official from the Department of Building Safety?
A. Owner of building
B. Engineer on record
C. Chief Appointing Authority of the
Jurisdiction
D. Mayor's Assistant of the
Jurisdiction issuing permit
Keywords - Building Safety, Building Official, Appoints From the index, Section
R103 is Dept of Building Safety Section R103.2 is Appointment From the
Definition you see the answer is C. The answer is located on Page 1 of the
IRC.
IBC
11. When there is a conflict and different sections of the IBC specify different
materials…..
A. Use the less restrictive guidance
B. Use the most restrictive guidance
C. Use whichever material is readily
available
D. Use the more expensive option
IBC
11. When there is a conflict and different sections of the IBC specify different
materials…..
A. Use the less restrictive guidance
B. Use the most restrictive guidance
C. Use whichever material is readily
available
D. Use the more expensive option
This is a Global Administrative Question. Think IBC. From the index, Chapter
1 is Scope & Administration Section 102.1 is General Applicability From this
Section you see the answer is B. The answer is located on Page 1 of the IBC.
IBC
12. Live loads for floors and roofs must be posted by the owner when they
exceed ___ PSF
A.
B.
C.
D.
25
30
50
100
IBC
12. Live loads for floors and roofs must be posted by the owner when they
exceed ___ PSF
A.
B.
C.
D.
25
30
50
100
Keywords - Floors and Roofs, Posted This is a Global Administrative Question.
Think IBC. From the index, Chapter 1 is Scope & Administration Section 106.1 is
Floor and Roof Design Loads From this Section you see the answer is C. The
answer is located on Page 5 of the IBC.
IBC
13. A permit is not valid until…
A.
B.
C.
D.
It is approved
The fee has been paid
It is posted at the site
The site plan has been posted
IBC
13. A permit is not valid until…
A.
B.
C.
D.
It is approved
The fee has been paid
It is posted at the site
The site plan has been posted
Keywords - Permit This is a Global Administrative Question. Think IBC. From
the index, Chapter 1 is Scope & Administration Section 109 is Fees From this
Section you see the answer is B. The answer is located on Page 6 of the IBC.
IBC
14. Who has the authority to authorize temporary utility connections?
A.
B.
C.
D.
Building Official
Owner
Engineer
Designer
IBC
14. Who has the authority to authorize temporary utility connections?
A.
B.
C.
D.
Building Official
Owner
Engineer
Designer
Keywords - Permit This is a Global Administrative Question. Think IBC. From
the index, Chapter 1 is Scope & Administration Section 112 is Service Utilities
From this Section you see the answer is A. The answer is located on Page 8 of
the IBC.
IBC
15. A detached 400 square foot storage shed does not require a permit.
A. TRUE
B. FALSE
IBC
15. A detached 400 square foot storage shed does not require a permit.
A. TRUE
B. FALSE
Keywords - Permit This is a Global Administrative Question. Think IBC. From the
index, Chapter 1 is Scope & Administration Section 105 is Permits and 105.2 is
Permits work exempt from Permits From this Section you see the answer is B.
The answer is located on Page 4 of the IBC.
IBC
16. Footing and foundation inspections should occur…
A. Prior to construction
B. During the design phase
C. After excavation is complete and
rebar is installed
D. After excavation is complete but
prior to rebar installation
IBC
16. Footing and foundation inspections should occur…
A. Prior to construction
B. During the design phase
C. After excavation is complete and
rebar is installed
D. After excavation is complete but
prior to rebar installation
Keywords - Foundation Inspections This is a Global Administrative Question.
Think IBC. From the index, Chapter 1 is Scope & Administration Section 110 is
Inspections and 110.3.1 is Footing and Foundation Inspections From this Section
you see the answer is C. The answer is located on Page 7 of the IBC.
General
Knowledge
IRC
1. What is the maximum slope of a ramp?
A.
B.
C.
D.
4 to 1
8 to 1
10 to 1
12 to 1
IRC
1. What is the maximum slope of a ramp?
A.
B.
C.
D.
4 to 1
8 to 1
10 to 1
12 to 1
Keywords - Maximum Slope, Ramp From the index, Chapter 3 is Building
Planning Section R311 is Means of Egress Section R311.8 is Ramps, and from
Section R311.8.1 you see the answer is D. The answer is located on Page 61
of the IRC.
IRC
2. A drill hole for piping or conduit shall be a minimum of __ inches from the
top and bottom of the floor joist.
A.
B.
C.
D.
1
2
3
4
IRC
2. A drill hole for piping or conduit shall be a minimum of __ inches from the
top and bottom of the floor joist.
A.
B.
C.
D.
1
2
3
4
Keywords - Drill hole for conduit, floor joist From the index, Chapter 5 is
Floors Section R502 is Wood Floor Framing From Section R502.8 you see
the answer is A. The answer is located on Page 114 of the IRC.
IRC
3. After the 1st coat is applied, when should the 2nd coat of cement plaster be
applied .
A.
B.
C.
D.
12 hrs
24 hrs
36 hrs
48 hrs
IRC
3. After the 1st coat is applied, when should the 2nd coat of cement plaster be
applied .
A.
B.
C.
D.
12 hrs
24 hrs
36 hrs
48 hrs
Keywords - Cement Plaster, 2nd Coat From the index, Chapter 7 is Wall Covering
Section R702 is Interior Covering Section R702.2 is Interior Plaster, and from Section
R702.2.2 you see the answer is D. The answer is located on Page 359 of the IRC.
IRC
4. Exhaust ducts associated with clothes dryers shall terminate outside of the
building.
A. TRUE
B. FALSE
IRC
4. Exhaust ducts associated with clothes dryers shall terminate outside of the
building.
A. TRUE
B. FALSE
Keywords - Exhaust Ducts, Dryers From the index, Chapter 15 is Exhaust Systems
Section M1502 is Clothes Dryer Exhaust From Section M1502.3 you see the
answer is A. The answer is located on Page 487 of the IRC.
IRC
5. Electrical equipment intended to interrupt current at fault levels shall have a
minimum interrupting rating of ___ amperes.
A.
B.
C.
D.
1
5,000
10,000
15,000
IRC
5. Electrical equipment intended to interrupt current at fault levels shall have a
minimum interrupting rating of ___ amperes.
A.
B.
C.
D.
1
5,000
10,000
15,000
Keywords - Electrical Equipment, Interrupting Rating From the index, Chapter 34
is Electrical General Requirements Section E3404 is General Electrical
Requirements From Section E3404.2 you see the answer is C. The answer is
located on Page 646 of the IRC.
IRC
6. All metal faceplates should be grounded.
A. TRUE
B. FALSE
IRC
6. All metal faceplates should be grounded.
A. TRUE
B. FALSE
Keywords - Metal Faceplate From the index, Chapter 40 is Devices and
Luminaires Section E4002 is Receptacles From Section E4002.2 you see the
answer is A. The answer is located on Page 706 of the IRC.
IRC
7. Switching devices must be located less than 5 feet from the inside walls of
the pool.
A. TRUE
B. FALSE
IRC
7. Switching devices must be located less than 5 feet from the inside walls of
the pool.
A. TRUE
B. FALSE
Keywords - Switching Devices, Pool From the index, Chapter 42 is Swimming
Pools Section E4203 is Equipment Location and Clearances From Section
E4203.2 you see the answer is B. The answer is located on Page 715 of the IRC.
IRC
8. In Massachusetts, which of the following counties is not in the high radon
potential zone?
A.
B.
C.
D.
Essex
Berkshire
Middlesex
Worcester
IRC
8. In Massachusetts, which of the following counties is not in the high radon
potential zone?
A.
B.
C.
D.
Essex
Berkshire
Middlesex
Worcester
Keywords - Massachusetts, High Radon From the index, Appendix F is Radon
Control Methods From Table AF101(1) you see the answer is B. The answer is
located on Page 787 of the IRC.
IRC
9. Floor registers of vented floor furnaces shall be at least ___ inches from a
wall.
A.
B.
C.
D.
4
6
12
16
IRC
9. Floor registers of vented floor furnaces shall be at least ___ inches from a
wall.
A.
B.
C.
D.
4
6
12
16
Keywords - Vented Floor Furnace, Floor Register From the index,
Chapter 14 is Heating and Cooling Equipment Section M1408 is Vented
Floor Furnaces From Section M1408.3 you see the answer is A . The
answer is located on Page 484 of the IRC.
IRC
10. A dwelling less than 500 square feet need not have a shower.
A. TRUE
B. FALSE
IRC
10. A dwelling less than 500 square feet need not have a shower.
A. TRUE
B. FALSE
Keywords - Dwelling, Shower From the index, Chapter 3 is Building Planning
Section R306 is Sanitation From Section R306.1 you see the answer is B. The
answer is located on Page 55 of the IRC.
IRC
11. What is the minimum clearance required in front of a toilet in inches?
A.
B.
C.
D.
18
21
24
28
IRC
11. What is the minimum clearance required in front of a toilet in inches?
A.
B.
C.
D.
18
21
24
28
Keywords - Clearance, Toilet From the index, Chapter 3 is Building Planning
Section R307 is Toilet, Bath and Shower Spaces From Section R307.1 you see
the answer is B. The answer is located on Page 55 of the IRC.
IRC
12. A skylight is sloped at ___ degrees or more from vertical.
A.
B.
C.
D.
10
12
15
20
IRC
12. A skylight is sloped at ___ degrees or more from vertical.
A.
B.
C.
D.
10
12
15
20
Keywords - Skylight, Slope From the index, Chapter 3 is Building Planning Section
R308 is Glazing Section R308.6 is Skylights and Sloped Glazing, and from
Section R308.6.1 you see the answer is C. The answer is located on Page 57 of
the IRC.
IRC
13 Footings are not required to extend below the frost line when the monthly
mean temperature of the area is ___ degrees Fahrenheit .
A.
B.
C.
D.
56
62
64
68
IRC
13 Footings are not required to extend below the frost line when the monthly
mean temperature of the area is ___ degrees Fahrenheit .
A.
B.
C.
D.
56
62
64
68
Keywords - Footings, Frost From the index, Chapter 4 is Foundations Section R403 is
Footings From Section R403.3 you see the answer is C. The answer is located on
Page 78 of the IRC.
IRC
14. Subsoil storm drains shall not be less than ___ inches in diameter.
A.
B.
C.
D.
3
4
6
8
IRC
14. Subsoil storm drains shall not be less than ___ inches in diameter.
A.
B.
C.
D.
3
4
6
8
Keywords - Subsoil Drains From the index, Chapter 33 is Storm Drainage Section
P3302 is Subsoil Drains From Section P3302 you see the answer is B. The answer
is located on Page 643 of the IRC.
IBC
15. A vacation timeshare property is in Residential Group R.
A. TRUE
B. FALSE
IBC
15. A vacation timeshare property is in Residential Group R.
A. TRUE
B. FALSE
Keywords - Vacation Timeshare, Group R This is more of a global question, think
IBC. From the index, Chapter 3 is Use and Occupancy Classification Section
310 is Residential Group R From Section 310.1 you see the answer is A. The
answer is located on Page 35 of the IBC.
IBC
16. If an unsafe condition is found, the building official can deliver a written
notice by all of the following except....
A.
B.
C.
D.
by hand
certified mail
tape on door of building
registered mail
IBC
16. If an unsafe condition is found, the building official can deliver a written
notice by all of the following except....
A.
B.
C.
D.
by hand
certified mail
tape on door of building
registered mail
Keywords - Unsafe Condition, Building Official This is more of a global question,
think IBC. From the index, Chapter 1 is Scope and Administration Section R116 is
Unsafe Structures and Equipment From Section 116.4 you see the answer is C.
The answer is located on Page 9 of the IBC.
IBC
17. In a Group H-5 Building, what is the minimum width of a service corridor
must be 5 feet or ___ inches wider than the widest cart used in the corridor.
A.
B.
C.
D.
24
32
33
36
IBC
17. In a Group H-5 Building, what is the minimum width of a service corridor
must be 5 feet or ___ inches wider than the widest cart used in the corridor.
A.
B.
C.
D.
24
32
33
36
Keywords - Minimum Width, Service Corridor This is more of a global question,
think IBC. From the index, Chapter 4 is Special Detailed Requirements Section
415 is Groups H1 - H5 Section 415.8 is Groups H-5 and from Section 415.8.4.5
you see the answer is C. The answer is located on Page 71 of the IBC.
IBC
18. What is the minimum height above and below a mezzanine structure in
feet?
A.
B.
C.
D.
7
8
10
12
IBC
18. What is the minimum height above and below a mezzanine structure in
feet?
A.
B.
C.
D.
7
8
10
12
Keywords - Minimum Height, Mezzanine Structure This is more of a
global question, think IBC. From the index, Chapter 5 isGeneral
Heights and Areas Section 505 is Mezzanines From Section 505.1
you see the answer is A. The answer is located on Page 81 of the
IBC.
IBC
19 Sprayed fire resistant materials are all of the following except…
A. Cementitious
B. Asphaltic
C. Fibrous
IBC
19 Sprayed fire resistant materials are all of the following except…
A. Cementitious
B. Asphaltic
C. Fibrous
Keywords - Sprayed Fire Resistant Materials This is more of a global
question, think IBC. From the index, Chapter 17 is Structural Tests and
Inspections Section 1702 is Definitions From this Section, you see the
answer is B. The answer is located on Page 367 of the IBC.
IBC
20. A report of a geotechnical investigation must contain all of the following
except …
A.
B.
C.
D.
Location of tests
Soil profile
Temperature during test
Elevation of water table
IBC
20. A report of a geotechnical investigation must contain all of the following
except …
A.
B.
C.
D.
Location of tests
Soil profile
Temperature during test
Elevation of water table
Keywords - Geotechnical Investigation This is more of a global question, think
IBC. From the index, Chapter 18 is Soils and Foundations Section 1803 is
Geotechnical Investigations From Section 1803.6, you see the answer is C. The
answer is located on Page 389 of the IBC.
IBC
21. What is the shear value in lbs per square foot for 1/2 inch gypsum board
with framing spaced at 16" OC?
A.
B.
C.
D.
50
60
70
90
IBC
21. What is the shear value in lbs per square foot for 1/2 inch gypsum board
with framing spaced at 16" OC?
A.
B.
C.
D.
50
60
70
90
Keywords - Shear Value, Gypsum Board This is more of a global question, think
IBC. From the index, Chapter 25 is Gypsum and Plaster Section 2508 is Gypsum
Construction From Section 2508.5, you see the answer is D. The answer is located
on Page 531 of the IBC.
IBC
22. What is the maximum slope limit for safety for permanent fill ?
A.
B.
C.
D.
1 to 1
2 to 1
3 to 1
4 to 1
IBC
22. What is the maximum slope limit for safety for permanent fill ?
A.
B.
C.
D.
1 to 1
2 to 1
3 to 1
4 to 1
Keywords - Slope Limit, Permanent Fill This is more of a global question, think IBC.
From the index, Chapter 33 is Safeguards During Construction Section 3304 is
Sitework From Section 3304.1.1, you see the answer is B
Energy
Efficiency
IECC
1. What is the maximum interior design temperature used for heating load
calculations?
A.
B.
C.
D.
68
72
75
78
IECC
1. What is the maximum interior design temperature used for heating load
calculations?
A.
B.
C.
D.
68
72
75
78
Keywords - Design Temp (IECC) From the index, Chapter 3 is Design Conditions
Section 302.1 is Interior Design Conditions From the definition you see the
answer is B. The answer is located on Page 25 of the IECC.
IECC
2. What is the maximum interior design temperature used for cooling load
calculations?
A.
B.
C.
D.
68
72
75
78
IECC
2. What is the maximum interior design temperature used for cooling load
calculations?
A.
B.
C.
D.
68
72
75
78
Keywords - Design Temp (IECC) From the index, Chapter 3 is Design
Conditions Section 302.1 is Interior Design Conditions From the definition you
see the answer is C. The answer is located on Page 25 of the IECC.
IECC
3. Nebraska is located in the moist area of the US.
A. TRUE
B. FALSE
IECC
3. Nebraska is located in the moist area of the US.
A. TRUE
B. FALSE
Keywords - Nebraska, Moist Area (IECC) From the index, Section 301 is
Climate Zone. Figure 301.1 is Climate Zones From the table you see
the answer is A. The answer is located on Page 10 of the IECC.
IECC
4. What is the R Value insulation requirement for a residential floor in climate
zone 3.
A.
B.
C.
D.
13
19
30
38
IECC
4. What is the R Value insulation requirement for a residential floor in climate
zone 3.
A.
B.
C.
D.
13
19
30
38
Keywords - R value, residential, climate zone (IECC) From the index,
Section 402 is Building Thermal Envelope Table 402.1.1 is Insulation
Requirements From the table you see the answer is B. The answer is
located on Page 27 of the IECC.
IECC
5. Pools heated to more than 90 degrees F shall have a pool cover with a
minimum R value of?
A.
B.
C.
D.
8
10
12
14
IECC
5. Pools heated to more than 90 degrees F shall have a pool cover with a
minimum R value of?
A.
B.
C.
D.
8
10
12
14
Keywords - R value, Pool (IECC) From the index, Section 403.9 is Pools
Table 403.9.3 is Pool Covers From the definition you see the answer is C.
The answer is located on Page 32 of the IECC.
IECC
6. A duct tightness test is not required for an air handler if it is located in a
conditioned space.
A. TRUE
B. FALSE
IECC
6. A duct tightness test is not required for an air handler if it is located in a
conditioned space.
A. TRUE
B. FALSE
Keywords - Duct, Tightness (IECC) From the index, Section 403.2 is Ducts Table
403.2.2 is Sealing From the definition you see the answer is A . The answer is
located on Page 31 of the IECC.
IECC
7. Above grade walls are at least ___ % above grade.
A.
B.
C.
D.
50
60
70
85
IECC
7. Above grade walls are at least ___ % above grade.
A.
B.
C.
D.
50
60
70
85
Keywords - Walls, Above Grade (IECC) From the index, Section 202
is Walls From the definition you see the answer is A. The answer is
located on Page 5 of the IECC.
IECC
8. A curtain wall located in Climate Zone 3 requires a U-factor of?
A.
B.
C.
D.
0.5
0.6
0.7
1.2
IECC
8. A curtain wall located in Climate Zone 3 requires a U-factor of?
A.
B.
C.
D.
0.5
0.6
0.7
1.2
Keywords - Climate Zone 3, Curtain Wall, U-factor (IECC) From the index, Ufactor points you to 502 Table 502.3 is Building Envelope Requirements From the
table you see the answer is B. The answer is located on Page 41 of the IECC.
IECC
9. What is the minimum pipe insulation thickness in inches for a steam pipe
greater than 1.5 inches in diameter?
A.
B.
C.
D.
1.5
2
3
4
IECC
9. What is the minimum pipe insulation thickness in inches for a steam pipe
greater than 1.5 inches in diameter?
A.
B.
C.
D.
1.5
2
3
4
Keywords - Pipe insulation thickness, steam pipe (IECC) From the index,
Section 503 is Building Mechanical Systems (steam pipe) Table 503.2.8 is
Minimum Pipe Insulation From the table you see the answer is C. The answer is
located on Page 51 of the IECC.
IECC
10. Automatic lighting shutoff is required in buildings larger than ___ square
feet.
A.
B.
C.
D.
2000
5000
10000
15000
IECC
10. Automatic lighting shutoff is required in buildings larger than ___ square
feet.
A.
B.
C.
D.
2000
5000
10000
15000
Keywords - Automatic Lighting Shutoff (IECC) From the index, Section 505 is
Lighting Systems. Section 505.2.2.2 is Automatic lighting Shutoff From the definition
you see the answer is B. The answer is located on Page 58 of the IECC.
IECC
11. A skylight is a glass material installed at a slope of ___ degrees or greater.
A.
B.
C.
D.
10
12
15
20
IECC
11. A skylight is a glass material installed at a slope of ___ degrees or greater.
A.
B.
C.
D.
10
12
15
20
Keywords - Skylight (IECC) From the index, Section 202 is
Definitions From the definition you see the answer is C. The
answer is located on Page 7 of the IECC.
IECC
12. Supply ducts in attics shall be insulated to a minimum R value of?
A.
B.
C.
D.
4
6
8
10
IECC
12. Supply ducts in attics shall be insulated to a minimum R value of?
A.
B.
C.
D.
4
6
8
10
Keywords - Supply Duct, Attic, R value (IECC) From the index, Section 403.2
is Ducts and Section 403.2.1 is Insulation. From the definition you see the
answer is C. The answer is located on Page 30 of the IECC.
accessability
IRC
1. Attics containing appliances do not need a clear opening an unobstructed
passageway large enough for removal of the appliance.
A. TRUE
B. FALSE
IRC
1. Attics containing appliances do not need a clear opening an unobstructed
passageway large enough for removal of the appliance.
A. TRUE
B. FALSE
Keywords - Attic, Clear opening (access), appliance From the index, Section
M1305 is Access to Appliances Section M1305.1.3 is Appliances in Attics From
the definition you see the answer is B. The answer is located on Page 477 of the
IRC.
IRC
2. An accessory structure is a structure not greater than ___ square feet.
A.
B.
C.
D.
1,000
2,000
3,000
4,000
IRC
2. An accessory structure is a structure not greater than ___ square feet.
A.
B.
C.
D.
1,000
2,000
3,000
4,000
Keywords - Accessory Structure From the index, Section R202 is
Definitions From the definition you see the answer is C. The
answer is located on Page 9 of the IRC.
IRC
3. Plumbing fixtures with concealed slip joint connections must have an access
panel at least ___ inches in diameter.
A.
B.
C.
D.
12
18
24
36
IRC
3. Plumbing fixtures with concealed slip joint connections must have an access
panel at least ___ inches in diameter.
A.
B.
C.
D.
12
18
24
36
Keywords - Plumbing Fixture, Access Panel From the index, Section
P2704 is Access to Plumbing Connections From the definition you see
the answer is A. The answer is located on Page 595 of the IRC.
IRC
4 The location of plumbing piping, fixtures and equipment shall not interfere
with windows or doors.
A. TRUE
B. FALSE
IRC
4 The location of plumbing piping, fixtures and equipment shall not interfere
with windows or doors.
A. TRUE
B. FALSE
Keywords - Plumbing Fixture, Interfere (Access) From the index, Section P2705
is Access to Plumbing Fixtures From the definition you see the answer is A. The
answer is located on Page 595 of the IRC.
IRC
5. A vented floor furnace shall have a trap door not less than ___ square feet.
A.
B.
C.
D.
3
4.6
5
6
IRC
5. A vented floor furnace shall have a trap door not less than ___ square feet.
A.
B.
C.
D.
3
4.6
5
6
Keywords - Vented Floor Furnace, Trap Door (Access) From the
index, Chapter 14 is Heating and Cooling Equipment Section
M1408.4 is Vented Floor Furnaces Access From the definition
you see the answer is B. The answer is located on Page 484 of
the IRC.
IBC
6. At least 60% of all public entrances shall be accessible.
A. TRUE
B. FALSE
IBC
6. At least 60% of all public entrances shall be accessible.
A. TRUE
B. FALSE
Keywords - Public Entrances, Accessible This is a Global
Accessibility Question. Think IBC. From the index, Chapter 11 is
Accessibility Section 1105 is Accessible Entrances From this
Section you see the answer is A. The answer is located on Page
259 of the IBC.
IBC
7. For a parking lot with 160 spaces, ___ spaces must be accessible.
A.
B.
C.
D.
4
6
8
10
IBC
7. For a parking lot with 160 spaces, ___ spaces must be accessible.
A.
B.
C.
D.
4
6
8
10
Keywords - Parking, Accessible This is a Global Accessibility
Question. Think IBC. From the index, Chapter 11 is Accessibility
Section 1106 is Parking and Loading Facilities From this Section you
see the answer is B. The answer is located on Page 260 of the IBC.
IBC
8. In an assembly area with 75 seats, there must be ___ wheelchair spaces
under Special Occupancy.
A.
B.
C.
D.
2
3
4
6
IBC
8. In an assembly area with 75 seats, there must be ___ wheelchair spaces
under Special Occupancy.
A.
B.
C.
D.
2
3
4
6
Keywords - Assembly Area, Special Occupancy This is a Global
Accessibility Question. Think IBC. From the index, Chapter 11 is
Accessibility Section 1108 is Special Occupancy From this Section you
see the answer is C. The answer is located on Page 264 of the IBC.
Site work &
Foundation
IRC
1. Who determines if a soil test is required for a potential foundation locations?
A.
B.
C.
D.
Construction Supervisor
Building Official
Designer
Owner
IRC
1. Who determines if a soil test is required for a potential foundation locations?
A.
B.
C.
D.
Construction Supervisor
Building Official
Designer
Owner
Keywords - Soil Test, Foundation From the index, Chapter 4 is
Foundations Section R401.4 is Soil Tests From the definition you
see the answer is B. The answer is located on Page 71 of the
IRC.
IRC
2. 3,500 PSI equals ____ kPa?
A.
B.
C.
D.
7,000
1,750
507.6
24,132.50
IRC
2. 3,500 PSI equals ____ kPa?
A.
B.
C.
D.
7,000
1,750
507.6
24,132.50
Keywords - psi, kPa From the conversion factor listed in
Table R402.2, 1 psi = 6.895 kPa Calculating the conversion
gives you D. The answer is located on Page 72 of the IRC.
IRC
3. What is the minimum size of a footing of a 2-story light-frame construction
home on soil with a load bearing value of 2,000 psf?
A.
B.
C.
D.
12 in
15 in
17 in
23 in
IRC
3. What is the minimum size of a footing of a 2-story light-frame construction
home on soil with a load bearing value of 2,000 psf?
A.
B.
C.
D.
12 in
15 in
17 in
23 in
Keywords - Footing, soil From the index, Chapter 4 is Foundations
Section R403.1 is footings From the table you see the answer is A.
The answer is located on Page 72 of the IRC.
IRC
4. How should concrete be consolidated where stay-in-place forms are used
for a foundation?
A.
B.
C.
D.
With a Shovel
Internal Vibration
None Required
Tamping
IRC
4. How should concrete be consolidated where stay-in-place forms are used
for a foundation?
A.
B.
C.
D.
With a Shovel
Internal Vibration
None Required
Tamping
Keywords - Concrete, Foundation From the index, Chapter 4 is
Foundations Section R404 is Foundation and Retaining Walls From
Section R404.1.2.3.5 you see the answer is B. The answer is located
on Page 95 of the IRC.
IRC
5. Bracing is not required for wall supporting less than ____ feet of backfill.
A.
B.
C.
D.
2
3
4
5
IRC
5. Bracing is not required for wall supporting less than ____ feet of backfill.
A.
B.
C.
D.
2
3
4
5
Keywords - Bracing, Wall, Backfill From the index, Chapter 4 is
Foundations Section R404 is Foundation and Retaining Walls From
Section R404.1.7 you see the answer is C. The answer is located on Page
103 of the IRC.
IRC
6. A sump is not required in a drainage system in _____ soils.
A.
B.
C.
D.
Group 1
Group 2
Group 3
Group 4
IRC
6. A sump is not required in a drainage system in _____ soils.
A.
B.
C.
D.
Group 1
Group 2
Group 3
Group 4
Keywords - Sump, Drainage System From the index, Chapter 4 is
Foundations Section R405 is Foundation Drainage From Section
R405.2.3 you see the answer is A. The answer is located on Page
107 of the IRC.
IRC
7. Which of the following is not an acceptable concrete or foundation
waterproofing system?
A.
B.
C.
D.
6 mil PVC
60 mil Flexible Polymer Cement
Two-ply hot mopped felts
3 mil PVC
IRC
7. Which of the following is not an acceptable concrete or foundation
waterproofing system?
A.
B.
C.
D.
6 mil PVC
60 mil Flexible Polymer Cement
Two-ply hot mopped felts
3 mil PVC
Keywords - Foundation, Waterproofing From the index, Chapter 4
is Foundations Section R406 is Foundation Waterproofing and
Damp proofing From Section R406.2 you see the answer is D. The
answer is located on Page 107 of the IRC.
IRC
8. Access to under floor spaces shall be at least ____
A.
B.
C.
D.
3 sq ft
4 sq ft
5 sq ft
6 sq ft
IRC
8. Access to under floor spaces shall be at least ____
A.
B.
C.
D.
3 sq ft
4 sq ft
5 sq ft
6 sq ft
Keywords - Under floor space From the index, Section R408 is Under
Floor Spaces From Section R408.4 you see the answer is A. The answer
is located on Page 108 of the IRC.
IRC
9. What is the minimum depth to which exterior footings must be placed?
A.
B.
C.
D.
1 ft
2 ft
3 ft
4 ft
IRC
9. What is the minimum depth to which exterior footings must be placed?
A.
B.
C.
D.
1 ft
2 ft
3 ft
4 ft
Keywords - Exterior Footings From the index, Chapter 4 is
Foundations Section R403.1 is footings From Section R403.1.4 you
see the answer is A. The answer is located on Page 73 of the IRC.
IBC
10. The floor and walls must be damp proofed when the ground water level is
lowered and maintained less than 6 inches below the bottom floor
foundation
A. Yes
B. No
IBC
10. The floor and walls must be damp proofed when the ground water level is
lowered and maintained less than 6 inches below the bottom floor
foundation
A. Yes
B. No
Keywords – Damp proofed, Groundwater, Foundation This is a
Global Foundation Question. Think IBC. From the index,
Chapter 18 is Soils and Foundations Section 1805 is Damping
and Waterproofing From Section 1805.1.3 Groundwater Control
you see the answer is A. The answer is located on Page 390 of
the IBC.
IBC
11. What is the minimum slope percentage for ground directly adjacent to the
foundation?
A.
B.
C.
D.
2%
3%
5%
10%
IBC
11. What is the minimum slope percentage for ground directly adjacent to the
foundation?
A.
B.
C.
D.
2%
3%
5%
10%
Keywords - Slope, Foundation This is a Global Foundation Question.
Think IBC. From the index, Chapter 18 is Soils and Foundations
Section 1804 is Excavation, Grading and Fill From Section 1804.3 Site
Grading you see the answer is A. The answer is located on Page 389 of
the IBC.
IBC
12. Vertical reinforcement of a masonry foundation wall shall have a minimum
yield strength of ____ psi.
A.
B.
C.
D.
20,000
40,000
60,000
80,000
IBC
12. Vertical reinforcement of a masonry foundation wall shall have a minimum
yield strength of ____ psi.
A.
B.
C.
D.
20,000
40,000
60,000
80,000
Keywords - Masonry, Foundation, Yield Strength This is a Global Foundation
Question. Think IBC. From the index, Chapter 18 is Soils and Foundations
Section 1807 is Foundation Walls, Retaining Walls From Section 1807.1.6.3
Masonry Foundation Walls you see the answer is C. The answer is located on
Page 394 of the IBC.
IBC
13. What safety factor is used in the design of retaining walls?
A.
B.
C.
D.
1.5
2.5
3
3.5
IBC
13. What safety factor is used in the design of retaining walls?
A.
B.
C.
D.
1.5
2.5
3
3.5
Keywords - Safety Factor, Retaining Walls This is a Global Foundation
Question. Think IBC. From the index, Chapter 18 is Soils and
Foundations Section 1807 is Foundation Walls, Retaining Walls From
Section 1807.2.3 Safety Factor you see the answer is A. The answer
is located on Page 397 of the IBC.
IBC
14. Backfill in the annular space surrounding retaining wall columns must be
concrete with a compressive strength of at least ___ psi
A.
B.
C.
D.
2,000
3,000
4,000
5,000
IBC
14. Backfill in the annular space surrounding retaining wall columns must be
concrete with a compressive strength of at least ___ psi
A.
B.
C.
D.
2,000
3,000
4,000
5,000
Keywords - Backfill, Retaining Walls This is a Global Foundation
Question. Think IBC. From the index, Chapter 18 is Soils and
Foundations Section 1807 is Foundation Walls, Retaining Walls
From Section 1807.3.3 Backfill you see the answer is A. The
answer is located on Page 398 of the IBC.
Concrete &
Masonry
IRC
1. What is the minimum compressive strength in psi for a concrete basement
slab with negligible weathering potential.
A.
B.
C.
D.
1500
2000
2500
4000
IRC
1. What is the minimum compressive strength in psi for a concrete basement
slab with negligible weathering potential.
A.
B.
C.
D.
1500
2000
2500
4000
Keywords - Compressive Strength, Concrete Basement Slab From
the index, Chapter 4 is Foundations Section R402 is Materials
From Table R402.2 you see the answer is C. The answer is located
on Page 72 of the IRC.
IRC
2. All concrete used in precast foundations shall have a minimum compressive
strength in psi of.
A.
B.
C.
D.
2,500
4,000
5,000
6,000
IRC
2. All concrete used in precast foundations shall have a minimum compressive
strength in psi of.
A.
B.
C.
D.
2,500
4,000
5,000
6,000
Keywords - Precast Foundation, Compressive Strength From the
index, Chapter 4 is Foundations Section R402 is Materials From
Section R402.3.1 you see the answer is C. The answer is located on
Page 72 of the IRC.
IRC
3. For a below grade concrete floor, the 4 inches of base course must pass a
__ inch sieve.
A.
B.
C.
D.
1
2
3
4
IRC
3. For a below grade concrete floor, the 4 inches of base course must pass a
__ inch sieve.
A.
B.
C.
D.
1
2
3
4
Keywords - Concrete Floor, Below Grade From the index, Section R506
is Concrete Floors From Section 506.2.2 you see the answer is B. The
answer is located on Page 144 of the IRC.
IRC
4. The slump of concrete placed in removable forms shall not exceed _ inches.
A.
B.
C.
D.
3
4
6
8
IRC
4. The slump of concrete placed in removable forms shall not exceed _ inches.
A.
B.
C.
D.
3
4
6
8
Keywords - Concrete, Removable Forms From the index, Chapter 4
is Foundations Section R404 is Foundation and Retaining Walls
From Section R404.1.2.3.4 you see the answer is C. The answer is
located on Page 95 of the IRC.
IRC
5. What is the minimum thickness of a rubble stone masonry wall in inches.
A.
B.
C.
D.
8
12
16
18
IRC
5. What is the minimum thickness of a rubble stone masonry wall in inches.
A.
B.
C.
D.
8
12
16
18
Keywords - Rubble Stone Masonry From the index, Section R606 is
General Masonry Section R606.2.2 is Rubble Stone Masonry From
this Section you see the answer is C. The answer is located on Page
261 of the IRC.
IRC
6. What is the minimum thickness of a masonry bearing wall more than onestory high in inches.
A.
B.
C.
D.
8
12
16
18
IRC
6. What is the minimum thickness of a masonry bearing wall more than onestory high in inches.
A.
B.
C.
D.
8
12
16
18
Keywords - Masonry Bearing Wall, Minimum Thickness From the index,
Section R606 is General Masonry Section R606.2.1 is Minimum
Thickness From this Section you see the answer is A. The answer is
located on Page 261 of the IRC.
IRC
7. Chases and recesses in masonry walls shall not be deeper than ___ of the
wall thickness.
A.
B.
C.
D.
one quarter
one third
one half
two thirds
IRC
7. Chases and recesses in masonry walls shall not be deeper than ___ of the
wall thickness.
A.
B.
C.
D.
one quarter
one third
one half
two thirds
Keywords - Chases, Masonry From the index, Section R606 is
General Masonry Section R606.7 is Chases From this Section you
see the answer is B. The answer is located on Page 282 of the
IRC.
IRC
8. Masonry over openings can be supported by all of the following except.
A.
B.
C.
D.
Steel lintels
Reinforced concrete
Grade 3 lumber
masonry arches
IRC
8. Masonry over openings can be supported by all of the following except.
A.
B.
C.
D.
Steel lintels
Reinforced concrete
Grade 3 lumber
masonry arches
Keywords - Masonry over Openings (Lintels) From the index, Section
R606 is General Masonry Section R606.10 is Lintels From this Section
you see the answer is C. The answer is located on Page 263 of the
IRC.
IRC
9. When connecting a joist to a masonry wall, the bolt must be embedded at
least ___ inches into the masonry wall.
A.
B.
C.
D.
2
3
4
6
IRC
9. When connecting a joist to a masonry wall, the bolt must be embedded at
least ___ inches into the masonry wall.
A.
B.
C.
D.
2
3
4
6
Keywords - Masonry, Joist, Bolt From the index, Section R606 is General
Masonry Section R606.11 is Anchorage From this Section you see the
answer is C. The answer is located on Page 263 of the IRC.
IRC
10. Grout for masonry shall consist of cementitious material and aggregate.
A. Yes
B. No
IRC
10. Grout for masonry shall consist of cementitious material and aggregate.
A. Yes
B. No
Keywords - Masonry, Grout From the index, Section R606 is General
Masonry Section R609 is Grouted Masonry From this Section you
see the answer is A. The answer is located on Page 271 of the IRC.
IRC
11. What is the minimum reinforcing bar size for an 8 inch stacked bonded
masonry wall?
A.
B.
C.
D.
#3
#4
#5
#6
IRC
11. What is the minimum reinforcing bar size for an 8 inch stacked bonded
masonry wall?
A.
B.
C.
D.
#3
#4
#5
#6
Keywords - Rebar, Bonded Masonry Wall From the index, Section R606 is
General Masonry Section R606 is General Masonry Construction and Table
R606.12.4.2 From this Table you see the answer is C. The answer is
located on Page 269 of the IRC.
IRC
12. Pier Caps shall be capped with ___ inches of solid masonry.
A.
B.
C.
D.
2
4
6
8
IRC
12. Pier Caps shall be capped with ___ inches of solid masonry.
A.
B.
C.
D.
2
4
6
8
Keywords - Pier Cap, Masonry From the index, Section R606 is General
Masonry Section R606.6.1 is Pier Cap From this Section you see the
answer is B. The answer is located on Page 262 of the IRC.
IBC
13. For concrete weathering probability, South Carolina is located in the ___
zone.
A. Severe
B. Moderate
C. Negligible
IBC
13. For concrete weathering probability, South Carolina is located in the ___
zone.
A. Severe
B. Moderate
C. Negligible
Keywords - Concrete Weathering This is a Global Concrete Question. Think
IBC. From the index, Chapter 19 is Concrete Section 1904 is Durability
Requirements From Section Figure 1904.3 you see the answer is B. The
answer is located on Page 417 of the IBC.
IBC
14. When using shotcrete, what is the maximum size of reinforcing bars?
A.
B.
C.
D.
No. 3
No. 4
No. 5
No. 6
IBC
14. When using shotcrete, what is the maximum size of reinforcing bars?
A.
B.
C.
D.
No. 3
No. 4
No. 5
No. 6
IBC
15. When taking strength tests of shotcrete, a sample must be taken at least
every ___ yards.
A.
B.
C.
D.
10
15
20
50
IBC
15. When taking strength tests of shotcrete, a sample must be taken at least
every ___ yards.
A.
B.
C.
D.
10
15
20
50
IBC
16. What is the allowable shear in lbs for a 1 inch bolt embedded 21 inches
into adobe masonry.
A.
B.
C.
D.
300
400
500
600
IBC
16. What is the allowable shear in lbs for a 1 inch bolt embedded 21 inches
into adobe masonry.
A.
B.
C.
D.
300
400
500
600
IBC
17. An interior masonry fireplace must have a clearance to combustibles of not
less than ___ inches.
A.
B.
C.
D.
2
3
4
6
IBC
17. An interior masonry fireplace must have a clearance to combustibles of not
less than ___ inches.
A.
B.
C.
D.
2
3
4
6
IBC
18 Hot weather construction provisions for masonry should be applied when
the temperature exceeds ___ degrees Fahrenheit.
A.
B.
C.
D.
85
90
95
100
IBC
18 Hot weather construction provisions for masonry should be applied when
the temperature exceeds ___ degrees Fahrenheit.
A.
B.
C.
D.
85
90
95
100
Moisture intrusion &
Protection
IRC
1. Vapor retarders are required on the interior side of basement walls in Zones
5,6,7,8 and Marine 4.
A. TRUE
B. FALSE
IRC
1. Vapor retarders are required on the interior side of basement walls in Zones
5,6,7,8 and Marine 4.
A. TRUE
B. FALSE
Keywords - Vapor Retarder, Basement Wall From the index, Section R601 is
Vapor Retarders From this Section, you see the answer is B. The answer is
located on Page 145 of the IRC.
IRC
2. Which of the following does not meet material vapor retarder class
specifications .
A.
B.
C.
D.
Sheet polyethylene
Fiberglass Batts
Oil based paint
Latex Paint
IRC
2. Which of the following does not meet material vapor retarder class
specifications .
A.
B.
C.
D.
Sheet polyethylene
Fiberglass Batts
Oil based paint
Latex Paint
Keywords - Vapor Retarder, Class From the index, Section R601 is Vapor
Retarders Section 601.3.2 is Material Class From this Section, you see the
answer is C. The answer is located on Page 145 of the IRC.
IRC
3. Spray foam applied to the interior cavity side shall have a minimum density
of ___ lb per cubic foot to meet the insulating sheathing requirement .
A.
B.
C.
D.
2
3
4
6
IRC
3. Spray foam applied to the interior cavity side shall have a minimum density
of ___ lb per cubic foot to meet the insulating sheathing requirement .
A.
B.
C.
D.
2
3
4
6
Keywords - Spray Foam, Insulating Sheathing From the index,
Section R601 is Vapor Retarders Table 601.3.1 is Class III
Vapor Retarders From the footnote of this Table, you see the
answer is A. The answer is located on Page 145 of the IRC.
IRC
4. Vapor retarders are not required on below grade walls in Zones 5,6,7,8 and
Marine 4 .
A. TRUE
B. FALSE
IRC
4. Vapor retarders are not required on below grade walls in Zones 5,6,7,8 and
Marine 4 .
A. TRUE
B. FALSE
Keywords - Vapor Retarder, Wall From the index, Section R601 is Vapor
Retarders From this Section, you see the answer is A . The answer is located on
Page 145 of the IRC.
IRC
5. In zone 5, class III vapor retarders are permitted for all of the following
except ...
A.
B.
C.
D.
Vented cladding over OSB
Vented cladding over plywood
Vented cladding over sheathing
Vented cladding over gypsum
IRC
5. In zone 5, class III vapor retarders are permitted for all of the following
except ...
A.
B.
C.
D.
Vented cladding over OSB
Vented cladding over plywood
Vented cladding over sheathing
Vented cladding over gypsum
Keywords - Vapor Retarder From the index, Section R601 is Vapor Retarders
Table 601.3.1 is Class III Vapor Retarders From this Table, you see the
answer is C. The answer is located on Page 145 of the IRC.
IRC
6. Vapor retarders are not required where moisture or freezing will not damage
the materials in Zones 5,6,7,8 and Marine 4.
A. TRUE
B. FALSE
IRC
6. Vapor retarders are not required where moisture or freezing will not damage
the materials in Zones 5,6,7,8 and Marine 4.
A. TRUE
B. FALSE
Keywords - Vapor Retarder From the index, Section R601 is Vapor
Retarders From this Section, you see the answer is A. The answer
is located on Page 145 of the IRC.
IRC
7. Which of the following is not an acceptable concrete or foundation
waterproofing system?
A.
B.
C.
D.
6 mil PVC
60 mil Flexible Polymer Cement
Two-ply hot mopped felts
3 mil PVC
IRC
7. Which of the following is not an acceptable concrete or foundation
waterproofing system?
A.
B.
C.
D.
6 mil PVC
60 mil Flexible Polymer Cement
Two-ply hot mopped felts
3 mil PVC
Keywords - Foundation Waterproofing System From the index, Section
R406 is Foundation Waterproofing Section R406.2 is Concrete and
Masonry Waterproofing and Dampproofing From this Section, you see the
answer is D. The answer is located on Page 107 of the IRC.
IRC
8. For dampproofing, masonry walls shall not have less than ___ inches of
portland cement parging applied to the exterior of the wall.
A.
B.
C.
D.
(1/4)
(1/2)
(3/4)
(3/8)
IRC
8. For dampproofing, masonry walls shall not have less than ___ inches of
portland cement parging applied to the exterior of the wall.
A.
B.
C.
D.
(1/4)
(1/2)
(3/4)
(3/8)
Keywords - Damproofing, Masonry From the index, Section R406 is Foundation
Waterproofing Section R406.2 is Concrete and Masonry Waterproofing and
Dampproofing From this Section, you see the answer is D. The answer is
located on Page 107 of the IRC.
IRC
9. Polyethylene film applied for below grade moisture barriers must be
overlapped by _ inches .
A.
B.
C.
D.
3
6
12
18
IRC
9. Polyethylene film applied for below grade moisture barriers must be
overlapped by _ inches .
A.
B.
C.
D.
3
6
12
18
Keywords - Below Grade Moisture From the index, Section R406 is
Foundation Waterproofing Section R406.3.2 is Below Grade Moisture
Barrier From this Section, you see the answer is B. The answer is
located on Page 107 of the IRC.
IBC
10. Built in tubs with showers do not need waterproof joints between the tub
and the wall.
A. TRUE
B. FALSE
IBC
10. Built in tubs with showers do not need waterproof joints between the tub
and the wall.
A. TRUE
B. FALSE
Keywords - Showers, Waterproof Joints This is more of a global
question, think IBC. From the index, Chapter 12 is Interior
Environment Section 1210 is Surrounding Materials From Section
1210.4 you see the answer is B. The answer is located on Page 274
of the IBC.
IBC
11. Exterior wall envelope test assemblies shall be at least ___ square feet .
A.
B.
C.
D.
24
32
36
42
IBC
11. Exterior wall envelope test assemblies shall be at least ___ square feet .
A.
B.
C.
D.
24
32
36
42
Keywords - Exterior Wall Envelope This is more of a global question, think
IBC. From the index, Chapter 14 is Exterior Walls Section 1403 is
Performance Requirements From Section 1403.2 you see the answer is B.
The answer is located on Page 277 of the IBC
IBC
12. Roof flashing shall have a minimum thickness of ___ inches .
A.
B.
C.
D.
0.015
0.019
0.025
0.030
IBC
12. Roof flashing shall have a minimum thickness of ___ inches .
A.
B.
C.
D.
0.015
0.019
0.025
0.030
Keywords - Roof Flashing This is more of a global question, think IBC.
From the index, Chapter 15 is Roofing Section 1503 is Weather Protection
From Section 1503.2 you see the answer is B. The answer is located on
Page 288 of the IBC
IBC
13. Fire retardant treated wood shall be dried to a moisture content of ___ %
or less for structural panels .
A.
B.
C.
D.
12
15
19
22
IBC
13. Fire retardant treated wood shall be dried to a moisture content of ___ %
or less for structural panels .
A.
B.
C.
D.
12
15
19
22
Keywords - Fire Retardant Wood, Moisture Content This is more of a global
question, think IBC. From the index, Chapter 23 is Wood Section 2303 is
Minimum Standards and Quality Section 2303.2 is Fire Retardant Treated Wood
and from Section 2303.2.7 you see the answer is B. The answer is located on
Page 454 of the IBC
IBC
14. Dampproofing beneath a floor slab must be at least....
A.
B.
C.
D.
3-mil
4-mil
6-ml
8-mil
IBC
14. Dampproofing beneath a floor slab must be at least....
A.
B.
C.
D.
3-mil
4-mil
6-ml
8-mil
Keywords - Dampproofing, Floor Slab This is more of a global question,
think IBC. From the index, Chapter 18 is Foundations Section 1805 is
Dampproofing and Waterproofing Section 1805.2 is Dampproofing and
from Section 1805.2.1 you see the answer is C. The answer is located
on Page 390 of the IBC
Structural Framing
Steel & wood
IRC
1. Load bearing cold fomed structural steel framing wall members shall not
have the following info stamped.
A.
B.
C.
D.
Manufacturer
Minimum Coating Designation
Minimum Length
Minimum yield strength
IRC
1. Load bearing cold fomed structural steel framing wall members shall not
have the following info stamped.
A.
B.
C.
D.
Manufacturer
Minimum Coating Designation
Minimum Length
Minimum yield strength
Keywords - Steel framing, wall, load bearing From the index, Chapter 6
is Wall Construction Section R603.2 is Structural Framing From Section
R603.2.2 you see the answer is C. The answer is located on Page 188
of the IRC.
IRC
2. What is the minimum screw size for fastening gypsum board to a cold
formed structural steel wall?
A.
B.
C.
D.
No. 5
No. 6
No. 7
No. 8
IRC
2. What is the minimum screw size for fastening gypsum board to a cold
formed structural steel wall?
A.
B.
C.
D.
No. 5
No. 6
No. 7
No. 8
Keywords - Screw, wall, gypsum, structural From the index,
Chapter 6 is Wall Construction Section R603.2 is Structural
Framing From Section R603.2.4 you see the answer is B. The
answer is located on Page 188 of the IRC.
IRC
3. Flanges and lips of load bearing cold formed steel roof framing members
can be cut or notched if approved by the engineer.
A. TRUE
B. FALSE
IRC
3. Flanges and lips of load bearing cold formed steel roof framing members
can be cut or notched if approved by the engineer.
A. TRUE
B. FALSE
Keywords - Flanges, Lips, steel roof From the index, Chapter 8 is Roof-Ceiling
Construction Section R804 is Steel Roof Framing Section R804.3 is Roof
Construction, and from Section R804.3.4 you see the answer is B. The
answer is located on Page 420 of the IRC.
IRC
4. Wall ties must be used on a structural steel roof assembly when the wind
uplift pressure is greater than ___ pounds per square foot? .
A.
B.
C.
D.
15
20
25
30
IRC
4. Wall ties must be used on a structural steel roof assembly when the wind
uplift pressure is greater than ___ pounds per square foot? .
A.
B.
C.
D.
15
20
25
30
Keywords - Structural steel roof, wind From the index, Chapter 8 is Roof-Ceiling
Construction Section R804 is Steel Roof Framing Section R804.3 is Roof
Construction, and from Section R804.3.9 you see the answer is B. The answer
is located on Page 421 of the IRC.
IRC
5. In a braced wall line using 1/2 inch gypsum board, what is the minimum
spacing for nails and screws to be installed in inches .
A.
B.
C.
D.
7
8
12
16
IRC
5. In a braced wall line using 1/2 inch gypsum board, what is the minimum
spacing for nails and screws to be installed in inches .
A.
B.
C.
D.
7
8
12
16
Keywords - Braced wall, gypsum, spacing From the index, Chapter 6 is Wall
Construction Section R602 is Wood Wall Framing Section R602.10 is Wall
Bracing, and from Section R602.10.2 you see the answer is A. The answer is
located on Page 166 of the IRC.
IRC
6. What is the minimum length in inches of a structural fiberboard braced wall
panel on a 10 foot wall with a 85% opening clear height?
A.
B.
C.
D.
24
30
40
60
IRC
6. What is the minimum length in inches of a structural fiberboard braced wall
panel on a 10 foot wall with a 85% opening clear height?
A.
B.
C.
D.
24
30
40
60
Keywords - Braced wall, fiberboard, structural From the index, Chapter 6 is Wall
Construction Section R602 is Wood Wall Framing Section R602.10 is Wall
Bracing, and from Table R602.10.5.2 you see the answer is A . The answer is
located on Page 180 of the IRC.
IRC
7. Steel Gable end walls less than 10 feet high must be anchored to the
foundation or floor.
A. TRUE
B. FALSE
IRC
7. Steel Gable end walls less than 10 feet high must be anchored to the
foundation or floor.
A. TRUE
B. FALSE
Keywords - Steel, gable end wall From the index, Chapter 6 is Wall
Construction Section R603 is Steel Wall Framing Section R603.3 is Wall
Construction, and from Section R603.3.1.1 you see the answer is B. The
answer is located on Page 191 of the IRC.
IRC
8. On a steel wall, OSB structural sheathing materials shall be a minimum of
___ inches thick.
A.
B.
C.
D.
(3/8)
(7/16)
(3/4)
(1/2)
IRC
8. On a steel wall, OSB structural sheathing materials shall be a minimum of
___ inches thick.
A.
B.
C.
D.
(3/8)
(7/16)
(3/4)
(1/2)
Keywords - Steel wall, OSB, Structural From the index, Chapter 6 is
Wall Construction Section R603 is Steel Wall Framing Section
R603.9 is Structural Sheathing, and from Section R603.9.1 you see
the answer is B. The answer is located on Page 195 of the IRC.
IRC
9. Steel framing members shall be replaced or special designed when the hole
exceeds ___% of the flat width of the web .
A.
B.
C.
D.
40
50
60
70
IRC
9. Steel framing members shall be replaced or special designed when the hole
exceeds ___% of the flat width of the web .
A.
B.
C.
D.
40
50
60
70
Keywords - Steel framing, hole From the index, Chapter 6 is Wall
Construction Section R603 is Steel Wall Framing Section R603.2 is
Structural Framing, and from Section R603.2.5.3 you see the answer is D.
The answer is located on Page 190 of the IRC.
IRC
10. Load bearing steel framing can be shaped with steel complying with all of
these ASTMs except .
A.
B.
C.
D.
563
653
792
1,003
IRC
10. Load bearing steel framing can be shaped with steel complying with all of
these ASTMs except .
A.
B.
C.
D.
563
653
792
1,003
Keywords - Load bearing, Steel framing From the index, Chapter 6 is Wall
Construction Section R603 is Steel Wall Framing Section R603.2 is Structural
Framing, and from Section R603.2.1 you see the answer is A . The answer is
located on Page 188 of the IRC.
IRC
11. What is the maximum length of a penetration of a structural steel member?
A.
B.
C.
D.
3 in
3.5 in
4 in
4.5 in
IRC
11. What is the maximum length of a penetration of a structural steel member?
A.
B.
C.
D.
3 in
3.5 in
4 in
4.5 in
Keywords - Structural steel From the index, Chapter 6 is Wall Construction
Section R603 is Steel Wall Framing Section R603.2 is Structural Framing,
and from Section R603.2.5.1 you see the answer is D. The answer is located
on Page 190 of the IRC.
IRC
12. What is the minimum base steel thickness for a 43 mil structural steel
member?
A.
B.
C.
D.
0.0329
0.0538
0.0428
0.0966
IRC
12. What is the minimum base steel thickness for a 43 mil structural steel
member?
A.
B.
C.
D.
0.0329
0.0538
0.0428
0.0966
Keywords - Structural steel From the index, Chapter 6 is Wall
Construction Section R603 is Steel Wall Framing Section R603.2 is
Structural Framing, and from Table R603.2(2) you see the answer is C.
The answer is located on Page 189 of the IRC.
IRC
13. What is the center to center spacing of web holes in steel wall studs?
A.
B.
C.
D.
12 in
16 in
20 in
24 in
IRC
13. What is the center to center spacing of web holes in steel wall studs?
A.
B.
C.
D.
12 in
16 in
20 in
24 in
Keywords - Steel wall From the index, Chapter 6 is Wall Construction Section R603 is
Steel Wall Framing Section R603.2 is Structural Framing, and from Section
R603.2.5.1 you see the answer is D. The answer is located on Page 190 of the IRC.
IRC
14. Lintels shall be provided for all openings greater than ___ feet in width.
A.
B.
C.
D.
2
3
4
6
IRC
14. Lintels shall be provided for all openings greater than ___ feet in width.
A.
B.
C.
D.
2
3
4
6
Keywords - Lintel, openings From the index, Chapter 6 is Wall Construction
Section R611 is Exterior Concrete Wall Construction Section R611.8 is
Requirements for Lintel openings, and from Section R611.8.2 you see the
answer is A. The answer is located on Page 303 of the IRC.
IRC
15. Load bearing headers are not required in interior nonbearing wood walls.
A. TRUE
B. FALSE
IRC
15. Load bearing headers are not required in interior nonbearing wood walls.
A. TRUE
B. FALSE
Keywords - Load bearing headers, wood walls From the index, Chapter 6 is
Wall Construction Section R602 is Wood Wall Framing Section R602.7 is
Headers, and from Section R602.7.2 you see the answer is A. The answer
is located on Page 157 of the IRC.
IRC
16. What is the recommended fastener spacing for built up corner studs in a
wood wall?
A.
B.
C.
D.
12" OC
16" OC
20" OC
24" OC
IRC
16. What is the recommended fastener spacing for built up corner studs in a
wood wall?
A.
B.
C.
D.
12" OC
16" OC
20" OC
24" OC
Keywords - Fastener spacing, wood wall From the index, Chapter 6 is Wall Construction
Section R602 is Wood Wall Framing Section R602.3 is Design and Construction, and
from Table R602.3(1) you see the answer is D. The answer is located on Page 153 of
the IRC.
IRC
17. What is the maximum tolerance for in line framing of steel studs?
A.
B.
C.
D.
1/4 inch
1/2 inch
3/4 inch
1 inch
IRC
17. What is the maximum tolerance for in line framing of steel studs?
A.
B.
C.
D.
1/4 inch
1/2 inch
3/4 inch
1 inch
Keywords - Tolerance, In Line Framing, Steel From the index, Chapter 6 is
Wall Construction Section R603 is Steel Wall Framing Section R603.1 is
General, and from Section R603.1.2 you see the answer is C. The answer
is located on Page 187 of the IRC.
IBC
18. Combustible wood framing shall be a minimum of ___ inches from flues
and chimneys.
A.
B.
C.
D.
2
3
4
6
IBC
18. Combustible wood framing shall be a minimum of ___ inches from flues
and chimneys.
A.
B.
C.
D.
2
3
4
6
Keywords - Combustible Wood Framing, Chimneys This is more of a global
question, think IBC. From the index, Chapter 23 is Wood Section 2304 is
General Construction Requirements From Section 2304.5 you see the
answer is A. The answer is located on Page 456 of the IBC.
IBC
19. Cold Formed floor and roof steel framing shall be in accordance with which
of the following .
A.
B.
C.
D.
AISI S200
AISI S150
AISI S210
AISI S300
IBC
19. Cold Formed floor and roof steel framing shall be in accordance with which
of the following .
A.
B.
C.
D.
AISI S200
AISI S150
AISI S210
AISI S300
Keywords - Steel Framing This is more of a global question, think IBC.
From the index, Chapter 22 is Steel Section 2210 is Cold Formed Steel
Light Frame Construction From Section 2210.5 you see the answer is C.
The answer is located on Page 449 of the IBC.
IBC
20. A registered design professional must be consulted for cold formed steel
trusses spanning __ feet or greater .
A.
B.
C.
D.
30
40
50
60
IBC
20. A registered design professional must be consulted for cold formed steel
trusses spanning __ feet or greater .
A.
B.
C.
D.
30
40
50
60
Keywords - Cold Formed Steel Trusses This is more of a global question,
think IBC. From the index, Chapter 22 is Steel Section 2210 is Cold Formed
Steel Light Frame Construction Section 2210.3 is Trusses and from Section
2210.3.4 you see the answer is D. The answer is located on Page 449 of the
IBC.
IBC
21. Special loads for steel joists include all of the following except .
A.
B.
C.
D.
Bending moments
End moments
Concentrated loads
Non-uniform loads
IBC
21. Special loads for steel joists include all of the following except .
A.
B.
C.
D.
Bending moments
End moments
Concentrated loads
Non-uniform loads
Keywords - Steel Joists, Special Loads This is more of a global question,
think IBC. From the index, Chapter 22 is Steel Section 2206 is Steel Joists
From Section 2206.2 you see the answer is A. The answer is located on
Page 448 of the IBC.
IBC
22. Steel placement plans need not include…
A.
B.
C.
D.
Applicable loads
Deflection criteria
Joist Headers
Design professional signature
IBC
22. Steel placement plans need not include…
A.
B.
C.
D.
Applicable loads
Deflection criteria
Joist Headers
Design professional signature
Keywords - Steel Placement Plan This is more of a global question, think
IBC. From the index, Chapter 22 is Steel Section 2206 is Steel Joists
From Section 2206.4 you see the answer is D. The answer is located on
Page 448 of the IBC.
IBC
23. Prescriptive framing for cold formed steel includes detached 1 and 2 family
dwellings and townhouses.
A. TRUE
B. FALSE
IBC
23. Prescriptive framing for cold formed steel includes detached 1 and 2 family
dwellings and townhouses.
A. TRUE
B. FALSE
Keywords - Prescriptive Steel Framing This is more of a global question,
think IBC. From the index, Chapter 22 is Steel Section 2210 is Cold
Formed Steel Light Frame Construction From Section 2210.7 you see
the answer is A. The answer is located on Page 449 of the IBC.
IBC
24. Framing members for each individual pane of glass must have a deflection
of less than ___ of the glass edge length .
A.
B.
C.
D.
(1/100)
(1/150)
(1/175)
(1/200)
IBC
24. Framing members for each individual pane of glass must have a deflection
of less than ___ of the glass edge length .
A.
B.
C.
D.
(1/100)
(1/150)
(1/175)
(1/200)
Keywords - Framing Members, Glass This is more of a global question, think
IBC. From the index, Chapter 24 is Glass and Glazing Section 2403 is
General Requirements for Glass From Section 2403.3 you see the answer is
C. The answer is located on Page 521 of the IBC.
IBC
25. An example of a structural composite lumber is ...
A.
B.
C.
D.
LVL
2x6
2x8
2 x 12
IBC
25. An example of a structural composite lumber is ...
A.
B.
C.
D.
LVL
2x6
2x8
2 x 12
Keywords - Structural Composite Lumber This is more of a global
question, think IBC. From the index, Chapter 23 is Wood Section 2302
is Definitions From this Section, you see the answer is A . The answer
is located on Page 452 of the IBC.
IBC
26. Structural log members must have a grade mark of an approved lumber
grading agency.
A. TRUE
B. FALSE
IBC
26. Structural log members must have a grade mark of an approved lumber
grading agency.
A. TRUE
B. FALSE
Keywords - Structural Log Members, Grade Mark This is more of a global
question, think IBC. From the index, Chapter 23 is Wood Section 2303.1
is Minimum Standards and Quality Section 2303.1 is General and from
Section 2303.1.10 you see the answer is A. The answer is located on
Page 453 of the IBC.
Doors & Windows
IRC
1. How many egress doors must be provided for each dwelling unit?
A.
B.
C.
D.
1
2
3
4
IRC
1. How many egress doors must be provided for each dwelling unit?
A.
B.
C.
D.
1
2
3
4
Keywords - Egress, Doors From the index, Chapter 3 is Building Planning
Section R311 is Egress From Section R311.2 you see the answer is A. The
answer is located on Page 59 of the IRC.
IRC
2. What is the minimum length of the landing on either side of an exterior
door?
A.
B.
C.
D.
20 in
24 in
36 in
48 in
IRC
2. What is the minimum length of the landing on either side of an exterior
door?
A.
B.
C.
D.
20 in
24 in
36 in
48 in
Keywords - Landing, exterior door From the index, Chapter 3 is
Building Planning Section R311 is Egress From Section R311.3 you
see the answer is C. The answer is located on Page 59 of the IRC.
IRC
3. Storm and screen doors are permitted to swing over exterior stairs ?
A. TRUE
B. FALSE
IRC
3. Storm and screen doors are permitted to swing over exterior stairs ?
A. TRUE
B. FALSE
Keywords - Storm Doors, stairs From the index, Chapter 3 is
Building Planning Section R311 is Egress From Section
R311.3.3.3 you see the answer is A. The answer is located on
Page 59 of the IRC.
IRC
4. Release of a window opening device shall require no more than ____
pounds of force.
A.
B.
C.
D.
10
12
15
20
IRC
4. Release of a window opening device shall require no more than ____
pounds of force.
A.
B.
C.
D.
10
12
15
20
Keywords - Window opening device In the IRC, Exterior Windows and Doors fall
under Wall Construction. From the index, Chapter 6 is Wall Construction Section
R612 is Exterior Windows and Doors Section R612.4 is Window Opening limiting
devices, and from Section R612.4.2 you see the answer is C. The answer is
located on Page 345 of the IRC.
IRC
5. What is the structural safety factor for mullions?
A.
B.
C.
D.
1.5
2
2.5
3
IRC
5. What is the structural safety factor for mullions?
A.
B.
C.
D.
1.5
2
2.5
3
Keywords - Safety Factor, Mullions In the IRC, Exterior Windows and
Doors fall under Wall Construction. From the index, Chapter 6 is Wall
Construction Section R612 is Exterior Windows and Doors Section
R612.11 is Mullions, and from Section R612.11.3 you see the answer is A.
The answer is located on Page 348 of the IRC.
IRC
6. Decorative glazed windows and doors must be tested by an approved
independent laboratory.
A. TRUE
B. FALSE
IRC
6. Decorative glazed windows and doors must be tested by an approved
independent laboratory.
A. TRUE
B. FALSE
Keywords - Glazed windows and doors In the IRC, Exterior Windows and
Doors fall under Wall Construction. From the index, Chapter 6 is Wall
Construction Section R612 is Exterior Windows and Doors From Section
R612.6 you see the answer is B. The answer is located on Page 345 of the
IRC.
IRC
7. Windows and glass doors can be anchored through all of the following
except...
A.
B.
C.
D.
frame
frame clip
flange opening
substrate
IRC
7. Windows and glass doors can be anchored through all of the following
except...
A.
B.
C.
D.
frame
frame clip
flange opening
substrate
Keywords - Windows and glass doors, Anchored In the IRC, Exterior
Windows and Doors fall under Wall Construction. From the index,
Chapter 6 is Wall Construction Section R612 is Exterior Windows and
Doors Section R612.10 is Anchorage Methods, and from Section
R612.10.2.2 you see the answer is D. The answer is located on Page
347 of the IRC.
IBC
8. For a Means of Egress Door, what is the minimum width of each door
opening in inches?
A.
B.
C.
D.
24
28
32
36
IBC
8. For a Means of Egress Door, what is the minimum width of each door
opening in inches?
A.
B.
C.
D.
24
28
32
36
Keywords - Means of Egress door, minimum width This is more of a global
question, think IBC. From the index, Chapter 10 is Means of Egress Section 1008
is Doors, Gates and Turnstiles From Section 1008.1.1 you see the answer is C.
The answer is located on Page 224 of the IBC.
IBC
9. What is the minimum distance between two doors in a series in inches?
A.
B.
C.
D.
36
48
60
72
IBC
9. What is the minimum distance between two doors in a series in inches?
A.
B.
C.
D.
36
48
60
72
Keywords - Doors, minimum distance This is more of a global question,
think IBC. From the index, Chapter 10 is Means of Egress Section 1008 is
Doors, Gates and Turnstiles From Section 1008.1.8 you see the answer is
B. The answer is located on Page 227 of the IBC.
IBC
10. What is the minimum horizontal area of an emergency window well in
square feet?
A.
B.
C.
D.
6
8
9
12
IBC
10. What is the minimum horizontal area of an emergency window well in
square feet?
A.
B.
C.
D.
6
8
9
12
Keywords - Emergency window, minimum horizontal area This is more of a
global question, think IBC. From the index, Chapter 10 is Means of Egress
Section 1029 is Emergency Escape and Rescue From Section 1029.5.1
you see the answer is C. The answer is located on Page 255 of the IBC
IBC
11. When considering lighting, what is the minimum net glazed area shall not
be less than ___ percent of the floor area of the room served.
A.
B.
C.
D.
8
10
15
25
IBC
11. When considering lighting, what is the minimum net glazed area shall not
be less than ___ percent of the floor area of the room served.
A.
B.
C.
D.
8
10
15
25
Keywords - floor area, minimum net glazed area This is more of a global
question, think IBC. From the index, Chapter 12 is Interior Environment
Section 1205 is Lighting From Section 1205.2 you see the answer is A. The
answer is located on Page 272 of the IBC
Roofing &
Exterior walls
IRC
1. Exterior wood framing walls shall be a minimum of ___ grade wood .
A.
B.
C.
D.
Utility
2
3
4
IRC
1. Exterior wood framing walls shall be a minimum of ___ grade wood .
A.
B.
C.
D.
Utility
2
3
4
Keywords - Wood Framing, Grade From the index, Chapter 6 is Wall
Construction Section R602 is Wood Wall Framing From Section R602.2
Grade, you see the answer is C. The answer is located on Page 146 of
the IRC.
IRC
2 Any stud in an exterior wall may be notched to a depth not exceeding ___
percent of the width of the stud.
A.
B.
C.
D.
15
20
25
30
IRC
2 Any stud in an exterior wall may be notched to a depth not exceeding ___
percent of the width of the stud.
A.
B.
C.
D.
15
20
25
30
Keywords - Exterior Wall, notched From the index, Chapter 6 is Wall
Construction Section R602 is Wood Wall Framing From Section R602.6
Grade, you see the answer is C. The answer is located on Page 155 of
the IRC.
IRC
3. Galvanized fasteners shall be used for attaching metal roof panels to
supports .
A. TRUE
B. FALSE
IRC
3. Galvanized fasteners shall be used for attaching metal roof panels to
supports .
A. TRUE
B. FALSE
Keywords - Fasteners, Metal Roof Panels From the index, Chapter 9 is Roof
Assemblies Section R905 is Requirements for Roof Coverings Section
905.10 is Metal Roof Panels and from Section R905.10.4 you see the
answer is A. The answer is located on Page 441 of the IRC.
IRC
4. Steel roof trusses shall be connected to a load bearing wall with No. ___
screws .
A.
B.
C.
D.
8
10
12
15
IRC
4. Steel roof trusses shall be connected to a load bearing wall with No. ___
screws .
A.
B.
C.
D.
8
10
12
15
Keywords - Steel Roof Trusses, Screws From the index, Chapter 8 is RoofCeiling Construction Section R804 is Steel Roof Framing Section 804.3 is
Roof Construction and from Section R804.3.7 you see the answer is B. The
answer is located on Page 421 of the IRC.
IRC
5. Wood trusses can be cut or notched if approved by a design professional.
A. TRUE
B. FALSE
IRC
5. Wood trusses can be cut or notched if approved by a design professional.
A. TRUE
B. FALSE
Keywords - Wood Trusses, Notched From the index, Chapter 8 is RoofCeiling Construction Section R802 is Wood Roof Framing Section
802.10 is Wood Trusses and from Section R802.10.4 you see the
answer is A. The answer is located on Page 376 of the IRC.
IRC
6. For hydronic piping applications, PEX tubing has a maximum hanger
horizontal spacing of ___ feet .
A.
B.
C.
D.
2
2.67
3
4
IRC
6. For hydronic piping applications, PEX tubing has a maximum hanger
horizontal spacing of ___ feet .
A.
B.
C.
D.
2
2.67
3
4
Keywords - Hydronic Piping, PEX Tubing From the index, Chapter 21 is
Hydronic Piping Section M2101 is Hydronic Piping Systems installation
From Table M2101.9 you see the answer is B. The answer is located on
Page 507 of the IRC.
IRC
7. A gas sauna heater must be equipped with a thermostat that limits room
temperature to ___ degrees Fahrenheit .
A.
B.
C.
D.
100
110
120
194
IRC
7. A gas sauna heater must be equipped with a thermostat that limits room
temperature to ___ degrees Fahrenheit .
A.
B.
C.
D.
100
110
120
194
Keywords - Gas, Sauna From the index, Chapter 24 is Fuel Gas
Section G2440 is Sauna Heaters Section G2440.6 is Heat and Time
Controls from this Section you see the answer is D. The answer is
located on Page 584 of the IRC.
IRC
8. What is the maximum ceiling joist span in feet for #3 Southern Pine (2x6)
with a 16 inch ceiling joist spacing?
A.
B.
C.
D.
18ft 1 in
17ft 8 in
14ft 9 in
18ft 5 in
IRC
8. What is the maximum ceiling joist span in feet for #3 Southern Pine (2x6)
with a 16 inch ceiling joist spacing?
A.
B.
C.
D.
18ft 1 in
17ft 8 in
14ft 9 in
18ft 5 in
Keywords - Ceiling Joist Span, Southern Pine From the index, Chapter 8 is RoofCeiling Construction Section R802 is Wood Roof Framing Section 802.4 is
Allowable Ceiling Joist Spans and from Table R802.4(1) you see the answer is C.
The answer is located on Page 377 of the IRC.
IRC
9. What is the maximum opening in feet for a steel roof?
A.
B.
C.
D.
2
3
4
6
IRC
9. What is the maximum opening in feet for a steel roof?
A.
B.
C.
D.
2
3
4
6
Keywords - Steel Roof, Maximum Opening From the index, Chapter 8 is RoofCeiling Construction Section R804 is Steel Roof Framing Section 804.3 is Steel
Roof Framing and from Section R804.3.6(1) you see the answer is C. The
answer is located on Page 420 of the IRC.
IBC
10. Fire Protection - What is the equivalent opening factor for a 1000 degree
Fahrenheit exposed surface for 1 hour ?
A.
B.
C.
D.
0.1
0.2
0.3
0.5
IBC
10. Fire Protection - What is the equivalent opening factor for a 1000 degree
Fahrenheit exposed surface for 1 hour ?
A.
B.
C.
D.
0.1
0.2
0.3
0.5
Keywords - Fire Protection, Opening Factor This is more of a global question,
think IBC. From the index, Chapter 7 is Fire Resistant Construction Section
705 is Exterior Walls From Section 705.7 you see the answer is B. The
answer is located on Page 97 of the IBC.
IBC
11. The maximum length of any section of exterior structural glass veneer is
___ inches.
A.
B.
C.
D.
24
36
48
60
IBC
11. The maximum length of any section of exterior structural glass veneer is
___ inches.
A.
B.
C.
D.
24
36
48
60
Keywords - Exterior Structural Glass, Length This is more of a global question,
think IBC. From the index, Chapter 14 is Exterior Walls Section 1405 is Installation
of Wall Coverings Section 1405.12 is Glass Veneer and from Section 1405.12.1
you see the answer is C. The answer is located on Page 281 of the IBC.
IBC
12. Roofs and roof covering materials must be compatible with each other .
A. TRUE
B. FALSE
IBC
12. Roofs and roof covering materials must be compatible with each other .
A. TRUE
B. FALSE
Keywords - Roofs, Covering Materials This is more of a global question,
think IBC. From the index, Chapter 15 is Roofing Section 1506 is
Materials From Section 1506.2 you see the answer is A. The answer is
located on Page 289 of the IBC.
IBC
13. Parapet walls should be coped with materials with a minimum width of ___
times the thickness of the wall .
A.
B.
C.
D.
1
1.5
2
2.5
IBC
13. Parapet walls should be coped with materials with a minimum width of ___
times the thickness of the wall .
A.
B.
C.
D.
1
1.5
2
2.5
Keywords - Parapet Walls, Coped This is more of a global question, think
IBC. From the index, Chapter 15 is Roofing Section 1503 is Weather
Protection From Section 1503.3 you see the answer is A. The answer is
located on Page 288 of the IBC.
IBC
14. What is the minimum drip edge overlap (inches) at the eaves and gables of
shingle roofs?
A.
B.
C.
D.
1
2
3
4
IBC
14. What is the minimum drip edge overlap (inches) at the eaves and gables of
shingle roofs?
A.
B.
C.
D.
1
2
3
4
Keywords - Drip Edge, gables, shingle roofs This is more of a global
question, think IBC. From the index, Chapter 15 is Roofing Section 1507
is Requirement for Roof Coverings Section 1507.2 is Asphalt Shingles
and from Section 1507.2.9.3 you see the answer is B. The answer is
located on Page 291 of the IBC.
Interior
Environment
IRC
1. An open vent terminal from a drainage system shall not be located less than
___ fet directly beneath any door.
A.
B.
C.
D.
1
2
3
4
IRC
1. An open vent terminal from a drainage system shall not be located less than
___ feet directly beneath any door.
A.
B.
C.
D.
1
2
3
4
Keywords - Open Vent Terminal, Drainage System From the index, Chapter
31 is Vents Section P3103 is Vent Terminals From Section P3103.5,
Location of Vent Terminal, you see the answer is D. The answer is located
on Page 635 of the IRC.
IRC
2. A 2 inch diameter waste and vent pipe connecting to a horizontal branch or
stack can serve ___ fixture units .
A.
B.
C.
D.
3
4
6
12
IRC
2. A 2 inch diameter waste and vent pipe connecting to a horizontal branch or
stack can serve ___ fixture units .
A.
B.
C.
D.
3
4
6
12
Keywords - Waste and Vent Pipe, Horizontal Branch From the index, Chapter
31 is Vents Section P3111 is Combination Waste and Vent System From
Section P3111.3, Size, you see the answer is A. The answer is located on
Page 638 of the IRC.
IRC
3. Unused openings in any chimney venting system should be closed or
capped.
A. TRUE
B. FALSE
IRC
3. Unused openings in any chimney venting system should be closed or
capped.
A. TRUE
B. FALSE
Keywords - Unused Openings, Venting System From the index, Chapter 18
is Chimneys and Vents Section M1801 is General From Section M1801.10,
you see the answer is A. The answer is located on Page 497 of the IRC.
IRC
4. Relief valves installed on water heaters shall be set to open at least ___ psi
above operating pressure .
A.
B.
C.
D.
25
50
75
100
IRC
4. Relief valves installed on water heaters shall be set to open at least ___ psi
above operating pressure .
A.
B.
C.
D.
25
50
75
100
Keywords - Relief Valves, Water Heaters From the index, Chapter 28 is
Water Heaters Section P2803 is Relief Valves From Section P2803.3,
you see the answer is A. The answer is located on Page 641 of the IRC.
IRC
5. Metal ducts shall be supported by 1/2 inch wide 18-gage metal straps or …
A.
B.
C.
D.
10-gage galvanized wire
12-gage galvanized wire
16-gage galvanized wire
18-gage galvanized wire
IRC
5. Metal ducts shall be supported by 1/2 inch wide 18-gage metal straps or …
A.
B.
C.
D.
10-gage galvanized wire
12-gage galvanized wire
16-gage galvanized wire
18-gage galvanized wire
Keywords - Metal Ducts, Support From the index, Chapter 16 is Duct Systems
Section M1601 is Duct Construction Section 1601.4 is Installation and from Section
M1601.4.3, you see the answer is B. The answer is located on Page 492 of the
IRC.
IRC
6. For PVC hydronic piping, what is the maximum horizontal spacing interval in
feet?
A.
B.
C.
D.
2.67
3
4
6
IRC
6. For PVC hydronic piping, what is the maximum horizontal spacing interval in
feet?
A.
B.
C.
D.
2.67
3
4
6
Keywords - Hydronic Piping, Horizontal Spacing From the index, Chapter 21 is
Hydronic Piping Section M2101 is Hydronic Piping Systems installation From Table
M2101.9 you see the answer is C. The answer is located on Page 505 of the IRC.
IRC
7. Ducts should take return air from inside the dwelling.
A. TRUE
B. FALSE
IRC
7. Ducts should take return air from inside the dwelling.
A. TRUE
B. FALSE
Keywords - Ducts, Return Air From the index, Chapter 16 is Duct Systems
Section M1602 is Return Air From Section M1601.1, you see the answer is A.
The answer is located on Page 491 of the IRC.
IRC
8. Excavations for appliance installation shall extend to a depth
of ___ inches below the appliance .
A.
B.
C.
D.
6
12
16
18
IRC
8. Excavations for appliance installation shall extend to a depth
of ___ inches below the appliance .
A.
B.
C.
D.
6
12
16
18
Keywords - Excavation, Appliance From the index, Chapter 13 is Geneal
mechanical System Requirements Section M1305 is Appliance Access
Section M1305.1.4.2 Excavations, you see the answer is A. The answer
is located on Page 478 of the IRC.
IRC
9. For gas appliances connected by rigid metallic piping, a union must be
installed within ___ feet of the appliance .
A.
B.
C.
D.
2
3
4
6
IRC
9. For gas appliances connected by rigid metallic piping, a union must be
installed within ___ feet of the appliance .
A.
B.
C.
D.
2
3
4
6
Keywords - Gas Appliances, Union From the index, Chapter 24 is Fuel Gas
Section G2422 is Appliance Connections Section G2422.1.4 is Unions from this
Section you see the answer is D. The answer is located on Page 557 of the
IRC.
IBC
10. Cross ventilation must be provided for under floor space .
A. TRUE
B. FALSE
IBC
10. Cross ventilation must be provided for under floor space .
A. TRUE
B. FALSE
Keywords - Cross Ventilation, Under floor space This is more of a global
question, think IBC. From the index, Chapter 12 is Interior Environment
Section 1203 is Ventilation From Section 1203.3 you see the answer is A.
The answer is located on Page 271 of the IBC.
IBC
11. Ventilation openings are not required where mechanical ventilation is
provided continuously at ___ cubic feet per minute .
A.
B.
C.
D.
1
2
3
4
IBC
11. Ventilation openings are not required where mechanical ventilation is
provided continuously at ___ cubic feet per minute .
A.
B.
C.
D.
1
2
3
4
Keywords - Ventilation openings, Mechanical ventilation This is more of a
global question, think IBC. From the index, Chapter 12 is Interior
Environment Section 1203 is Ventilation From Section 1203.3.2 you see the
answer is A. The answer is located on Page 271 of the IBC.
IBC
12. What is the minimum height of a furred ceiling in feet?
A.
B.
C.
D.
7
8
9
10
IBC
12. What is the minimum height of a furred ceiling in feet?
A.
B.
C.
D.
7
8
9
10
Keywords - Minimum Height, Furred Ceiling This is more of a global question,
think IBC. From the index, Chapter 12 is Interior Environment Section 1208 is
Interior Space Dimensions From Section 1208.2.1 Furred Ceiling you see the
answer is A. The answer is located on Page 273 of the IBC.
IBC
13. Interior spaces meant for human occupancy must have a space heating
system capable of maintaining ___ degrees at 3 feet above floor level.
A.
B.
C.
D.
62
65
68
72
IBC
13. Interior spaces meant for human occupancy must have a space heating
system capable of maintaining ___ degrees at 3 feet above floor level.
A.
B.
C.
D.
62
65
68
72
Keywords - Interior Spaces, Space heating This is more of a global question, think
IBC. From the index, Chapter 12 is Interior Environment Section 1204 is
Temperature Control From Section 1204.1 Equipment and Systems you see the
answer is C. The answer is located on Page 272 of the IBC.
IBC
14. Walls, partitions and floor/ceiling assemblies separating dwelling units must
have a sound transmission class of no less than ___ if field tested .
A.
B.
C.
D.
45
50
55
60
IBC
14. Walls, partitions and floor/ceiling assemblies separating dwelling units must
have a sound transmission class of no less than ___ if field tested .
A.
B.
C.
D.
45
50
55
60
Keywords - Separating dwelling units, sound transmission This is more of a
global question, think IBC. From the index, Chapter 12 is Interior Environment
Section 1207 is Sound Transmission From Section 1207.2 Equipment and
Systems you see the answer is A. The answer is located on Page 273 of the
IBC.
Fire protection
mechanical
IRC
1. Sprinklers shall have a temperature rating of not less
than ___ degrees Fahrenheit .
A.
B.
C.
D.
120
135
150
165
IRC
1. Sprinklers shall have a temperature rating of not less
than ___ degrees Fahrenheit .
A.
B.
C.
D.
120
135
150
165
Keywords - Sprinklers, temp rating From the index, Chapter 29 is Water
Supply and Distribution Section P2904 is Fire Sprinkler Systems Section
P2904.2 is Sprinklers, and from Section P2904.2.1 you see the answer is B.
The answer is located on Page 609 of the IRC.
IRC
2. The area of coverage of a single sprinkler shall not exceed ___ feet.
A.
B.
C.
D.
200
300
400
500
IRC
2. The area of coverage of a single sprinkler shall not exceed ___ feet.
A.
B.
C.
D.
200
300
400
500
Keywords - Sprinklers, coverage From the index, Chapter 29 is Water Supply and
Distribution Section P2904 is Fire Sprinkler Systems Section P2904.2 is Sprinklers,
and from Section P2904.2.4.1 you see the answer is C. The answer is located on
Page 610 of the IRC.
IRC
3. Painting of sprinklers is prohibited .
A. TRUE
B. FALSE
IRC
3. Painting of sprinklers is prohibited .
A. TRUE
B. FALSE
Keywords - Sprinklers, painting From the index, Chapter 29 is Water
Supply and Distribution Section P2904 is Fire Sprinkler Systems Section
P2904.2 is Sprinklers, and from Section P2904.2.6 you see the answer is
A. The answer is located on Page 609 of the IRC.
IRC
4. For a one story dwelling unit, the sprinklers must provide the designed flow
rate for ___ minutes .
A.
B.
C.
D.
5
6
7
8
IRC
4. For a one story dwelling unit, the sprinklers must provide the designed flow
rate for ___ minutes .
A.
B.
C.
D.
5
6
7
8
Keywords - Sprinklers, one story From the index, Chapter 29 is Water
Supply and Distribution Section P2904 is Fire Sprinkler Systems Section
P2904.5 is Water Supply, and from Section P2904.5.2 you see the
answer is C. The answer is located on Page 611 of the IRC.
IRC
5. The required flow rate for each sprinkler shall be based on all of the following
except.
A.
B.
C.
D.
Type of room
Area Ceiling
Configuration
Temperature Rating
IRC
5. The required flow rate for each sprinkler shall be based on all of the following
except.
A.
B.
C.
D.
Type of room
Area Ceiling
Configuration
Temperature Rating
Keywords - Sprinklers, flow rate From the index, Chapter 29 is Water Supply
and Distribution Section P2904 is Fire Sprinkler Systems Section P2904.4 is
System Design Flow, and from Section P2904.4.1 you see the answer is A.
The answer is located on Page 611 of the IRC.
IRC
6. CPVC and PEX are nonmetallic piping and tubing listed for use in residential
dwellings sprinklers .
A. TRUE
B. FALSE
IRC
6. CPVC and PEX are nonmetallic piping and tubing listed for use in residential
dwellings sprinklers .
A. TRUE
B. FALSE
Keywords - CPVC, PEX, residential From the index, Chapter 29 is Water
Supply and Distribution Section P2904 is Fire Sprinkler Systems Section
P2904.3 is Sprinkler Piping System, and from Section P2904.3.1 you see the
answer is A. The answer is located on Page 610 of the IRC.
IRC
7. In the available pressure equation, PLm is.
A. Pressure Loss in the water service
pipe
B. Pressure loss in devices
C. Pressure loss in the water meter
D. Pressure loss in elevation
IRC
7. In the available pressure equation, PLm is.
A. Pressure Loss in the water service
pipe
B. Pressure loss in devices
C. Pressure loss in the water meter
D. Pressure loss in elevation
Keywords - Pressure equation From the index, Chapter 29 is Water Supply
and Distribution Section P2904 is Fire Sprinkler Systems Section P2904.6 is
Pipe Sizing, and from Section P2904.6.2.1 you see the answer is C. The
answer is located on Page 611 of the IRC.
IBC
8. An automatic sprinkler system shall be provided in areas containing
woodworking operations exceeding ___ feet .
A.
B.
C.
D.
1,500
2,500
3,000
3,500
IBC
8. An automatic sprinkler system shall be provided in areas containing
woodworking operations exceeding ___ feet .
A.
B.
C.
D.
1,500
2,500
3,000
3,500
Keywords - Sprinkler system, woodworking This is more of a global
question, think IBC. From the index, Chapter 9 is Fire Protection Systems
Section 903 is Automatic Fire Sprinkler Systems Section 903.2 is Where
required, and from Section 903.2.4.1 you see the answer is B. The answer
is located on Page 185 of the IBC.
IBC
9. An automatic sprinkler system shall be provided in a building with a Group M
occupancy exceeding ___ feet .
A.
B.
C.
D.
10,000
11,000
12,000
13,000
IBC
9. An automatic sprinkler system shall be provided in a building with a Group M
occupancy exceeding ___ feet .
A.
B.
C.
D.
10,000
11,000
12,000
13,000
Keywords - Sprinkler system, Group M This is more of a global question,
think IBC. From the index, Chapter 9 is Fire Protection Systems Section
903 is Automatic Fire Sprinkler Systems Section 903.2 is Where required,
and from Section 903.2.7 you see the answer is C. The answer is located
on Page 185 of the IBC.
IBC
10. An automatic sprinkler system must be supplied in a Group A-4 occupancy
when the occupant load exceeds ___ people .
A.
B.
C.
D.
200
300
400
500
IBC
10. An automatic sprinkler system must be supplied in a Group A-4 occupancy
when the occupant load exceeds ___ people .
A.
B.
C.
D.
200
300
400
500
Keywords - Sprinkler system, Group A-4 This is more of a global question,
think IBC. From the index, Chapter 9 is Fire Protection Systems Section
903 is Automatic Fire Sprinkler Systems Section 903.2 is Where required,
and from Section 903.2.1.4 you see the answer is B. The answer is located
on Page 184 of the IBC.
IBC
11. A repair garage smaller than 10,000 square feet must have an automatic
sprinkler system.
A. TRUE
B. FALSE
IBC
11. A repair garage smaller than 10,000 square feet must have an automatic
sprinkler system.
A. TRUE
B. FALSE
Keywords - Sprinkler system, repair garage This is more of a global question,
think IBC. From the index, Chapter 9 is Fire Protection Systems Section 903
is Automatic Fire Sprinkler Systems Section 903.2 is Where required, and
from Section 903.2.9.1 you see the answer is B. The answer is located on
Page 185 of the IBC.
Safety
IBC
15. If the height of construction is 8 feet and the construction is taking place less
than 5 feet from the lot line, construction railings are required.
A. TRUE
B. FALSE
IBC
15. If the height of construction is 8 feet and the construction is taking place less
than 5 feet from the lot line, construction railings are required.
A. TRUE
B. FALSE
Keywords - Safety Related Question From the IBC index, Section Chapter 33
is Safeguards during Construction From Table 3306.1, the Answer is A. The
answer is located on Page 568 of the IBC.
IBC
16. Covered walkways shall have a minimum clear height of ___ feet.
A.
B.
C.
D.
6
7
8
10
IBC
16. Covered walkways shall have a minimum clear height of ___ feet.
A.
B.
C.
D.
6
7
8
10
Keywords - Safety Related Question From the IBC index, Section
Chapter 33 is Safeguards during Construction From Section 3306.7,
the Answer is C. The answer is located on Page 568 of the IBC.
IBC
17. A fire extinguisher must be located in every storage and construction shed.
A. TRUE
B. FALSE
IBC
17. A fire extinguisher must be located in every storage and construction shed.
A. TRUE
B. FALSE
Keywords - Safety Related Question From the IBC index, Section Chapter
33 is Safeguards during Construction From Section 3309.1, the Answer is A.
The answer is located on Page 569 of the IBC.
IBC
18. Construction railings shall be at least ___ inches high.
A.
B.
C.
D.
32
36
42
48
IBC
18. Construction railings shall be at least ___ inches high.
A.
B.
C.
D.
32
36
42
48
Keywords - Safety Related Question From the IBC index, Section
Chapter 33 is Safeguards during Construction From Section 3306.4,
the Answer is C. The answer is located on Page 568 of the IBC.
IBC
19. What is the maximum cut slope for permanent excavations?
A.
B.
C.
D.
1 to 1
2 to 1
3 to 1
4 to 1
IBC
19. What is the maximum cut slope for permanent excavations?
A.
B.
C.
D.
1 to 1
2 to 1
3 to 1
4 to 1
Keywords - Safety Related Question From the IBC index, Section
Chapter 33 is Safeguards during Construction From Section 3304.1.1,
the Answer is B. The answer is located on Page 567 of the IBC.
IBC
20. Sanitary facilities must be provided during construction and remodeling, but
not for demolition.
A. TRUE
B. FALSE
IBC
20. Sanitary facilities must be provided during construction and remodeling, but
not for demolition.
A. TRUE
B. FALSE
Keywords - Safety Related Question From the IBC index, Section Chapter 33 is
Safeguards during Construction From Section 3305.1, the Answer is B. The
answer is located on Page 567 of the IBC.
IBC
21. Construction barriers for excavations less than 5 feet from the lot line must
be at least ___ feet high.
A.
B.
C.
D.
4
5
6
8
IBC
21. Construction barriers for excavations less than 5 feet from the lot line must
be at least ___ feet high.
A.
B.
C.
D.
4
5
6
8
Keywords - Safety Related Question From the IBC index, Section Chapter
33 is Safeguards during Construction From Section 3306.9, the Answer is B.
The answer is located on Page 569 of the IBC.
IBC
22. Stumps and roots must be removed to a depth of ___ inches below the
surface of the ground in the area occupied by the building.
A.
B.
C.
D.
6
12
18
24
IBC
22. Stumps and roots must be removed to a depth of ___ inches below the
surface of the ground in the area occupied by the building.
A.
B.
C.
D.
6
12
18
24
Keywords - Safety Related Question From the IBC index, Section Chapter 33
is Safeguards during Construction From Section 3304.1, the Answer is B. The
answer is located on Page 567 of the IBC.