Transcript Document
• The right choice: Windows and Door Frames Exterior Fixtures Hand Rails Electrical Boxes Hurricane Shutters Screen Enclosures Back out old screw Simply enlarge hole with Tapper+ Bit No need to patch hole Drive a new Tapper+ Xtreme You’re Done! Code Approval 2012, 2009, 2006 and 2003 IBC & IRC ESR-3068 2010 Florida Building CodeBuilding & Residential ESR-3068 FBC Supplement Miami-Dade County Notice of Acceptance NOA12-1205.10 Normalized Tension Load - 3,000 psi concrete 3000 Load (lbf) 2500 2000 1500 1000 500 0 Powers 5/16" Tapper+ Xtreme Powers 3/8" Tapper Elco Ultracon Hilti Quick Con II *Based on Manufacturer Published literature, 1-3/4” embedment Buildex Tapper XL ITW T a p c o n P O W E R S When salt spray tested head to head against the ITW Tapcon® with the Climaseal coating the Powers Tapper+ PermaSeal® Coating outperformed the competition with no visible red rust. • Approved for High Velocity Hurricane Zones (HVHZ)! • Great for securing Hurricane shutters •Superior load carrying capacity than traditional “blue screws” • Powers’ Patented Perma-Seal® coating provides excellent corrosion resistance in extreme weather environments. Note the fast install time and minimal effort during installation due to the coarse thread. 1. Using the included 5/16” Tapper+ SDS Bit, drill a hole into concrete. 2. With a #3 bit tip or 5/16” hex socket depending on head style mount the anchor into the socket 3. Drive the anchor with an impact wrench (max 115 ft-lbs.) Recommended DEWALT DCF895C2 4. After installation notice the on the head. The head diameter is the same size as the ¼” Tapper+. Description Powers 5/16" Silver Tapper+ Xtreme Buildex Tapper XL* Hilti Quick Con II Elco Ultracon 5/16x 1-3/4 Hex head 5/16x 2-1/4 Hex head 5/16x 2 3/4 Hex head 5/16x 3-1/4 Hex head 5/16x 4 Hex Head 5/16x 5 Hexhead 2200SD 2202SD 2204SD 2206SD 2208SD 2210SD 3395902 / 3397902 3398902 - 00433021 00433022 00433023 00433024 00433026 - ELG481 ELG486 ELG491 ELG501 ELG506 ELG511 5/16x 2-1/4 Flat head 5/16x 2 3/4 Flat head 5/16x 3-1/4 Flat head 5/16x 4 Flat Head 2212SD 2214SD 2216SD 2218SD - 00433049 00433050 00433051 00433054 ELG941 ELG948 ELG960 ELG979 5/16x 1-3/4 Trim Hex head 5/16x 2-1/4 Trim Hex head 5/16x 2 3/4 Trim Hex head 2230SD 2234SD 2236SD - - ELG482 ELG487 ELG492 5/16x 2-1/4 Trim Flat head 5/16x 2 3/4 Trim Flat head 5/16x 3-1/4 Trim Flat head 2242SD 2244SD 2248SD - - ELG801 ELG831 ELG861 *Only available in button head style *Bronze available by special order For Ordering Information Download the Brochure here: http://www.powers.com/pdfs/catalogs/49159_tapperplus_hi.pdf Installation Kit Includes: #3 Philips Impact Power Bit 5/16” Impact Ready Nut Driver 5/16“ x 6” SDS+ Tapper+ Bit 5/16“ x 8” SDS+ Tapper+ Bit Robust Powers case • Available in a choice of 4 different Head styles and a variety of colors to suit your application. Trim Hex Hex Flange Flat Trim Flat • Bonus SDS Tapper+ Bit comes with every box of Tapper+® Xtreme screw anchors!! • Contact your local Powers representative today!