下載/瀏覽

Download Report

Transcript 下載/瀏覽

鈦金屬與FA混合物與鈦合金燒結
後浸泡SBF後之生物活性分析
學生:陳聖元
指導教授:郭聰源
2016/7/15
1
目錄
•
•
•
•
•
•
前言
文獻回顧
實驗規劃
實驗結果
結果與討論
未來展望
2
前言
•為了增進鈦合金的生物活性,本篇使用了
一種結合鈦和FA且已經被應用在負載關節
的方法,並加入銀金屬以及加壓燒結的變
數以期有降低感染率、提高鈦合金基材和
Ti/FA混合物的平均緻密度、釋放機能性離
子和的效果
3
文獻回顧
•FA是良好的骨頭及牙齒植入物的生醫材料,因為
它不只有近似於HA的效果並且還可以釋放氟離子
•Ti-6Al-4V有良好的生物相容性、抗腐蝕性及機械
性質(拉伸強度及疲勞強度)但和周圍組織
•Ag能傷害病毒的DNA及RNA,達到降低感染率的效
果
4
實驗規劃(1/2)
1. 將純鈦粉末和5%和10%的FA粉末在氬氣環
境下混合48小時
2. 將25um的銀片鋪在長8mm寬8mm厚1.7mm的
鈦合金並用一公克的Ti/FA混合物平鋪在
銀上,用單軸350MPa的壓力將
3. 在氬氣環境下用攝氏1100及0.1MPa的壓力
燒結該處理後的試件一小時
5
實驗規劃(2/2)
4. 將燒結時0.1MPa的條件或銀的條件除去重
複上述動作達到4個結果
5. 浸泡加入1g/L的NaN3的Kokubo’s SBF
6. 以SEM觀察切面、鈣化物沉澱情況以及用
PH值測量器和
6
實驗結果(1/5)SEM觀察切面
(a)和(b)有
些許緻密
度差異而
在加入Ag
後(c)(d)
緻密度變
化度大(d)
SEM micrographs of the cross-section of the specimens (left: T5F on Ti6Al4V; right: T10F on Ti6Al4V) sintered
under various conditions: (a) and (b) without pressure or Ag; (c) and (d) with Ag interlayer but without external
pressure
7
實驗結果(2/5)SEM觀察切面
而在
(e)(f)加
入外加壓
力後可以
看出混合
物離子充
分的散布
於交界面
間,良好
分佈
SEM micrographs of the cross-section of the specimens (left: T5F on Ti6Al4V; right: T10F on Ti6Al4V) intered
under various conditions: (e) and (f) with external pressure but without Ag interlayer; (g) and (h) with both Ag
interlayer and external pressure
8
實驗結果(3/5)SEM觀察SBF浸泡
SEM micrographs of T5FAT surface after immersion in the SBF for various times: (a) 0 h; (b) 8 h; (c) 1 day; (d) 3 days; (e) 7 days; (f) 14
days.
9
實驗結果(4/5)
SEM micrographs of T10FAT surface after immersion in the SBF for various times: (a) 0 h; (b) 8 h; (c) 1 day; (d) 3 days; (e) 7 days; (f) 14
days.
10%FA的混合粉末顯然比5%FA混合粉末的效果要好,
但是最好的效果還是要繼續往上試驗
10
實驗結果(5/5)
•
藉由ICP-AES
及PH測量器
可以看出
1. PH值呈現鹼
性有助於細胞
的生長範圍
2. 機能性離子(F、
Ag)在浸泡
SBF後,有效
釋放
11
Variations of pH value and the concentration of calcium, phosphorous, fluorine and silver in
the SBF with the soaking time.
結果與討論
• 在藉由SEM、PH值測量器和ICP-AES的結果
後,得知
1. 此方法藉由提高FA的濃度可能還有更好的表
現
2. 藉由提供壓力的大小能提高分佈的平均性,
有效達到降低燒結後微結構因緻密度產生應
立集中效應
12