Transcript Lecture9.1 Building a FET.ppt

Lecture 9.1
Building a FET
Integrated Circuits

CPU or Memory
– First Layer
•
•
•
•
Transistors
Capacitors
Diode
Resistors
– Multi-layer
• Wiring
– Interconnects
– Bonding Pads
• Dielectric
• Capacitors
• Heterostructures
MOSFET in Memory Chip
Source
Gate
Drain
Field Effect Transistor (FET)
Voltage Controlled Resistor
Make Mask for Doping


Clean wafer surface
Oxidize Si Surface
– How Thick is needed for Doping Mask?



Spin on photoresist
Image photoresist
Develop photoresist
– Dissolve un-crosslinked photoresist



Etch exposed SiO2 down to the Si of the wafer
Doping
Remove Implantation Mask
Silicon Oxidation

Reactor
– Furnace at T=850C
– Pure Oxygen
• Si + O2  SiO2

Kinetics
– BL-Mass Transfer
• J=Kg(CA-0)
– SS-Diffusion
• J=DO-SiO2 (dC/dx)
– Heat Transfer
• BL, q=h(T1-T)
• Solid, q=kSiO2(dT/dx)
– J=q/Hrxn
Grxn<0, Spontaneous
Kinetics

Thickness
– Linear Rate
• Reaction Control
– First Order
• BL-MT Control
• BL-HT Control
– Parabolic Rate
• Product diffusion Control
• Product heat transfer Control

J =(dx/dt) SiO2/MW SiO2
Thickness Experiments

Parabolic Rate
– Derive it!
– dx2/dt=2K
• K=Ko exp(-Ea/RgT)
• x=o @ t=0
• x=  at t= 
– Very common!!
• Slow Solid State
Diffusion
• Slow Heat
Conduction
Mask Thickness





To effectively prevent ions penetrating in
thick zone
Relatively thick Oxide Protection layer
Patterned
Thinning (etching) of Oxide Protection
layer over implantation zone
Remove oxide layer with impurities inside
Mask Thickness

Transmission through mask
– T=1/2 erfc[(x-xave)/2 x]
To stop 99.99% of implanted
materials, T=10-4
 Solve for x, the thickness to stop
99.99% of ions.

SiO2 Mask Thickness
Si3N4 Mask Thickness
Photoresist Mask Thickness
Implantation

Create Ions in
Vacuum
 Accelerate in
Electric Field
 Impinge onto
Silicon Surface
 Knock out Si ion(s)
– Charge Balance

Travel deep into
Silicon
Implantation

Effect of Ion Mass
Implant Depth
Depth Increases with Energy
Implantation Straggle
Increases with Energy
Implantation Concentration
Profile

Probability Based
 N(x)=Nmax exp[(x-xave)2/2x2]
Nmax=(Ndose/[(2) x])~(0.4 Ndose/ x)
 Ndose=Qdose/e
 Qdose= current applied/cm2
 σx = projected straggle

Remove Implantation Mask

Chemical Mechanical Polishing
– Remove all Oxide from wafer surface

Dry Etching
Drive Dopant Impurities into Wafer
Heat Treating
 Laser Annealing


Diffusion
– Heat and Hold for period of time
• Solid State Diffusion
• dC/dt=D d2C/dx2
– C=Co at x=0
– C=0 at x=
Concentration Profile
1
C xi  1 hr 
C xi  2 hr 
C xi  3 hr 
time
0.5
C xi  4 hr 
0
0
0.5
xi
m
1
Diffusion of Implanted Dopants

Diffusion Furnace or Laser
 Heat Treatment
– Solid State Diffusion
– dCA/dt = CT d/dz (DAB dXA /dz)
• C=Co(z) = CT XA(z) at z=0
• C=0 at z=
– DAB =(D*A XB + D*B XA) (d ln [aA]/d ln [XA])
– Interdiffusion or mutual diffusion coefficient
Gate Oxide
Capacitor connecting Gate to center
of npn or pnp heterojunction
 Capacitance

– Area
– Thickness
– Dielectric constant of oxide
Field Effect Transistor (FET)
Gate Oxide Capacitance
C=oA/d
=C/Co
=1+e
e =
electric
susceptibility
Field Effect Transistor (FET)
Thickness Experiments

Parabolic Rate
– Derive it!
– dx2/dt=2K
• K=Ko exp(-Ea/RgT)
• x=o @ t=0
• x=  at t= 
– Very common!!
• Slow Solid State
Diffusion
• Slow Heat
Conduction
Metalization

Transistor Contacts
– Base
– Emitter
– Gate
Planarize/Polish layer to get Flat
Surface for next lithography Step
 Metal Deposition
