Transcript Water Hydraulic Valves

Introducing our range of
Water Hydraulic Valves
•
For control of Main Inlet Valve
Servo motor, service & maintenance seals
•
•
•
Pressures up to 120 bar
Flow rates up to 600 litres/min
316L Stainless Steel Construction
Water Hydraulic Control Valves
The 6mm Water Hydraulic Control valve is a ball seated
type valve. The stainless steel / ceramic ball seat design
ensures a virtual leak tight shut off.
•
•
•
•
M.T.B.F., SFF, PFD and SIL Data (Available upon
request)
Easy Installation, Repair and Replacement
Stainless Steel Construction
Up to 120 bar Operating Pressure Range
General Description
The DN6 valve design incorporates a balanced internal piloting system and a lever mechanism to enable a
wide range of operators to operate the valve.
All valves have an ‘O’ Ring interface that enables them to be fitted with BSP.P ported subplates as standard, or
manifold mounted to reduce pipework, fittings, weight and space. This interface also allows direct mounting
of the valve to larger pilot operated valves up to the DN25, increasing the flow capacity to 200 l/min.
By removing just 4 bolts the valves can be dismounted without disturbing pipework and possibly
contaminating the hydraulic system. Blanking and flushing plates can also be supplied.
Water Hydraulic Control Valves
Construction Materials
bodies and subplates: 316L Stainless Steel
• Valve
parts: Various grades of Stainless
• Wetted
Steel/Super Duplex / Ceramic/Aluminium Bronze
Nitrile / Buna N / PTFE / Polyurethane
• Seal
A4, grade 80 stainless steel
• Fasteners:
Springs:
stainless
steel
•
Operating Temperature Range
• Standard: 5 ºC to + 60 ºC
Ingress Protection (solenoids valves )
• IP54
Operating Pressure Range
• 15 to 120 bar
Operating Medium
• Filtered Fresh Water
Recommended Filtration
10 microns
• DN6:
• DN15: 25 microns
25 microns
• DN25:
DN40:
200
microns
•
Water Hydraulic Control Valves
Hydraulic Pilot Operated
• 2 port, 2 position
2 position
• 315port,
to
120
bar pressure range
•
• Flow rates up to 20 l/min
Steel construction
• Stainless
Pilot
media,
Oil or Water
•
Plunger or Roller Cam Operated
• 2 port, 2 position
2 position
• 315port,
to 120 bar pressure range
•
Flow
rates up to 20 l/min
•
Stainless
Steel construction
•
Solenoid Operated with Hydraulic Override Pilot
• 2 port, 2 position
port, 2 position
• 3120
bar max. pressure
•
Flow
rates up to 20 l/min
•
Stainless
Steel construction
• 24VDC, 110VDC,
220VDC
•
• Override signal, oil or water
Water Hydraulic Control Valves
Solenoid Operated
• 3 port, 2 position
rates up to 20 l/min
• Flow
15
to
120 bar working pressure
•
Stainless
Steel construction
•
DN15 & DN25
• Solenoid operated
or Water pilot operated
• Oil
3
port,
2 position
•
• 4 port, 2 position
range 15 to 120 bar
• Pressure
Flow
rates
up to 200 l/min
•
Stainless
Steel
construction
•
media, Oil or Water
• Pilot
Easily
replaceable one piece cartridge
•
valve design
DN40 - Hydraulic Pilot Operated
• 3 port, 2 position
port, 2 position
• 5Pressure
range 15 to 120 bar
•
Flow
rate
up to 600 l/min
•
Stainless
Steel
• Pilot media, Oilconstruction
or Water
•
• Remote position sensors
½ “ SAE 3000 psi Flanged
• 1connections
or BSP.P
threaded ports
before bleed function
• Block
Operating
temperature range
•
5 ºC to + 60 ºC
Water Hydraulic Control Valves
Keep it simple !
Water Hydraulic Control Valves can simplify hydraulic control circuits and therefore
increase reliability, while reducing maintenance and capital costs.
Water Hydraulic Control Valves can replace conventional oil hydraulic power units
and oil servo valves by utilizing the valuable natural renewable energy resource of
water.