Section 6.2 - Thermal Design

Download Report

Transcript Section 6.2 - Thermal Design

GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
GLAST Large Area Telescope
Gamma-ray Large
Area Space
Telescope
Calorimeter Subsystem
6.2 Thermal Design and Analysis
Pierre Prat
L.L.R. Ecole Polytechnique
Calorimeter IN2P3 System Engineer
[email protected]
33–1–69–33–39–25
P. Prat
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Design

CAL Thermal Design is Passive
– Primary Mode of Heat Transfer from the AFEE Card is
Conduction Through the CAL Base Plate to the LAT Grid
– Secondary Mode of Heat Transfer from the AFEE Card is
Radiation from the CAL Side Panels to the LAT Grid Walls
– No Dedicated Radiator
– No Survival Heaters
P. Prat
6.2-2
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Design Drivers

Design Drivers –
– A Total of 4 W Maximum is Dissipated from the CAL
Electronics (1 W per AFEE Card) – Defined by AFEE Card
Thermal Analysis
– Majority of TEM Power Dissipated to the X-LAT Plate by
Thermal Straps.
– Survival Temperature Requirement Driven by Dual Pin
Photodiodes
– Survival Limit Cannot be Exceeded in Test
P. Prat
6.2-3
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis – Tasks

Detailed Model of CAL Module
– Construction of the Detailed Model Reflecting Actual Design
– The Detailed Model Parameters Will Be Updated According to
the Thermal Balance Test Measurements on the Engineering
Module (In Particular, Contact Thermal Resistances Will Be
Refined)

Detailed Model of AFEE Card – Presented in Section 7.0

Simplified Model of CAL Module
– Correlation of Results With Detailed Model
– Delivered to SLAC
P. Prat
6.2-4
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis – Methodology

Static Analysis
– Adjustment of the Conductances of the Simplified Model to
Correlate the Results with the Detailed Model for the Hot
and Cold Environment Cases

Transient Analysis
– 10°C Temperature Step Applied on the Grid: Verification of
the Correlation Between the Simplified and the Detailed
Model
P. Prat
6.2-5
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis – Design Limit Loads
CASE
P. Prat
THERMAL LOADS
MIN
MAX
(deg C)
(deg C)
OPERATING TEMPERATURE
-15
+25
SURVIVAL TEMPERATURE
-30
+50
ACCEPTANCE TEMPERATURE
-20
+40
QUALIFICATION TEMPERATURE
-30
+50
6.2-6
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis – Assumptions

Thermal Environment Design Parameters
Temperature (°C)
Emissivity
Tracker
18.5
0.04
Hot case
Grid
18
0.75
TEM
34
0.04
Temperature (°C)
Emissivity
Tracker
-17
0.04
Cold case
Grid
-15
0.9
TEM
-11
0.04
Conductances
(W/K)
Conductive coupling

Grid/base plate conductance (for each side: 4 sides)
2.67
TEM/base plate conductance (for each fixture: 4 fixtures)
0.03
Optical Properties
– 6 CAL Aluminum Faces:
– Alodine 1200 Emissivity = 0.1
P. Prat
6.2-7
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis – Assumptions

Material Properties
Composite (T300 1K PW/M76 ;40% ; 124AW)
Aluminium 2618A
Aluminium 5754
CsI (Tl)
Polyimide
Copper
AFEE PCB (Polyimide + Copper)
Ti 6Al 4V

Conductivity
W/(m.K)
5
146
132
1.1
0.3
385
8.72
7
Specific heat
J/(kg.K)
1.1
0.92
0.945
0.201
1
1
-
Contact conductivities
Materials
Aluminium / Aluminium
Aluminium / Composite (T300 1K PW/M76 ;40% ; 124AW)
Aluminium / Titanium (Ti 6Al 4V)
P. Prat
Density
g/m3
2.76
2.67
4.51
1.16
1.16
-
6.2-8
Contact
conductivity
W/(cm2.K)
0.1650
0.0109
0.0151
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Model Description
– No Geometric Model
– Math Model (Not SINDA): Electrical Analogical Model Using the
Orcad Pspice Simulation Software:
–
–
–
–
–
Voltage (Volt)  Temperature T (°C)
Current (Ampere)  Power P (W)
Electrical Resistance (Ohm)  Thermal Resistance (°C/W)
Electrical Capacitance (µF)  Thermal Capacitance Cth (J/°C)
Time (µS)  Time T (S)
– Simplified Thermal Model Simulation
– Consists of 15 Nodes
– Used for the Detailed LAT Thermal Model Simulation
– Detailed Thermal Model Simulation
– Consists of 3150 Nodes
– Objectives:
» Temperature Static Analysis in the Hot and Cold Cases
» Temperature Transient Analysis: Determination of the Built-up Time
(CsI(Tl) Logs, Aluminum Plates, AFEE Boards)
» Determine the Parameters Which Was Used for the Simplified
Thermal Model
P. Prat
6.2-9
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Simplified Thermal Model

The Simplified Thermal Model Simulation Is Defined in the Document,
LAT-TD-01163-03 (“CAL Simplified Simulation Thermal Model
Definition”)

The CAL Consists of 15 Nodes As Follows:
– 5 Nodes on the Aluminum Base-Plate
– 1 Node on Each AFEE Board
– 1 Node on Each Aluminum Side-Panel/Close-Out Plate Assembly
(Considered Each as a Single Plate)
– 1 Node on the Center of the Composite Structure
– 1 Node on the Top of the Composite Structure

Parameters:
– Thermal Conductances Between Nodes (26)
– Thermal Capacitances at Each Nodes (15)
– Power Sources at Each AFEE Nodes (4)
– Thermal Radiation Parameters (Surface , Emissivity) on Each
External Sides Nodes (6)
P. Prat
6.2-10
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Simplified Thermal Model
P. Prat
6.2-11
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Detailed Thermal Model
 The Complete Simulation Thermal Model is Defined in the Document,
GLAST-LLR-TN-054 (“Detailed Simulation Thermal Model Definition of
a CAL Module”)
 The CAL Model Consists of the Following Sub-Modules
– Base Plate: Modeled by a Plate of 5 X 5 Nodes
– 4 Close-Out Plates/Side Panels: Modeled as a Plate of 7 X 6 Nodes
– 4 AFEE Boards: Modeled as a Plate of 7 X 6 Nodes
– Top Frame: Modeled as a Frame of 16 Nodes
– Composite Structure With CDEs : Modeled by a Network of 2770
nodes
 Radiative and Conductive Interfaces are Modeled with:
– LAT Grid (Radiative/Conductive)
– Tracker (Radiative)
– TEM (Radiative/Conductive)
P. Prat
6.2-12
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Detailed Thermal Model
R L 1 - 1
R L 2 - 1
R L 3 - 1
R L 4 - 1
R L 5 - 1
R L 6 - 1
R L 7 - 1
R L 8 - 1
R L 9 - 1
R L 1 0 - 1
R L 1 1 - 1
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
R L 1 - 3
R L 2 - 3
R L 3 - 3
R L 4 - 3
R L 5 - 3
R L 6 - 3
R L 7 - 3
R L 8 - 3
R L 9 - 3
R L 1 0 - 3
R L 1 1 - 3
{ R lo n g }
N 1 - 1
N 1 - 3
{ R lo n g }
N 2 - 1
N 2 - 3
{ R lo n g }
N 4 - 1
N 4 - 3
{ R lo n g }
N 5 - 1
N 5 - 3
{ R lo n g }
N 6 - 1
N 6 - 3
{ R lo n g }
N 7 - 1
N 7 - 3
{ R lo n g }
N 8 - 1
N 8 - 3
{ R lo n g }
N 9 - 1
N 9 - 3
{ R lo n g }
N 1 0 - 1
N 1 0 - 3
{ R lo n g }
R L 1 2 - 3
{ R lo n g }
N 1 1 - 1
N 1 1 - 3
{ R lo n g }
N 1 2 - 1
N 1 2 - 3
R 2 - H
R 3 - H
R 4 - H
R 5 - H
R 6 - H
R 7 - H
R 8 - H
R 9 - H
R 1 0 - H
R 1 1 - H
R 1 2 - H
{ 2 * R h }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
{ Rh }
R 1 - 3
{ 2 * R e }
R 2 - 1
{ Re }
R 1 - C
R 2 - 3
{ Re }
R 1 - D
{ 2 * R v }
C 2
{ Ct h }
R 2 - D
{ Rv }
0
R 1 - B
R 3 - 3
{ Re }
R 2 - 2
{ Re }
{ 2 * R h }
R 2 - B
C 3
{ Ct h }
R 3 - D
{ Rv }
R 3 - B
R 5 - 3
{ Re }
C 4
{ Ct h }
R 4 - D
{ Rv }
R 4 - 2
{ Re }
R 6 - 3
{ Re }
C 5
{ Ct h }
R 5 - D
{ Rv }
R 4 - B
R 5 - 2
{ Re }
{ Rh }
R 5 - B
R 7 - 1
{ Re }
R 7 - 3
{ Re }
C 6
{ Ct h }
R 6 - D
{ Rv }
{ Rv }
R 6 - 4
{ Re }
R 7 - 2
{ Re }
R 6 - 2
{ Re }
R 8 - 3
{ Re }
R 7 - D
{ Rv }
R 6 - B
N 6 - 2
N 7 - 2
R 7 - B
R 9 - 3
{ Re }
C 8
{ Ct h }
R 8 - D
{ Rv }
R 8 - 2
{ Re }
R 8 - B
N 8 - 2
R 1 0 - 1
{ Re }
R 1 0 - 3
{ Re }
R 9 - D
{ Rv }
C 9
{ Ct h }
R 9 - 2
{ Re }
R 9 - B
N 9 - 2
R 1 0 - D
{ Rv }
C 1 0
{ Ct h }
R 1 0 - 2
{ Re }
{ Re }
R 1 1 - 3
{ Re }
R 1 1 - D
{ Rv }
C 1 1
{ Ct h }
R 1 2 - G
{ Rv }
0
R 1 1 - 2
{ Re }
R 1 0 - B
{ Rh }
N 1 0 - 2
N 9 - 4
R 1 2 - 1
R 1 1 - C{ Re }
R 1 1 - B
R 1 2 - 2
{ Re }
{ Rh }
R 1 3 - G
{ 2 * R v }
R 1 2 - B
R 1 3 - 2
{ 2 * R e }
{ Re }
{ Rh }
R L 2 - 2
R L 3 - 2
R L 4 - 2
R L 5 - 2
R L 6 - 2
R L 7 - 2
R L 8 - 2
R L 9 - 2
R L 1 0 - 2
R L 1 1 - 2
R L 1 2 - 2
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
R L 1 - 4
R L 2 - 4
R L 3 - 4
R L 4 - 4
R L 5 - 4
R L 6 - 4
R L 7 - 4
R L 8 - 4
R L 9 - 4
R L 1 0 - 4
R L 1 1 - 4
R L 1 2 - 4
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
{ R lo n g }
Composite CELL/CDE model diagram
R3
R4
R5
R6
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
PCB1
PCB2
PCB3
PCB4
PCB5
PCB6
PCB7
R14
{RLpcb2*2}
R15
{RLpcb2}
I30
R16
{RLpcb2}
+ -
R25
{RHpcb}
PCB9
R17
{RLpcb2}
I38
+ -
R21
{RHpcb}
0
{RHpcb}
0
{Cp cb}
PCB10
{Cp cb}
I42
{RHpcb}
0
{RHpcb}
0
{Cp cb}
PCB11
{Cp cb}
P2
C1
{Cbase}
R28
{RLpcb1}
I31
R29
{RLpcb1}
{RHpcb}
I39
+ -
R34
{RHpcb}
0
{Cp cb}
PCB14
I43
R50
{Rbase*2}
{RHpcb}
0
PCB12
{RHpcb}
0
{RHpcb}
0
{Cp cb}
PCB15
{Cp cb}
R33
{RLpcb1*2}
I47
{RinsB}
R89
{RHpcb}
0
0
C 10
0
R13
{Rbase*2}
{RHpcb}
0
{Cp cb}
{Cp cb}
{RinsB}
R90
PCB16
{RintG }
R40
{RLpcb1*2}
R41
{RLpcb1}
I32
R42
{RLpcb1}
{RHpcb}
PCB18
R53
{RLpcb1*2}
R54
{RLpcb1}
I33
{RHpcb}
{RHpcb}
0
R55
{RLpcb1}
PCB26
R67
{RLpcb1}
I37
+ -
R56
{RLpcb1}
{RHpcb}
0
{RHpcb}
0
R68
{RLpcb1}
C 17
{RHpcb}
0
{Cp cb}
PCB20
I41
R57
{RLpcb1}
I45
{RHpcb}
0
{Cp cb}
R69
{RLpcb1}
{RHpcb}
0
{Cp cb}
PCB24
R70
{RLpcb1}
PCB21
R59
{RLpcb1*2}
I49
P17
C16
{Cbase}
+ -
R65
0
C 19
0
R39
{Rbase*2}
{RHpcb}
0
R63
0
C 18
R58
{RLpcb1}
0
{Cp cb}
+ -
R62
C11
{Cbase}
R52
C 15
{RHpcb}
0
{Cp cb}
R71
{RLpcb1}
0
C 20
PCB28
R73
PCB29
R74
PCB30
R75
PCB31
R76
PCB32
R78
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
{RHpcb*2}
Q5
C2 {RinsB}
{Cbase}
R60
R4
{Rbase*2}
R61
Q3
{Cbase} C4 {RinsB}
R80
{Rbase}
{Rbase}
{Rbase*2}
R62
Q2
C5
{RinsB}
{Cbase}
R90
{Rbase*2}
{Rbase}
R64
Q10
{Cbase} C7 {RinsB}
0
R17
{Rbase}
G15
R36
R11
TEM2
R12
{Rbase}
R65
Q9
{Cbase} C8 {RinsB}
0
R14
{Rbase}
R18
P16
P15 0
{RinsB}
Q20
C17
{RinsB}
{Cbase}
R530
{Rbase}
R66
Q8
C9
{RinsB}
{Cbase}
0
R15
{Rbase}
R38
Q19
C18
{RinsB}
{Cbase}
R500
{Rbase}
{Rbase}
R67
Q7
C10 {RinsB}
{Cbase}
0
R16
{Rbase*2}
R85
R44
Q6
{RintG }
Q18
C19
{RinsB}
{Cbase}
R510
{Rbase}
{Rbase}
R55
Q17
C20
{RinsB}
{Cbase}
R520
Q11
R100
G13
R99
G12
{RintG }
Q16
R57
R98
G11
{RintG }
G8
{Rbase*2}
R56
P10
R78 {Rbase*2}
R79 {Rbase*2}
R80 {Rbase*2}
R81 {Rbase*2}
R82
Q25
Q24
Q23
Q22
C23
C25
C22 {RinsB}
C24 {RinsB}
{RinsB}
{RinsB}
{RinsB}
{Cbase}
{Cbase}
{Cbase}
{Cbase}
P14 0
P13 0
P12 0
P11 0
R101
AFEE board model diagram
R84
{RintG }
G7
R37
R54
C21
{Cbase}
Q1
G6
TEM1
R68 {Rbase}
R69 {Rbase}
R70 {Rbase}
R71 {Rbase}
R72
Q15
Q14
Q13
Q12
C13
C12
C15
C14 {RinsB}
{RinsB}
{RinsB}
{RinsB}
{Cbase}
{Cbase}
{Cbase}
{Cbase}
0
0
0
0
R43
R40
R41
R42
{Rbase}
{Rbase}
{Rbase}
{Rbase*2}
R91
R86
G14
TEM3
TEM4
{RintG }
{RintG }
R45
R46
R47
R48
P9
R73 {Rbase}
R74 {Rbase}
R75 {Rbase}
R76 {Rbase}
R77
{RintG }
P. Prat
Q4
C3 {RinsB}
{Cbase}
R70
{Rbase}
G16
R10
R60
{RinsB}
PCB25
R72
{RLpcb1*2}
PCB27
R77
R3
{Rbase*2}
P8
R490
{Rbase*2}
{RHpcb}
0
{Cp cb}
R59
P18
+ -
0
C 14
+ -
0
R46
{RLpcb1*2}
I48
R50
{Cp cb}
R61
0
R45
{RLpcb1}
+ -
0
C 13
+ -
R60
{Cp cb}
PCB23
R66
{RLpcb1*2}
0
C 12
I44
R49
{Cp cb}
PCB19
{Cp cb}
C 16
PCB22
0
R44
{RLpcb1}
+ -
R48
{RHpcb}
0
R64
I40
+ -
R47
C 11
PCB17
I36
+ -
R51
R43
{RLpcb1}
{Rbase*2}
P7
R63
C6
{Cbase}
R39
0
C9
P5
P19
+ -
R37
0
C8
R32
{RLpcb1}
+ -
R36
0
C7
R31
{RLpcb1}
+ -
R35
0
C6
PCB13
I35
+ -
R38
R30
{RLpcb1}
P4
R2
G5
{RintG }
P6
{RintG }
R27
{RLpcb1*2}
R96
G4
{RintG }
P3
R1
R58
0
{Cp cb}
R95
G3
{RintG }
P20
R26
C5
R94
G2
{RintG }
P1
+ -
0
C4
R93
G1
R20
{RLpcb2*2}
I46
R24
0
C3
R19
{RLpcb2}
+ -
R23
0
C2
R18
{RLpcb2}
+ -
R22
0
C1
PCB8
I34
R88
{RintG }
Q21
R97
G10
{RintG }
G9
{RintG }
Base-plate model diagram
6.2-13
R 1 3 - D
{ 2 * R v }
R 1 3 - 4
R 1 3 - B{ 2 * R e }
{ 2 * R h }
N 1 3 - 2
N 1 2 - 4
{ R lo n g }
R2
C 1 3
{ Ct h / 2 }
0
R 1 2 - 4
N 1 2 - 2
N 1 1 - 4
R 1 3 - 3
{ 2 * R e }
{ R c s i}
R 1 2 - D
{ Rv }
C 1 2
{ Ct h }
R L 1 - 2
R1
N 1 3 - 3
{ 2 * R h }
R 1 3 - 1
{ 2 * R e }
R 1 2 - C
0
R 1 1 - 4
{ Re }
N 1 1 - 2
N 1 0 - 4
N 1 3 - 1
R 1 3 - H
R 1 2 - 3
{ Re }
{ R c s i}
R 1 1 - G
{ Rv }
R 1 0 - 4
{ Re }
0
R 9 - 4
{ Rh }
N 8 - 4
R 1 1 - 1
R 1 0 - C{ Re }
{ R c s i}
R 1 0 - G
{ Rv }
0
R 8 - 4
{ Re }
{ Rh }
N 7 - 4
R 9 - C
{ R c s i}
R 9 - G
{ Rv }
0
R 7 - 4
{ Re }
{ Rh }
N 6 - 4
R 9 - 1
{ Re }
R 8 - C
{ R c s i}
R 8 - G
{ Rv }
0
{ Rh }
N 5 - 4
R 8 - 1
{ Re }
R 7 - C
{ R c s i}
C 7
{ Ct h }
0
R 5 - 4
{ Re }
{ Rh }
N 5 - 2
N 4 - 4
R 6 - C
{ R c s i} R 7 - G
R 6 - G
{ Rv }
0
R 4 - 4
{ Re }
N 4 - 2
N 3 - 4
R 6 - 1
{ Re }
R 5 - C
{ R c s i}
R 5 - G
{ Rv }
0
R 3 - 4
{ Re }
{ Rh }
N 3 - 2
N 2 - 4
R 5 - 1
{ Re }
R 4 - C
{ R c s i}
R 4 - G
{ Rv }
0
R 3 - 2
{ Re }
{ Re }
N 2 - 2
R 4 - 3
{ Re }
{ R c s i}
R 3 - G
{ Rv }
R 2 - 4
{ Rh }
N 1 - 4
R 4 - 1
{ Re }
R 3 - C
{ R c s i}
R 2 - G
{ Rv }
0
R 1 - 4
{ 2 * R e }
R 3 - 1
{ Re }
R 2 - C
{ R c s i}
R 1 - G
{ 2 * R v }C 1
{ Ct h / 2 }
N 1 - 2
N 3 - 3
R 1 - H
R 1 - 1
{ 2 * R e }
R 1 - 2
{ 2 * R e }
{ R lo n g }
N 3 - 1
R L 1 2 - 1
CNRS/IN2P3-LLR
Ecole Polytechnique
N 1 3 - 4
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis Results

P. Prat
Static Results – Good Correlation
– Hot Case
Location
N° Node
Base Plate – Center
Base plate –Face X+ Side
Base plate –Face X- Side
Base plate – Face Y+ Side
Base plate – Face Y- Side
Side panel – Center Face X+
Side panel – Center Face XSide panel – Center Face Y+
Side panel – Center Face YComposite Structure - Top
Composite Structure – Center
AFEE board – face X+
AFEE board – face XAFEE board – face Y+
AFEE board – face YGrid
TEM
Tracker
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
grid
tem
tracker
TEMP Ta
(°C)
Simplified
model
TEMP Tb
(°C)
Detailed
model
18.74
18.542
18.542
18.542
18.542
19.64
19.64
19.64
19.64
19.188
19.171
22.515
22.515
22.515
22.515
18
34
18.5
18.64
18.55
18.55
18.53
18.53
19.4
19.4
19.43
19.43
19.02
19.01
22.52
22.52
22.51
22.51
18
34
18.5
6.2-14
Ta –Tb (°C)
0.1
-0.008
-0.008
0.012
0.012
0.24
0.24
0.21
0.21
0.168
0.161
-0.005
-0.005
0.005
0.005
0
0
0
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis Results

P. Prat
Static Results – Good Correlation
– Cold Case
Location
N° Node
Base Plate – Center
Base plate –Face X+ Side
Base plate –Face X- Side
Base plate – Face Y+ Side
Base plate – Face Y- Side
Side panel – Center Face X+
Side panel – Center Face XSide panel – Center Face Y+
Side panel – Center Face YComposite Structure - Top
Composite Structure – Center
AFEE board – face X+
AFEE board – face XAFEE board – face Y+
AFEE board – face YGrid
TEM
Tracker
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
grid
tem
tracker
TEMP Ta
(°C)
Simplified
model
-14.52
-14.588
-14.588
-14.588
-14.588
-13.483
-13.483
-13.483
-13.483
-14.024
-14.041
-10.608
-10.608
-10.608
-10.608
-15
-11
-17
6.2-15
TEMP Tb
(°C)
Detailed
model
-14.57
-14.59
-14.59
-14.61
-14.61
-13.72
-13.72
-13.69
-13.69
-14.15
-14.15
-10.6
-10.6
-10.4
-10.4
-15
-11
-17
Ta –Tb (°C)
0.05
0.002
0.002
0.022
0.022
0.237
0.237
0.207
0.207
0.126
0.109
-0.008
-0.008
-0.208
-0.208
0
0
0
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Analysis Results

Transient Results – Good Correlation
– A 10°C Temperature Step was Applied on the Grid in Order to
Verify the Correlation Between the Simplified and Detailed Models
Temperature (°C)
Transient Response - Simplified Model
16
14
AFEE Y - Center (D14)
12
10
Side-panel Y - Center (D8)
8
6
4
Comp. Structure - Top (D10)
2
0
Base-plate - Center (D1)
Comp. Structure - Center (D11)
0
20000
40000
60000
80000
100000
Time (s)
Temperature (°C)
Transient Response - Complex Model
16
14
AFEE Y - Center
12
10
Side-panel Y - Center
8
6
4
Comp. Structure - Top
2
0
Base-plate - Center
Comp. Structure - Center
0
20000
40000
60000
80000
100000
Time (s)
P. Prat
6.2-16
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Design Status

Detailed and Simplified Thermal Models Have Been Developed with
Material and Thermal Contact Assumptions

The Temperature Build-Up Time of the CDEs is Very Dependent on
the Contact Resistances Between Parts (Aluminum-Composite,
Titanium-Aluminum, CDE-Composite):
– 24:30 hr – 32:00 hr for the Qualification Thermal Cycle
• A Step of Temperature Applied on the Grid: –30°C to +50°C
With a Temperature Slope of 10°C / Hour
• Time Determined at +49°C
• Min and Max Contact Thermal Resistances are in a Ratio 1:12
P. Prat
6.2-17
CNRS/IN2P3-LLR
Ecole Polytechnique
GLAST LAT Project
CAL Peer Design Review, Mar 17-18, 2003
Thermal Design Status - Continued

The Detailed and Simplified Models Will Be Updated According
to the Thermal Balance Test Results Achieved on the EM
– Model Update Will Only Affect the Parameter Values
– The Model of the Structure Will Not Change

The Current Thermal Simulations Show That the Thermal
Design Is Sound:
– The Max Difference of Temperature Between CDEs is 0.7°C,
Accounting for Max Values of Contact Thermal Resistances

Independent Review of Analysis is Complete
P. Prat
6.2-18
CNRS/IN2P3-LLR
Ecole Polytechnique