Transcript PROGRESS of BRAKING REGULATION 13.

PROGRESS of BRAKING REGULATION 13.
PROGRESS of BRAKING REGULATION 13.
09 Amendments Oct 1996.
Annex 2 Data increase. Vehicle mass when tested + Type III test for trailer - Test Results
Annex 4 -
1.5.2.1.
1.6.1/2.
1.6.3.
1.7.
2.1.2.
2.3.6.
Fade test for small trailers - continuous braking.
Type II 6% downhill test - M3,N3 with in-gear or retarder use.
Hot performance test 3.75 m/s2 for M3 3.3 m/s2 N3
Type III fade test for O4 - braking snub cycles
Service braking un-braked trailer - 5.4 m/s2 for M1
Dynamic parking brake - 1.5 m/s2 from 30 km/h
Annex 5 -Type IIa test: Endurance braking - 7% grade 6 km/h @ 30km/h
Engine braking alone - 0.6 m/s2
Annex 11
Power driven vehicles and trailers - similar to a reference vehicle already approved.
Using the reference vehicle and known parts, it is permitted to predict braking performance
Annex 12
Trailers with overrun braking - overload protection requirement.
Annex 13
4.3.
5.1.1.2.
6.1.3.
Annex 15
ABS failure performance requirements
Energy consumed by indirectly controlled wheels - taken into account.
Directly controlled wheels must remain under control.
Trailer ABS energy consumption - 15 s operation on stored energy.
Dynamometer test of replacement brake linings
Dyno capacity sufficient to meet Annex 4 Types I, II and III tests and Type III test added.
PROGRESS of BRAKING REGULATION 13.
Supplement 1 - Jan 1997
Main body of the Regulation.
Electric Vehicles -
Category A: Independent braking system
Category B: Part of the Service braking system.
Annex 4
Tests with Electric Vehicles. 1.2.8.
1.2.9
1.5.1.6
1.5.3.1.2
1.5.3.3
2.2.6
If wheel motors permanently connected, test like this.
and make a Type O test on low mu as behaviour test.
Possible to reduce heating cycle speed.
Cat A vehicles shall not use any separate control.
Hot test at max. speed.
Performance tests under faulty RGB conditions.
Annex 8
Release of spring brakes - only when stored pressure allows service brakes to give secondary.
Trailers must provide energy for 3 releases after uncoupling.
Annex 10
3.1.4.5.
EV distribution under all states-of-charge provided unless equipped with ABS.
3.1.5.1/6.1 Distribution of braking with trailers. 4.1.1. 5.1.3. 5.2.1.
Annex 13
Full cycling of ABS during tests.
PROGRESS of BRAKING REGULATION 13
Supplement 2 Jan 1997
REQUIREMENTS for EBS
Definition of new terms:
Control / Energy transmission.
Data Communication.
Coupling Force Control.
Nominal Values.
Connections to trailers
Electric and pneumatic control lines ISO 11992 Standard specified.
Control Line Failures
Electric control line only - not yet permitted.
Incompatible combinations.
Faults in the lines.
Trailer Parking braking signalling Via pneumatic and/or electrical control line.
Compensation
Across axle compensation, axle compensation and
whole vehicle compensation.
Coupling Force Control
On the towing vehicle only
Braking adjustments on both electric and pneumatic control lines
Fault Warning Signals
Two categories: Red and Yellow warnings.
Requirements for Trailers
Similar to those of the towing vehicle but fault signalling different.
Automatic braking.
Annex 2
Annex 4
Annex 6
Vehicle data to be provided for Reg.90 Lining Approvals
3.1.2.2.
O2 and O3 Trailer supply line 7 bar max. Pneumatic control line 0 - 6.5 bar.
Response tests.
Simulators for towing vehicle and trailers - electric line added.
Annex 8
Annex 10
Motor vehicle warning when spring brakes start to be applied.
Diagrams apply to both pneumatic and electrical signals, but curves need not be identical
Annex 13
Trailer performance with ABS failure to be 80% of normal laden figure.
Separate trailer warning signal retained. Supply line at 8 bar at start of consumption tests.
PROGRESS of BRAKING REGULATION 13
Supplement 3 - April 98
Regulation 13 and Regulation 13-H made equally valid for Category M1 vehicles.
2.14.
Endurance Braking definitions.
Annex 2
Endurance braking performance reports added.
Annex 4
1.6.4.
1.8.2.
Annex 5
Type IIa test replaces Type II for endurance braking systems on:
Long distance coaches M3
N3 vehicles to tow O4 trailers
ADR vehicles
Type IIa tests on endurance/engine braking
Now deals only with the braking requirements of ADR vehicles.
Supplement 4 Feb 99.
5.1.4.
5.2.1.2.5.
Annex 10
Provisions for Periodic Technical Inspection.
5.1.4.
Inspection access.
5.1.4.2.
Pneumatic pressure test connections
5.1.4.5.
Pneumatic data provided
Common components allowed in Service and Parking braking systems.
3.1.1.
3.1.4.2.
Simultaneous lock-up accepted on 4WD vehicles.
Permanent 4WD vehicles - wheel locking sequence tests.
PROGRESS of BRAKING REGULATION 13
Supplement 5 Dec 2000
Revision of EBS rules. ISO 11992 - 1/2/3 updated to 1998 release.
Pneumatic and electric control line agreement.
ISO 11992 compatibility on towing vehicles and trailers (Annex 17 tests)
Single transmission energy reserve if secondary reached by muscular energy
Trailer only braking allowed for stability control.
EPB rules revised (now very complicated)
EBS has to generate 5.8 m/s2 even with ignition off.
Single temporary transmission failure - no distinguishable effect.
No discharge of battery when all normal electrical loads on and engine running
Warning signals revised somewhat.
Other failures may use flashing brake warnings but only when stationary.
Alternative to Automatic braking on electric only signalling.
Simulator performance explained
Annex 15
Dynamometer cooling air speed increased.
Annex 16
Interpretation of ISO 11992 applications ( brakes and running gear.)
Annex 17
ISO 11992 compatibility test procedure using simulators defined.
PROGRESS of BRAKING REGULATION 13
Supplement 6 Jan 2002
Electric Vehicles replaced with ‘Vehicles with Electrical Regenerative Braking’
Rules and tests to be applied:
Phased Braking
Compensation for RGB variation
Electric State of Charge.
Electrically Actuated Service Brakes
Over-run Braking Systems:
Additions for overload protection
NEW ANNEX 18:
Requirements for Complex Electronic Vehicle Control Systems.
Definitions - Safety Concept, Systems Units & Boundaries
Documentation - 2 parts
Functional description
System layout and interconnections
Safety concept
Verification and Test
New Regulation Issues to be Considered.
Final WP29 acceptance of Modular Trailer Braking System rules.
Global Harmonisation of rules for illuminating Stop Lamps.
PTI requirements connected with brake inspection.
Brake Lining Assemblies - Marking and Packaging.
Towing Vehicle/Trailer Compatibility. (Disc brakes and EBS/CFC)
Reg.90 Test procedures. Dyno tests and speed sensitivity tests.
Longer Term Issues.
Global Harmonisation.
Motor Cycle Braking
Safety Glass, Washers and wipers
Headlamps
Braking. (EVs priority)
Tyres
Seat Belts
Controls and Warning signals.
Anti-theft Devices
Higher Level Automatic Control Systems. (Driver assistance systems - Government concern)
Intelligent Transport Systems. (Industry/Government collaboration?)
Electrical Energy Management Systems.