Intro to xDSL Part 1
Download
Report
Transcript Intro to xDSL Part 1
xDSL
Introduction
Yaakov J. Stein
Chief Scientist
RAD Data Communications
Stein Intro xDSL 1.1
PSTN wiring
Stein Intro xDSL 1.2
Old (analog) PSTN
subscriber line
subscriber line
Stein Intro xDSL 1.3
Voice-grade modems
UTP
modem
modem
Stein Intro xDSL 1.4
New (digital) PSTN
CO SWITCH
“last mile”
TDM
analog
digital
PSTN
TDM
“last mile”
CO SWITCH
Stein Intro xDSL 1.5
Voice-grade modems
new PSTN
over
CO SWITCH
PSTN
UTP subscriber line
modem
CO SWITCH
modem
Modem technology is basically unchanged
network/
ISP
Communications speeds do not increase
router
Stein Intro xDSL 1.6
Unshielded Twisted Pair
Stein Intro xDSL 1.7
What is UTP?
Two plastic insulated copper wires
Two directions over single pair
Twisted to reduce crosstalk
Supplies DC power and audio signal
Due to physics attenuation increases with frequency
Stein Intro xDSL 1.8
Why twisted?
from Bell’s 1881 patent
To place the direct and return lines close together.
To twist the direct and return lines around one another so that they
should be absolutely equidistant from the disturbing wires
n
a
V = (a+n) - (b+n)
b
Stein Intro xDSL 1.9
Why twisted? - continued
But even UTP has some cross-talk
George Cambell models UTP crosstalk
(see BSTJ 14(4) Oct 1935)
a
b
Lbc
Cbc
Lad
Cbd
c
d
Cross-talk due to capacitive and/or inductive mismatch
|I2| = Q f V1 where
Q ~ (Cbc-Cbd) or Q~(Lbc-Lad)
Stein Intro xDSL 1.10
Loading coil
What does a loading coil do?
Flattens response in voice band
Attenuates strongly above voice frequencies
loops longer than 18 Kft need loading coils
88 mH every 6kft starting 3kft
Stein Intro xDSL 1.11
Bridge taps
I forgot to mention bridged taps!
Parallel run of unterminated UTP
unused piece left over from old installation
placed for subscriber flexibility
Signal are reflected from end of a BT
A bridged tap can act like a notch filter!
Stein Intro xDSL 1.12
Other problems
Subscriber lines are seldom single runs of cable
US UTP usually comes in 500 ft lengths
Splices must be made
Average line has >20 splices
Splices corrode and add to attenuation
Gauge changes
Binders typically 26 AWG
Change to 24 after 10 Kft
In rural areas change to 19 AWG after that
Stein Intro xDSL 1.13
CSA guidelines
1981 AT&T Carrier Service Area guidelines
No loading coils
Maximum of 9 Kft of 26 gauge (including bridged taps)
Maximum of 12 Kft of 24 gauge (including bridged taps)
Maximum of 2.5 Kft bridged taps
Maximum single bridged tap 2 Kft
Suggested: no more than 2 gauges
In 1991 more than 60% of US lines met CSA requirements
Stein Intro xDSL 1.14
Present US PSTN
UTP only in the last mile (subscriber line)
70% unloaded < 18Kft
15% loaded > 18Kft
15% optical or digital to remote terminal + DA (distribution area)
PIC, 19, 22, 24, 26 gauge
Built for 2W 4 KHz audio bandwidth
DC used for powering
Above 100KHz:
severe attenuation
cross-talk in binder groups (25 - 1000 UTP)
lack of intermanufacturer consistency
Stein Intro xDSL 1.15
xDSL
Stein Intro xDSL 1.16
Alternatives for data services
Fiber, coax, HFC
COST: $10K-$20K / mile
TIME: months to install
T1/E1
COST: >$5K/mile for conditioning
TIME: weeks to install
DSL
COST: @ 0 (just equipment price)
TIME: @ 0 (just setup time)
Stein Intro xDSL 1.17
xDSL
Need higher speed digital connection to subscribers
Not feasible to replace UTP in the last mile
Older voice grade modems assume 4KHz analog line
Newer (V.90) modems assume 64Kbps digital line
DSL modems don’t assume anything
Use whatever the physics of the UTP allows
Stein Intro xDSL 1.18
xDSL System Reference Model
Analog
modem
CO SWITCH
PSTN
POTS-C
network/
ISP
router
POTS
SPLITTER
WAN
POTS-R
UTP
POTS
SPLITTER
DSLAM
xTU-C
PDN
xTU-R
x = H, A, V, ...
Stein Intro xDSL 1.19
Splitter
Splitter separates POTS from DSL signals
Must guarantee lifeline POTS services!
Hence usually passive filter
Must block impulse noise (e.g. ring) from phone into DSL
ADSLforum/T1E1.4 specify that splitter be separate from modem
No interface specification yet (can’t buy splitter and modem from different vendors)
Splitter requires installation
Costly technician visit is the major impediment to deployment
G.lite is splitterless ADSL
Stein Intro xDSL 1.20
Why is DSL better
than a voice-grade modem?
Analog telephony modems are limited to 4 KHz bandwidth
Shannon’s theorem tells us that the maximum transfer rate
for SNR >> 1
N
S
C = BW log2 ( SNR + 1 )
C(bits/Hz) = SNR(dB) / 3
So by using more BW we can get higher transfer rates!
But what is the BW of UTP?
Stein Intro xDSL 1.21
Attenuation vs. frequency
Stein Intro xDSL 1.22
Maximum reach
Length of cable for reliable communications
ASSUMING ONLY THERMAL NOISE
Bellcore study in residential areas (NJ) found
-140 dBm / Hz
white (i.e. independent of frequency)
is a good approximation
Real systems have other sources of noise,
and thus have lower reach (Shannon!)
We can compute the maximum reach from UTP attenuation
Stein Intro xDSL 1.23
xDSL - Maximum Reach
Stein Intro xDSL 1.24
Sources of Interference
XMTR
RCVR
RCVR
XMTR
FEXT
NEXT
RCVR
XMTR
THERMAL
NOISE
XMTR
RCVR
RF INGRESS
Stein Intro xDSL 1.25
Interference for xDSL
Stein Intro xDSL 1.26
Examples of Realistic Reach
More realistic design goals (splices, some xtalk)
1.5 Mbps
18 Kft
5.5 km
(80% US loops)
2 Mbps
16 Kft
5 km
6 Mbps
12 Kft
3.5 km
10 Mbps
7 Kft
13 Mbps 4.5 Kft
1.4 km
26 Mbps
3 Kft
900 m
52 Mbps
1 Kft
300 m (SONET
(CSA 50% US loops)
2 km
STS-1 = 1/3 STM-1)
Stein Intro xDSL 1.27
xDSL flavors
modem
speed
reach
main applications
IDSL
160 (144) Kbps
5.5 km
HDSL
2 Mbps (4-6W)
3.6-4.5 km
HDSL2
2 Mbps (2W)
3 km
POTS
replacement,
videoconferencing,
Internet access
T1/E1 replacement
PBX interconnect,
FR
same as HDSL
SDSL
<= 2 Mbps
3 km
same as HDSL
Stein Intro xDSL 1.28
xDSL flavors
modem
speed
reach
main applications
ADSL
6 Mbps DS
640 Kbps US
3.5-5.5 km
residential Internet,
video-on-demand
ADSL2
8 Mbps DS
800 Kbps US
> ADSL
Internet access,
VoIP
ADSL2+
16 Mbps DS
800 Kbps US
< 2 km
“
VDSL
<= 52 Mbps
300m - 1 km
VDSL2
200 Mbps
(aggregate)
up to 1.8 km
LAN interconnect,
HDTV,
combined services
“
cable modem
10-30Mbps DS
shared
50 km
residential Internet
HPNA
1, 10 Mbps
home wiring
residential
networking
Stein Intro xDSL 1.29
ITU G.99x standards
G.991 HDSL (G.991.1 HDSL
G.992 ADSL (G.992.1 ADSL G.992.2 splitterless ADSL
G.991.2 SHDSL)
G.992.3 ADSL2 G.992.4 splitterless ADSL2
G.992.5 ADSL2+)
G.993 VDSL (G.993.1 VDSL
G.994 HANDSHAKE
G.995 GENERAL (INFO)
G.996 TEST
G.997 PLOAM
G.998 bonding (G.998.1 ATM
G.993.2 VDSL2)
G.998.2 Ethernet G.998.3 TDIM)
Stein Intro xDSL 1.30
Bonding
If we need more BW than attainable by Shannon bounds
we can use more than one UTP pair (although XT may reduce)
this is called bonding or inverse multiplexing
There are many ways of using multiple pairs:
ATM - extension of IMA (may be different rates per pair)
cells marked with SID and sent on any pair
Ethernet - based on 802.3(EFM)
frames are fragmented, marked with SN, and sent on many pairs
Time division inverse mux
Dynamic Spectral Management (Cioffi)
Ethernet link aggregation
Stein Intro xDSL 1.31
xDSL types
Stein Intro xDSL 1.32
T1 service
1963: Coax deployment of T1
2 groups in digital TDM
RZ-AMI line code
Beyond CSA range should use DLC (direct loop carrier)
Repeaters every 6 Kft
Made possible by Bell Labs invention of the transistor
1971: UTP deployment of T1
Bring 1.544 Mbps to customer private lines
Use two UTP in half duplex
Requires expensive line conditioning
One T1 per binder group
Stein Intro xDSL 1.33
T1 line conditioning
In order for a subscriber’s line to carry T1
Single gauge
CSA range
No loading coils
No bridged taps
Repeaters every 6 Kft (starting 3 Kft)
One T1 per binder group
Labor intensive (expensive) process
Need something better … (DSL)
Europeans already found something better
Stein Intro xDSL 1.34
The first xDSL!
1984,88: IDSL
BRI access for ISDN
2B1Q (4 level PAM) modulation
Prevalent in Europe, never really caught on in US
144 Kbps over CSA range
1991: HDSL
Replace T1 line code with IDSL line code (2B1Q)
1 UTP (3 in Europe for E1 rates)
Full CSA distance without line conditioning
Requires DSP
Stein Intro xDSL 1.35
HDSL
Replace T1/E1 DS1 service
Use 2B1Q line code, DFE
Full duplex on each pair with echo cancellation
CSA reach w/o conditioning/repeaters
more complex DSP
ANSI: 2 pairs for T1 (each 784 Kbps)
ETSI: 1, 2, 3 or 4 pairs
Most mature of DSL technologies
Stein Intro xDSL 1.36
HDSL2
Customers request HDSL service that is
single UTP HDSL
at least full CSA reach
spectrally compatible w/
HDSL, T1, ADSL, etc.
Variously called
HDSL2 (ANSI)
SDSL Symmetric DSL (ETSI)
Now called
SHDSL Single pair HDSL (ITU)
Stein Intro xDSL 1.37
ADSL (full rate)
Asymmetric - high rate DS lower rate US
Originally designed for video on demand
Almost retired due to lack of interest
…but then came the Internet
Studies show DS:US should be about 10:1
full rate ADSL 512-640 kbps US, 6-8 Mbps DS G.lite 512 Kbps US, 1.5 Mbps DS
ADSL could mean All Data Subscribers Living
Stein Intro xDSL 1.38
G.lite
Splitterless ADSL, UAWG
ADSL compatible DMT compatible using only 128 tones
512 Kbps US / 1.5 Mbps DS
Still much faster than V.34 or V.90 modems
No splitter required!
Certain features removed for simplicity
simpler implementation (only 500 MIPS < 2000 MIPS for full rate)
Stein Intro xDSL 1.39
ADSL2
ADSL uses BW from 20 kHz to 1.1 MHz
ADSL2 Increases rate/reach of ADSL by using 20 kHz - 4.4 MHz
Also numerous efficiency improvements
better modulation
reduced framing overhead
stronger ECC
reduced power mode
misc. algorithmic improvements
for given rate, reach improved by 200 m
3 user data types - STM, ATM and packet (Ethernet)
ADSL2+ dramatically increased rate at short distances
Stein Intro xDSL 1.40
VDSL
Optical network expanding (getting closer to subscriber)
Optical Network Unit ONU at curb or basement cabinet
FTTC (curb), FTTB (building)
These scenarios usually dictates low power
Rates can be very high since required reach is minimal!
Proposed standard has multiple rates and reaches
Stein Intro xDSL 1.41
VDSL2
VDSL uses BW of 1.1 MHz - 12 MHz (spectrally compatible with ADSL)
VDSL2 uses 20 KHz - 30 MHz
new band-plans
increased DS transmit power
various algorithmic improvements
borrowed improvements from ADSL2
3 user data types - STM, ATM and packet (pure Ethernet)
Stein Intro xDSL 1.42
HPNA (G.PNT)
Studies show that about 50% of US homes have a PC
30% have Internet access, 20% have more than one PC!
Average consumer has trouble with cabling
HomePNA de facto industry standard for home networking
Computers, peripherals interconnect (and connect to Internet?)
using internal phone wiring (user side of splitter)
Does not interrupt lifeline POTS services
Does not require costly or messy LAN wiring of the home
Presently 1 Mbps, soon 10 Mbps, eventually 100 Mbps!
Stein Intro xDSL 1.43
Competition - Cable modems
CABLE
MODEM
CMTS
CATV
HEADEND
fiber
OPTICAL
FIBER
CABLE
coax
COAXIAL
MODEM
AMPLIFIER
NODE
CABLE
MODEM
CABLE
MODEM
Stein Intro xDSL 1.44
Modem Theory
Stein Intro xDSL 1.45
How do modems work?
The simplest attempt is to simply transmit 1 or 0 (volts?)
1
1
1
0
0
1
0
1
This is called NRZ (short serial cables, e.g. RS232)
Information rate = number of bits transmitted per second (bps)
Stein Intro xDSL 1.46
The simplest modem - DC
So what about transmitting -1/+1?
1
1
1
0
0
1
0
1
This is better, but not perfect!
DC isn’t exactly zero
Still can have a long run of +1 OR -1 that will decay
Even without decay, long runs ruin timing recovery (see below)
Stein Intro xDSL 1.47
The simplest modem - DC
What about RZ?
1
1
1
0
0
1
No long +1 runs, so DC decay not important
Still there is DC
Half width pulses means twice bandwidth!
0
1
Stein Intro xDSL 1.48
The simplest modem - DC
T1 uses AMI (Alternate Mark Inversion)
1
1
1
0
0
1
0
1
Absolutely no DC!
No bandwidth increase!
Stein Intro xDSL 1.49
The simplest modem - DC
Even better - use OOK (On Off Keying)
1
1
1
0
0
1
0
1
Absolutely no DC!
Based on sinusoid (“carrier”)
Can hear it (morse code)
Stein Intro xDSL 1.50
PSK
Even better to use sinusoids with different phases!
BPSK
1 bit / symbol
1
1
1
0
0
1
0
1
or QPSK
2 bits / symbol
Bell 212 2W 1200 bps
V.22
11
10
01
01
00
11
01
Stein Intro xDSL 1.51
QAM
Finally, best to use different phases and amplitudes
2 bits per symbol
11
10
01
01
00
11
01
V.22bis 2W full duplex 2400 bps used 16 QAM (4 bits/symbol)
This is getting confusing
Stein Intro xDSL 1.52
Star watching
For QAM we can draw a diagram with
x and y as axes
A is the radius, f the angle
For example, QPSK can be drawn (rotations are time shifts)
Each point represents 2 bits!
Stein Intro xDSL 1.53
QAM constellations
16 QAM
V.29 (4W 9600 bps)
V.22bis 2400 bps
Codex 9600 (V.29)
2W
first non-Bell modem
(Carterphone decision)
Adaptive equalizer
Reduced PAR constellation
Today - 9600 fax!
8PSK
V.27
4W
4800bps
Stein Intro xDSL 1.54
QAM constellations (cont)
Stein Intro xDSL 1.55
DMT - continued
frequency
time
Stein Intro xDSL 1.56
xDSL Line Codes
PAM
IDSL (2B1Q)
HDSL2 (with TCM and optionally OPTIS)
SDSL
QAM/CAP
proprietary HDSL/ADSL/VDSL
DMT
ADSL
G.lite
VDSL line code war is still raging
Stein Intro xDSL 1.57
Duplexing
How do we send information in BOTH directions?
Earliest modems used two UTP, one for each direction (4W)
Next generation used 1/2 bandwidth for each direction (FDD)
Alternative is to use 1/2 the time (TDD)
More advanced DSP uses adaptive echo canceling
modulator
4W to 2W
LEC
UTP
HYBRID
demodulator
Stein Intro xDSL 1.58
ADSL FDD Duplexing
US uses tones 8 - 32 (below 30 KHz reserved)
DS uses 256 tones (FDM from tone 33, EC from tone 8)
P
O
T
S
US
8
DS
32
256
Stein Intro xDSL 1.59