Project Contributions
Download
Report
Transcript Project Contributions
Tip Shrouding Experimentation
towards Silencing the Open Rotor
Engine
An Undergraduate Senior Project in Aerospace Engineering
Jose M. Rodriguez
Joshua M. Brander
Octavio A. Camarillo
Michael L. Chan
Suk Hyung Lee
David D. Scholtz
May 21st, 2011
Aerospace Engineering Department
California State Polytechnic University-Pomona
Introductions
Joshua Brander
Lucerne Valley, CA
Background & Interests:
Automotive Racing
Model Rocketry
Project Contributions:
Aerodynamics
CAD/Design
Computational Fluid Dynamics
5/21/2011
Jose M. Rodriguez et. al
2
Introductions
Octavio Camarillo
Anaheim, CA
Background & Interests:
Aerodynamics
Structural Dynamics
Project Contributions:
Structural Analysis
5/21/2011
Jose M. Rodriguez et. al
3
Introductions
Michael Chan
Garden Grove, CA
Background & Interests:
CNC Programming/Machining
Manufacturing & QA.
Unmanned Aerial Vehicles
Project Contributions:
Aerodynamic Design
Testing & Manufacturing
Configuration/Integration
5/21/2011
Jose M. Rodriguez et. al
4
Introductions
Suk Hyung Lee
Seoul, Republic of Korea
Background & Interests:
Military Service- Infantry (Korea)
PCB Design & Electronics Mfg
Distinguished Honors Student
Sigma Gamma Tau
Tau Beta Pi
Alpha Gamma Sigma
Golden Key Int’l
Project Contributions:
Rapid Prototype Manufacturing
Finite Element Methods/Structural Analysis
5/21/2011
Jose M. Rodriguez et. al
5
Introductions
David Scholtz
Ontario, CA
Background & Interests:
Logistics/Cargo Planning
Math & Physics Tutoring
Project Contributions:
CAD/Design
Graphics & Modeling
Acoustic Measurement
5/21/2011
Jose M. Rodriguez et. al
6
Introductions
Jose M. Rodriguez
Apple Valley, CA
Background & Interests:
Military Service– U.S. Navy
Aircraft Maintenance
Flight Test/Operations
Air Breathing Engines
Turbomachinery
Project Contributions:
Project Manager
Integration & Testing
Acoustic Measurement
5/21/2011
Jose M. Rodriguez et. al
7
History & Background
Engines Commonly known as :
◦ Open Rotor
◦ “Propfans”
◦ Unducted Fan Engines
Courtesy of NASA GRC
External set of Counter-Rotating blades
◦ Power Turbine-driven
◦ Mechanically (gearbox) driven
5/21/2011
Jose M. Rodriguez et. al
8
History & Background
Two Main Programs:
◦ GE/NASA
◦ UDF GE-36
1970’s-1989
Turbine Driven
◦ Pratt & Whitney-Allison
◦ UHB 578-DX
1986-1990
Gearbox Driven
5/21/2011
Jose M. Rodriguez et. al
9
History & Background
Interest sparked in 1970’s due to rising fuel
prices/Oil Embargos
Promising designs showed a 30%
improvement in Fuel Efficiency
5/21/2011
Jose M. Rodriguez et. al
10
History & Background
Problems & Disadvantages:
◦ Limited Mounting Configurations
◦ High Vibrations imparted onto fuselage
◦ Reduced Cruising Speeds
◦ VERY LOUD!!!!!
In-cabin noise said to be extreme despite aft
mounting on MD-80 series testbed aircraft
A reduction of approx. 30dB was needed to
realize this concept
5/21/2011
Jose M. Rodriguez et. al
11
Why Study?
Interest in Open Rotor Engines is making a
comeback due to increasing fuel/oil prices
and “Green” revolution
◦ GE/NASA Leap-X/CF34
◦ Rolls-Royce RB2011
Pertinent & Interesting
topic for senior project
Multi-faceted study
5/21/2011
Jose M. Rodriguez et. al
12
Our Approach
Attempt to silence by:
◦ Understanding & Manipulating
Blade Tip Vortices
Blade Vortex Interaction (BVI) Noise
Turbulence Ingestion & Broadband Noise
◦ Use of a shroud to reduce BVI & Broadband Noise
Minimize drag
Maximize blade exposure to free stream
Reduce Turbulent Wakefield
5/21/2011
Jose M. Rodriguez et. al
13
Our Approach
Mimic known good/previous work
GE/NASA
(Allison) Rolls-Royce
5/21/2011
Jose M. Rodriguez et. al
14
Tip Shrouding
Typical Fan shrouds encapsulate entire rotor
◦ Drag becomes very unfavorable at high speeds
Tip Shroud:
◦ Leaves over 70% of blade open to free-stream
◦ Geometry creates much less drag than a
conventional shroud
5/21/2011
Jose M. Rodriguez et. al
15
Tip Shrouding
5/21/2011
Jose M. Rodriguez et. al
16
Limitations
Manufacturing/Materials/Cost
◦ Avoid Aerodynamic/Blade re-designs (Time)
Simple Mechanisms
◦ Variable Pitch & control too complex
◦ Basic power/drive method
Static Testing (ground conditions only)
Computing Power
5/21/2011
Jose M. Rodriguez et. al
17
Model Design
Desired to use GE UDF blade configuration
with a variant of NASA SR-7 Blade
◦ 12 Blade Front, 10 Blade Rear
◦ Could not acquire appropriate airfoil data, etc.
Found P&W patent (expired 1996):
◦ Provided airfoil coordinates and data for
aerodynamically-correct modeling.
5/21/2011
Jose M. Rodriguez et. al
18
Design & CAD
David D. Scholtz
5/21/2011
Jose M. Rodriguez et. al
19
Blade Modeling
Based off of UTC Patent # 4,730,985
◦ Provided:
cross-sectional data
coordinates & blade angles
◦ Excel was used to convert 2D
coordinates into 3D and rotate
cross-section by associated
blade angle
Used Solidworks® to model
5/21/2011
Jose M. Rodriguez et. al
20
Considerations in Blade Design
(Fixed-Pitch) Blade angle changed to run
in static conditions
Decreased blade loading was desired
◦ Blade Angle (BA): Angle from Chord Line to
Plane of Rotation
◦ BA was decreased from 75.86o by 41.86o to
decrease b along blade
◦ Root BA = 34.00o; Tip BA = 12.18o
5/21/2011
Jose M. Rodriguez et. al
21
Blade Angle Configuration
5/21/2011
Jose M. Rodriguez et. al
22
Build Considerations of Blades
Increased thickness of to allow scaling and
manufacturability
◦ Each half of airfoil face
increased by .34 in, full scale to
provide a scaled down
thickness of .05 in. at the tip
for model strength.
5/21/2011
Jose M. Rodriguez et. al
23
Rotor Modeling
Rotors were created on SolidWorks, via
Circular Patterning feature.
Front (CW):
◦ 10 blades
◦ 6.50 in. diameter
Rear (CCW):
◦ 8 blades
◦ 5.71 in. diameter
5/21/2011
Jose M. Rodriguez et. al
24
Nacelles for Test Rig
Front and rear nacelles designed to allow
smooth flow across rotors.
5/21/2011
Jose M. Rodriguez et. al
25
Tip Shrouds
Two models designed to experiment with
Model 1:
◦ Basic circular shape, internally flat
Suspected would not be beneficial due to flow separation
along inner wall of an un-cambered surface
5/21/2011
Jose M. Rodriguez et. al
26
Tip Shrouds
Model II:
◦ Created with airfoil cross-section to augment
flow across tip-shroud interface
5/21/2011
Jose M. Rodriguez et. al
27
Computational Fluid Dynamics
Joshua M. Brander
5/21/2011
Jose M. Rodriguez et. al
28
CFD of Counter-Rotating Rotors
•
CD-Adapco STAR-CCM+
•
Desired to Model Front CW and Aft CCW
Rotor Blades simultaneously
•
Counter-Rotating Assemblies have very
complex flows
•
Limited Computing Power Available
•
Modeled Front Assembly only
5/21/2011
Jose M. Rodriguez et. al
29
Turbulence Modeling
Flow Visualization
◦ Trimmer Mesh Model w/ Prism Layer Mesher
◦ 0.02 sec Time Step with 30 Inner Iterations/Step
◦ K-Omega Turbulence Model
Pressure Distribution
◦ Polyhedral Mesh Model with Prism Layer Mesher
◦ Smaller Time Step Required Fine Mesh
5 x 10-6 Time Step w/ 20 Inner Iterations per Step
◦ K-Omega Turbulence Model
5/21/2011
Jose M. Rodriguez et. al
30
Front Rotor
Flow Velocity M = 0.2
(ground operation/take-off conditions)
1000 RPM
Clockwise (CW) Rotation
5/21/2011
Jose M. Rodriguez et. al
31
Pressure Distribution
(Incoming Flow)
5/21/2011
Jose M. Rodriguez et. al
32
Pressure Distribution
(Thrust Side)
5/21/2011
Jose M. Rodriguez et. al
33
Streamline Pattern
@ 0.5 sec or 8 Rotations
5/21/2011
Jose M. Rodriguez et. al
34
Tip Vortex Visualization
5/21/2011
Jose M. Rodriguez et. al
35
Front Rotor w/ Flat Shroud
Flow Velocity M = 0.7
1000 RPM
Streamline @ 0.5 sec or 8 Rotations
5/21/2011
Jose M. Rodriguez et. al
36
Visualization of Secondary Flows &
Separation
Flow Velocity M = 0.2
1000 RPM
Streamline @ 0.5 sec or 8 Rotations
5/21/2011
Jose M. Rodriguez et. al
37
Unfavorable Flow Separation @ Tips
5/21/2011
Jose M. Rodriguez et. al
38
Front Rotor w/ Augmented Shroud
Flow Velocity M = 0.2
(ground operation/take-off conditions)
1000 RPM
Clockwise (CW) Rotation
5/21/2011
Jose M. Rodriguez et. al
39
Pressure Distribution
(Incoming Flow)
5/21/2011
Jose M. Rodriguez et. al
40
Pressure Distribution
(Thrust Side)
5/21/2011
Jose M. Rodriguez et. al
41
Streamline Pattern
@ 0.5 sec or 8 Rotations
5/21/2011
Jose M. Rodriguez et. al
42
Flow Remains Attached
@ Tip-Shroud Interface
5/21/2011
Jose M. Rodriguez et. al
43
Structural Analysis
Octavio A. Camarillo
5/21/2011
Jose M. Rodriguez et. al
44
Front Rotor Blade Loading
Pressure distribution
modeled from CFD
results of full scale model
Load magnitudes are
percentages of full scale
loading
Divided into four areas of
different load intensity
5/21/2011
Jose M. Rodriguez et.al
45
Material Strength
5/21/2011
Jose M. Rodriguez et.al
46
Front Rotor Blade
Pre & Post processing using FEMAP
Analysis using
NEi NASTRAN
Static Analysis
Blade will fail at 73%
of CFD load
Max load of 9.5 psi
5/21/2011
Jose M. Rodriguez et.al
47
Rear Rotor Blade
No CFD simulation Available
Used pressure magnitude of
the front blade’s downwash
Assumed Distribution to be
same as the front blade’s.
Blade will fail at 36% of CFD load
Max Press. of 7.5 psi
5/21/2011
Jose M. Rodriguez et.al
48
Shroud
Shroud deformation
analysis
Interest is in shroud
critical deformation
Clearance must be kept
between blade tips and
shroud at all times
Critical Load at 30 psi
◦ Deflection of 0.144 in
5/21/2011
Jose M. Rodriguez et.al
49
Rapid Prototype/Building
Suk Hyung Lee
5/21/2011
Jose M. Rodriguez et. al
50
Rapid Prototyping
OBJET® Rapid Prototype Machine
◦ Alaris 30 3-D Printer
16μ layering
600 DPI when building along X & Y axis
800 DPI when building up along Z axis*
5/21/2011
Jose M. Rodriguez et. al
51
Materials
5/21/2011
Jose M. Rodriguez et. al
52
Prototyping Software
Object Studio
◦ Source Files
STL files
SLC files
◦ Multiple objects on build
tray
◦ Positioning
◦ Configuring object &tray
parameters
◦ Sending the file to Alaris
3-D printer
5/21/2011
Jose M. Rodriguez et. al
53
Front Rotor Assembly
Manufacturing Time • 226 g Model Material
◦ Warm-up
20 min
◦ Production
11 hr 40 min
◦ TOTAL:
12 hours
• 565 g Support Material
5/21/2011
Jose M. Rodriguez et. al
54
Rear Rotor Assembly
Manufacturing Time
◦ Warm-up
20 min
◦ Production
9 hr 20 min
◦ TOTAL:
9 hr 40 min
• 138 g Model Material
• 319 g Support Material
5/21/2011
Jose M. Rodriguez et. al
55
Manufacturing of Test Rig
Michael L. Chan
5/21/2011
Jose M. Rodriguez et. al
56
NASA Test Rig Inspiration
5/21/2011
Jose M. Rodriguez et. al
57
Test Rig Manufacturing
5/21/2011
Jose M. Rodriguez et. al
58
Dual Pylon Test Stand
5/21/2011
Jose M. Rodriguez et. al
59
Motor L – Bracket
5/21/2011
Jose M. Rodriguez et. al
60
Pylons
5/21/2011
Jose M. Rodriguez et. al
61
Final Assembly
5/21/2011
Jose M. Rodriguez et. al
62
Testing Methods
Jose M. Rodriguez
5/21/2011
Jose M. Rodriguez et. al
63
Compare Noise Fields
Acquire 360° noise characteristics &
observe any noticeable changes
5/21/2011
Jose M. Rodriguez et. al
64
Static Testing
2- 3400kV 14.8 Vdc Electric Motors,
2 Ch. DC Power Supplies
2-Brushless Electronic
Speed Controls
Individually measure RPM
Noise Measurements
Polar Plotsfor both open & shrouded rotors
5/21/2011
Jose M. Rodriguez et. al
65
Work to Follow
Noise Tests & Measurement
◦
◦
◦
◦
Desired: multi-channel microphone arrays
Actual: Blue® Omni-Directional Microphone
Audacity 1.3 Beta Software
PolarPlot v.3.2.7
Study RPM capability & variation
Install Instrumentation on Test Rig
◦ RPM/Tachometers
5/21/2011
Jose M. Rodriguez et. al
66
THANK YOU!!!
Comments
Suggestions
Questions (no hard ones)
Advice
5/21/2011
Jose M. Rodriguez et. al
67