Transcript 工作站連線講義
如何連上工作站
WorkStations:
1. Solaris
2. Linux
Use X-Win32 (for Solaris)
WorkStations IP:
140.113.146.23~38
1
預設帳號密碼
帳號:u+學號
密碼:cevlsi
PS:
1.以前有申請過電控工作站帳號的,密碼為
之前申請時使用的密碼。
2.更改密碼的指令為passwd。
2
X-win32 (1)
Select X-Config
Select Add
3
X-win32 (2)
Select XDMCP
Select Next
Enter Session name
Free
Host Name
140.113.146.23~40
29,31,34,35 unable
Switch to Single
Show Message
4
X-win32 (3)
Press the left bottom and Choose ECE
Enter your ID and your password
5
Workstation(1)
Press right bottom
Choose Tools
ChooseTerminal
6
Workstation(2)
Terminal
7
工作站Cadence設定和製程檔載入方法(限修課同學)
"
"
"
"
"
"
"
直接在工作站terminal介面上鍵入括號內指令
cp -r /usr2/ce21/student/u97/u9712525/Cadence . "
製程檔和驗證檔都在此資料夾內
建議將檔案移出至根目錄 或是再次鍵入以下指令(分別載入)
cp /usr2/ce21/student/u97/u9712525/.tcshrc . "
cp /usr2/ce21/student/u97/u9712525/display.drf . "
cp /usr2/ce21/student/u97/u9712525/035ms.tf . "
cp /usr2/ce21/student/u97/u9712525/mm0355v.l . "
cp /usr2/ce21/student/u97/u9712525/calibre.cshrc . "
cp /usr2/ce21/student/u97/u9712525/.cdsinit . "
鍵入 source .tcshrc (之後重新連結就不用再輸入)
每次登入後再鍵入”icfb &”可執行Cadence
8
Terminal常用指令
Set password
passwd
Print working directory
pwd
list the folders and files
ls
Change a directory
cd ~ ; cd ..
Make a directory
mkdir
Remove a empty directory
rmdir
9
EX:鍵入ls,即可列出目前所在資料夾內所有檔案。
10
只要完成以上步驟,就可進行作業
以下新增使用putty軟體連上工作站,
使用putty或xwin32連工作站兩種方式
請擇一即可。
11
1.IP範圍與講義第一頁的設定相同,PORT請選22,PROTOCOL請選SSH
2.下方可讓你儲存目前的連線設定並自行命名,這樣下次要再開就不用重打。
12
回傳畫面方法一:
1. 勾選 Enable X11 forwarding
2. X display location 輸入自己的 IP
13
回傳畫面方法二:
1. 用Putty連線進入工作站後 (請輸入 帳號:u+學號 與 密碼: cevlsi)
2. 輸入 setenv DISPLAY yourIP:0
14
1. 接著請打開xWin32 or Xmanager,將他開啟於常駐程式中。
2. Xmanager請用Passive開啟
15
1.接下來的畫面與在工作站上使用terminal一樣,請依照第8頁的流程使用。
2.再鍵入source calibre.cshrc 與 icfb & 即可開啟cadence。
16
就可以開始劃LAYOUT
17