Transcript MFGT 290 MFGT Certification Class Chapters 13, 14, and 15: Engineering Materials-

MFGT 290
MFGT Certification Class
Chapters 13, 14, and 15: Engineering MaterialsPlastics, Composites, and Ceramics
Professor Joe Greene
CSU, CHICO
MFGT 290
1
Chap 13: Plastics
•
•
•
•
•
•
•
•
Plastics
Polymerization
Polymer Structures
Thermoplastics
Engineering Thermoplastics
Thermoset Polymers
Processing of Plastics
Review Questions
2
Definition of Plastics
All Materials
Simple
Liquids
Gases
Metals
Ceramics
Solids
Polymers
(polymeric molecules)
Thermoplastics
Heat Forming
Thermosets
Heat Setting
Elastomers
3
Introduction
• Polymeric materials can be either
– Thermoplastics, thermosets, and elastomers.
– Each section is presented in appropriate groups
• Thermoplastics- Heat Forming materials (Can reheat & form again)
– Carbon bonds are Saturated and are single bonds.
– Come in a variety of forms
• Pellets, powder (1-100 microns), flake, chip, cube, dice,
• Shipped in packages of choice
– Bags (50 lbs), drums (200 lbs), boxes, cartons, gaylords (1000 lb),
– Tank-truck loads (15 tons), rail cars (40 – 80 tons)
• Bulk supplies are stored in silos and conveyed pneumatically
• Thermosets- Heat Setting materials (Once set can’t reform -like
cooked eggs)
– Carbon bonds are Unsaturated and have some double bonds.
– Supplied in powder or liquid form
• Supplied in drums, tank-trucks, and railroad cars.
• Rubbers are supplied in bale form.
4
Commercial Thermoplastics
• Olefins
•
– Unsaturated, aliphatic hydrocarbons made from ethylene gas
– Ethylene is produced by cracking higher hydrocarbons of natural gas or
petroleum
LDPE commercialized in 1939 in high pressure process
• Branched, high pressure, and low density polyethylene
•
HDPE commercialized in 1957 in low pressure process
• Linear, low pressure, high density
• Medium density PE and other PE, UHMWPE, LLDPE
• The higher the density the higher the crystallinity
– Higher the crystallinity the higher the modulus, strength, chemical resistance,
• PE grades are classified according to melt index (viscosity) which is
a strong indicator of molecular weight.
– Injection molding requires high flow, extrusion grade is highly elastic,
thermoforming grade requires high viscosity or consistency
• Other commodity (cheap) plastics
– PP, PS, PVC (or vinyl), ABS, PMMA (Acrylic)
5
Major Plastic Materials
1994
•
•
•
•
•
•
•
•
LDPE
HDPE
PVC
PP
PS
PU
PET
Phenolic
Total
6.4 M metric tons
5.3 M metric tons
5.1 M metric tons
4.4 M metric tons
2.7 M metric tons
1.7 M metric tons
1.6 M metric tons
1.5 M metric tons
28.6 M metric tons (82% of market)
6
Recycling of Plastics
• State and Federal Legislation
• PET bottle recycling
• Codes for plastics
–
–
–
–
–
–
–
1
2
3
4
5
6
7
PET
HDPE
Vinyl/PVC
LDPE
PP
PS
Other
7
States of Thermoplastic Polymers
• Amorphous- Molecular structure is incapable of forming regular
order (crystallizing) with molecules or portions of molecules
regularly stacked in crystal-like fashion.
• A - morphous (with-out shape)
• Usually transparent (Clear bags)
• Less shrinkage with amorphous materials.
Amorphous
Polymers
•ABS
Acrylics
•Polycarbonate PS
•Polyurethanes PPO
•Phenoxy
PVC
•SAN
8
States of Thermoplastic Polymers
• Crystalline- Molecular structure forms regular order (crystals) with
molecules or portions of molecules regularly stacked in crystal-like
fashion.
• Most crystalline polymers are semi-crystalline because very few
plastics are 100% crystalline. All have both regions that are
crystalline and some that are amorphous
• Usually Opaque and not transparent
• More molding shrinkage with
Crystalline Materials
– crystalline materials.
•LDPE
•PET
HDPE
PP
PBT
•Polyamides
•PMO
PEEK
•PPS
PTFE
•LCP (Kevlar)
9
Functional Groups
• Certain chemical characteristics associated with various groups of
atoms, called functional groups.
• Particular groups of atoms occur in a large molecule, the
characteristic chemistry is anticipated.
– Example, PP has Functional groups can be attached to basic groups of carbon
atoms by replacing on H atom.
H H
H H
H H
H H
C C
C C
C C
C C
H CH3
n
H CH3
n
H CH3
n
H CH3
n
– Note: PP is Mostly Isotactic- CH3 on one side of polymer chain (isolated).
Commercial PP is 90% to 95% Isotactic and not Atactic (random) or syndiotactic
10
Functional Groups
• Various molecules of carbon, hydrogen and oxygen illustrating the
differences properties with different atomic arrangements
•
•
•
•
•
•
isopropyl alcohol- rubbing alcohol
methylethyl ether- anesthetic
acetone- common solvent
methyl acetate- sweet chemical perfume
propionaldehyde- sharp smelling chemical
propanoic acid= related to vinegar
• Aromatic group- PBT, PET, PC, PEEK, PS all have aromatic
– 6 carbon atoms bonded together with double bonds
– Highly aromatic if have several aromatic groups
• Aliphatic group- LDPE, HDPE,
– single and double bonded carbons with other atoms
11
Polymers Units
• Just as 2 carbons atoms are bonded together in ethane, three, four, or
more carbons can be bonded in chain-like arrangement, sometimes
thousands of atoms long.
• Long chains of atoms are poly-mers (many-mers or units)
• Figure
– Polyethylene
PP
PS
PVC
H H
H H
H H
H H
C C
C C
C C
C C
H H
H CH3
n
n
H
n
H Cl
n
– Note: PP is Mostly Isotactic- CH3 on one side of polymer chain (isolated).
Commercial PP is 90% to 95% Isotactic and not Atactic (random) or syndiotactic
12
Complex Polymers
• Polymer chains with atoms other than carbon
– Usually polymer chains with C and N, O, S, F, and Cl
• PVC has Cl; Nylon has O and N; Polyurethane has O and N
• PET has O and benzene ring; PC has O and benzene ring
• Bonding in Plastics (No metallic or Ionic bonds_ Just Covalent)
– Covalent bonds are dominate bonding between C and other atoms.
• Secondary bonding and Intermolecular Forces
• Van der Waal’s Forces- weak attraction not in plastics
• Dipole interactions- Part of molecule is more electronegative than other part causing
one side to be partially negative and the other partially positive.
– Hydrogen bonding- Very important for some plastics- Like Nylon
– Causes physical properties to change. Like tensile strength and melting point
– Nylon 6 has higher tensile strength and melting point than Nylon 12 because
» Nylon 6 has 1 dipole + 1 hydrogen bond for every 6 Carbon atoms in chain.
» Nylon 12 has 1 dipole and 1 hydrogen bond every 12 Carbon atoms
– Dipole induces polarity and occurs if
» C-Cl single bond (like PVC); C-Fl single bond (Like PTFE); C=O double
bond (like Nylon, PET, PU, PC)
– Hydrogen bonds induces polarity and occurs if
» C-OH single bond (like PU-polyurethane); N-H Single bond (Like PU, 13
Formation of Polymers
• Addition (or Chain-Growth) Polymerization
– Most Commodity (cheap) plastics
– Instantaneously, the polymer chain forms with no by-products
– Chain-reaction mechanism that proceeds by several sequential steps
as shown in Figure 2.20. Polymerization begins at one location on
the monomer by an initiator
• Condensation (or Step-wise) Polymerization
– Most Engineering plastics (pellets of Nylon, PC, PET, Polyurethane)and
themosets (liquids of epoxy, polyester, polyurethane)
– Step-growth polymerization proceeds by several steps which result in byproducts.
– Monomers combine to form blocks 2 units long
– 2 unit blocks form 4, which intern form 8 and son on until the process is
terminated.
– Results in by-products (CO2, H2O, Acetic acid, HCl etc.)
14
Nylon (or polyamide) and PC
• The repeating -CONH- (amide) link
• Polymerized with condensation reaction
– Nylon 6- Polycaprolactam: [NH(CH2)5CO]x
– Nylon 6,6- Polyhexamethyleneadipamide:
• [NH(CH2)6NHCO (CH2)4CO]x
– Nylon 12- Poly(12-aminododecanoic acid)- [NH(CH2)11CO]x
• Polycarbonates are linear, amorphous polyesters because they
contain esters of carbonic acid and an aromatic bisphenol (C6H5OH)
• Polymerized with condensation reaction
O
CH2
O
C
CH2
O
C
n
15
Homopolymers
• Plastics Involving Three+ Substitutions (use Table 3.2)
Z
Y
C
C
W X
n
e.g. PTFE
polytetrafluoroethylene
(Teflon)
F
F
C
C
F
F
n
16
Copolymers and Ter Polymers
• Plastics Involving Two mers in chain or 3 mers (ABS)
e.g. SAN
styrene
acronitrile
H
H
H
H
C
C
C
C
H
C:::N m
H
n
•Structure of two mers can be OR the same three mers with a C
–Alternating- ABABABABABABAB
–Random copolymer- AABBABBBAABABBBAB
–Block copolymer- AABBBAABBBAABBBAABBB
–Graft copolymer- AAAAAAAAAAAAAAAAAAAAAAAAAA
B
B
B
B
B
B
B
B
B
17
Thermosets
• Thermosets are polymers that undergo a chemical reaction
during the polymerization.
• Thermosetting reaction is not reversible under heat.
• Epoxy
– Standard epoxy is based on bisphenol A and epichlorohydrin.
– Properties include good adhesion to many substrates, low
shrinkage, high electrical resistivity, good corrosion resistance, and
thermal.
– Processing is achieved without generation of volatiles.
18
• Polyester
Polyester and Polyurethane
– Thermoset reaction between a difunctional acid (or anhydride) and a
difunctional alcohol (glycol)
– Heat or radiation can trigger the cross linking reaction
– Accelerators (or promoters) speed up the reaction.
– Condensation Reaction results in CO2 and H2O.
– Monomer required to polymerize, e.g., Styrene at 30% to 50% in commercial
polyester systems
• Polurethane
– Reaction between isocyanate and alcohol (polyol). Condensation Reaction
results in CO2 and H2O.
– Crosslinking occurs between isocyanate groups (-NCO) and the polyol’s
hydroxyl end-groups (-OH)
– Thermoplastic PU (TPU) have some crosslinking, but purely by physical means.
These bonds can be broken reversibly by raising the material’s temperature, as
in molding or extrusion.
19
Thermoplastic Elastomers, Natural Rubber
• Thermoplastic Elastomers result from copolymerization of two or
more monomers.
– One monomer is used to provide the hard, crystalline features, whereas the other
monomer produces the soft, amorphous features.
– Combined these form a thermoplastic material that exhibits properties similar to
the hard, vulcanized elastomers.
• Thermoplastic Urethanes (TPU) were the first Thermoplastic
Elastomer (TPE) used for seals gaskets, etc.
• Other TPEs
–
–
–
–
Copolyester for hydraulic hoses, couplings, and cable insulation.
Styrene copolymers are less expensive than TPU with lower strength
Styrene-butadiene (SBR) for medical products, tubing, packaging, etc.
Olefins (TPO) for tubing, seals, gaskets, electrical, and automotive.
• Natural Rubber is an elastomer that comes from rubber trees in Asia
– Properties are increased by vulcanization with sulfur to make it strong.
– Automobile tires use a large amount of Natural rubber and SBR
20
Plastics Questions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
A bond between 2 carbon atoms is a _______ bond.
A CH3 groups is called a __________ group.
A dash between atoms indicates a ______ bond.
The small repeating units that make up a plastic molecule are called ___________
What does poly mean? ___________
3 types of intermolecular forces found in plastics are ___________ , ____________, and
____________.
What type of bonding makes Nylon 6 stronger than nylon 12? _____________
Crystalline plastics are more rigid and not as transparent as _________ plastics.
A _______ material may be softened repeatedly when heated and hardened when cooled.
The term used to describe tying together adjacent polymer chains is _______
If the different mers make up the composition of a polymer , it is called a ______.
A Hydrogen molecule which contains some double bonds is called ________.
Is PVC a copolymer? _________ Explain- _____________________________.
What is the general structure of an alternating copolymer? __________________.
If a carbon chain has a methyl side group, is it branched? _________ Explain_____________________________.
If a material is transparent, is it crystalline? ____________
What effect do dipoles and hydrogen bonds have on melting point of polymers ___________
Is residual stress synonymous with orientation? ____________________
How does the tensile strength and melting point change with increasing crystallization? ______
21
Processing of Polymers
• Thermoplastics
– injection molding, extrusion, blow molding, thermoforming,
rotational molding, compression molding
– Usually uses high pressure processes and imparts high residual
stresses on the material which an cause warping in part.
• Thermosets
– compression molding, reaction injection molding, resin transfer
molding, casting, hand layup, etc.
• Elastomers
– compression molding, extrusion, injection molding, casting.
22
Injection Molding Process and Cycle Time
23
Extruder Equipment
• Exit zone- die
– die imparts shape on the material, e.g., rod, tube, sheet, channel
– exit material is called extrudate
– extrudate swells at end of die due to normal forces from the polymer flow, called die
swell
Die Swell
•
Cooling zone
– water bath or air cooled to lower the temperature below Tg
• Auxiliary equipment
– puller
– rollers for proper thickness
– Wind-up or cut off
24
Compression Molding Process
• Materials
•Thermosets: Polyester, Vinyl ester, or Epoxy resins with glass fiber
•Sheet Molding Compound (SMC), Bulk Molding Compound (BMC)
•Thermoplastics: Polypropylene, polyester, or others with glass fibers
•Glass Mat Thermoplastic (GMT), thermoplastic BMC
•Elastomers: Thermoplastic or Thermoset rubbers
•Thermoplastic Olefin (TPO), Thermoplastic Elastomer (TPE), Thermoplastic
Rubber (TPR)
•Thermoset Styrene Butidiene Rubber
Thermoplastic:
Heat Plastic
prior to molding
Thermosets:
Heat Mold
during molding
25
Resin Transfer Molding Process
Ref: MSU Tutorial- http://islnotes.cps.msu.edu/trp/liquid/rtm/
•Materials
•Thermosets: Polyester, Vinyl ester, or Epoxy resins with glass fiber
26
Polyurethane Processing
• Polyurethane can be processed by
– Casting, painting, foaming
– Reaction Injection Molding (RIM)
27
Thermoset Reacting Polymers
• Process Window
– Temperature and pressure must be set to produce chemical reaction
without excess flash (too low a viscosity), short shot (too high a
viscosity), degradation (too much heat)
28
Compression Molding
• Compression molding was specifically developed for replacement of metal
components with composite parts. The molding process can be carried out with
either thermosets or thermoplastics. However, most applications today use
thermoset polymers. In fact,compression molding is the most common method
of processing thermosets.
29
Resin Transfer Molding
• In the RTM process, dry (i.e.,unimpregnated )
reinforcement is pre-shaped and oriented into skeleton of
the actual part known as the preform which is inserted into
a matched die mold.
• The heated mold is closed and the liquid resin is injected
• The part is cured in mold.
• The mold is opened and part is removed from mold.
30
Injection Molding Glass Reinforced Composites
• Plastic pellets with glass fibers are melted in screw,
injected into a cold mold, and then ejected.
Glass filled resin pellets
31
Chap 14: Composites
•
•
•
•
•
Composite Materials
Composite Construction
Composite Applications
Processing of Composites
Review Questions
32
Polymers Composites
• Objectives
– Define the components and difference types of composites.
– Explain the different types of composite construction and the reasons behind
them.
– Describe the various manufacturing methods used to produce composites.
– List the different reinforcing materials used in composites.
– List the various matrix materials used in composites.
• Excellent Web sites
– Michigan State http://islnotes.cps.msu.edu/trp/
– U of Delaware http://www.ccm.udel.edu/publications/CU/99/
– Cornell University http://www.engr.siu.edu/staff2/abrate/NSFATE/links.htm
33
Composites
• Composite definition
– A composite is a material comprised of two or more physically distinct
materials with at least one material providing reinforcing properties on
strength and modulus.
• Natural Composites
– Bone
– Wood
– Bamboo: Natures fiber glass due to pronounced fibrillar structure which is
very apparent when fractured.
– Muscle and other tissue
• Engineering Composites
– Reinforced concrete beams
– Thermoset composites: Thermoset resins (polyurethanes, polesters, epoxies)
• Glass fibers, Carbon fibers, Synthetic fibers, metalfibers, or ceramic fibers
– Thermoplastic composites (polypropylene, nylon, polyester,TPU,polyimide)
• Glass fibers, Carbon fibers, Synthetic fibers, metalfibers, or ceramic fibers
34
Composite Classifications
• Reinforcement Type
– Discontinuous (fibers are chopped and dispersed in matrix resin)
• Short fibers: fiber lengths 3mm or less (most injection molded materials)
• Long fibers: fiber lengths greater than 6 mm. (Some injection molded materials with
6mm fibers, Sheet Molding Compound (SMC) with 1” fibers, DFP Directed Fiber
Preforms for RTM and SRIM)
• Particulates: fibers is forms as spheres, plates, ellipsoids (some injection molded
materials reinforced with mineral fibers)
– Continuous (fibers are throughout structure with no break points)
• Glass roving: glass bundles are wound up in a packet similar to yarn.
• Roving is woven into several weaves using a loom machine like in apparel.
– Mat products: random swirl glass pattern.
– Woven product: roving is woven into machine direction (warp) and cross
direction (weft)
– Uni product: roving is woven in one direction with a cross thread given to hold
mat together.
35
Glass Fiber Applications
• Discontinuous (Chopped) Fiber
• Short fiber (L= 3mm) reinforcement for thermoplastic materials that are
injection molded (PP and Nylon)
• Long Fiber (L=6mm) reinforcement for thermoplastic materials that are
injection molded (Nylon)
• Chopped Fiber (L=12 mm to 25 mm) reinforcement for thermoset (SMC
and BMC) and thermoplastic BMC that are compression molded into parts
for Corvette hoods and doors, bumpers, Ford Truck box, and consumer box
shapes
• Continuous (Mat) Fiber
– Many types of weaves for automotive or aerospace applications
• Automotive: Viper hood with RTM, GM Truck box with SRIM, Corvette
floor pan with RTM
• Aerospace: Prepregs, Wings, Fuselages with RTM and SCRIMP
36
Carbon/Graphite Fibers
• Need for reinforcement fibers with strength and modulii
higher than those of glass fibers has led to development of
carbon
• Thomas Edison used carbon fibers as a filament for
electric light bulb
• High modulus carbon fibers first used in the 1950s
• Carbon and graphite are based on layered structures of
hexagonal rings of carbon
• Graphite fibers are carbon fibers that
– Have been heat treated to above 3000°F that causes 3 dimensional
ordering of the atoms and
– Have carbon contents GREATER than 99%
– Have tensile modulus of 344 Gpa (50Mpsi)
37
Carbon/Graphite Fibers
• Need for reinforcement fibers with strength and modulii
higher than those of glass fibers has led to development of
carbon
• Thomas Edison used carbon fibers as a filament for
electric light bulb
• High modulus carbon fibers first used in the 1950s
• Carbon and graphite are based on layered structures of
hexagonal rings of carbon
• Graphite fibers are carbon fibers that
– Have been heat treated to above 3000°F that causes 3 dimensional
ordering of the atoms and
– Have carbon contents GREATER than 99%
– Have tensile modulus of 344 GPa (50Mpsi)
38
Carbon/Graphite Fibers
• Manufacturing Process
– Current preferred methods of producing carbon fibers are from
polyacrylonitrile (PAN), rayon (regenerated cellulose), and pitch.
• PAN
– Have good properties with a low cost for the standard modulus
carbon
– High modulus carbon is higher in cost because high temperatures
required
• PITCH
– Lower in cost than PAN fibers but can not reach properties of PAN
– Some Pitch based fibers have ultra high modulus (725 GPa versus
350GPa) but low strength and high cost (Table 3-2)
39
Carbon/Graphite Fibers
• PAN Manufacturing Process Figures 3-3 and 3-4
– Polyacrylonitrile (PAN) is commercially available textile fiber and is a ready
made starting material for PAN-based carbon fibers
– Stabilized by thermosetting (crosslinking) so that the polymers do not melt in
subsequent processing steps. PAN fibers are stretched as well
– Carbonize: Fibers are pyrolyzed until transformed into all-carbon
• Heated fibers 1800°F yields PAN fibers at 94% carbon and 6% nitrogen
• Heated to 2300°F to remove nitrogen yields carbon at 99.7% Carbon
– Graphitize: Carried out at temperatures greater than 3200° F to
• Improve tensile modulus by improving crystalline structure and three dimensional
nature of the structure.
– Fibers are surface treated
• Sizing agent is applied
• Finish is applied
• Coupling agent is applied
– Fibers are wound up for shipment
40
Carbon/Graphite Fibers
• PITCH Manufacturing Process
• Pitch must be converted into a suitable fiber from petroleum tar
• Pitch is converted to a fiber by going through a meso-phase where the polymer
chains are somewhat oriented though is a liquid state (liquid crystal phase)
• Orientation is responsible for the ease of consolidation of pitch into carbon
– Stabilized by thermosetting (crosslinking) so that the polymers do not melt in
subsequent processing steps
– Carbonize: Fibers are pyrolyzed until transformed into all-carbon
• Heated fibers 1800°F
• Heated to 2300°F
– Graphitize: Carried out at temperatures greater than 3200° F to
• Improve tensile modulus by improving crystalline structure and three dimensional
nature of the structure.
– Fibers are surface treated
• Sizing agent is applied
• Finish is applied
• Coupling agent is applied
– Fibers are wound up for shipment
41
Carbon Fiber Mechanical Properties
• Table 3-2 (from MFGT 104)
Carbon Fiber Mechanical Properties
PAN Based
Tensile Modulus (Mpsi)
33 - 56
Tensile Strength (Msi)
0.48 - 0.35
Elongation (%)
1.4 - 0.6
Density (g/cc)
1.8 - 1.9
Carbon Assay (%)
92 - 100
PITCH Based Rayon Based
23 -55
5.9
0.2 - 0.25
0.15
0.9 - 0.4
25
1.9 - 2.0
1.6
97 - 99
99
42
Composites Have a Fiber Preform
• Fiber type
– Roving form that can be sprayed into a 3-D preform
– Roving form that is woven into a glass sheet and then formed to
shape (preform)
43
Sheet Molding Compound (SMC)
• SMC is the paste that is compression molded
– 33% polyester resin and stryrene, which polymerizes and
crosslinks
– 33% glass fibers (1” fibers)
– 33% Calcium Carbonate
44
Processing of Composites
• Open Mold processes
– Vacuum bag, pressure bag, SCRIMP
– autoclave: Apply Vacuum Pressure and Heat in an oven which can be 5 feet to
300 feet long
45
Structural RIM
• Fiber preform is placed into mold.
• Polyol and Isocyanate liquids are injected into a closed
mold and reacted to form a urethane.
46
Processing of Composites
• Open Mold processes
– Hand lay-up and Spray-up
– Filament winding
47
Composite Classifications
• Resin (or matrix) type
– Thermoset resins- those that undergo a chemical cross-linking reaction
• Epoxy;
• Silicone;
Polyester;
Melamine
Polyurethane;
Phenolic
– Thermoplastic resins- those that are formed under heat
•
•
•
•
Polyamines (nylon) (short and long fibers)
Polyesters (short and long fibers)
Polypropylene (short, long fibers and continuous fibers)
Other thermoplastic resins (short and long fibers)
• Fiber Reinforcements
– Glass for reinforced composites with concentrations less than 50% weight
– Carbon fiber for Advanced (aerospace) composites with concentrations greater
than 60% by weight.
– Kevlar fiber for Advanced (aerospace) composites.
• Core or Laminate structures
– A foam core material can be added (sandwiched) between the layers of resin and
fiber.
– Composite laminate has a core material with resin and fiber combinations
48
Processing and Composites Questions
1.
2.
3.
4.
5.
A composite material is a combination of a reinforcing element and ___________.
How are advanced composites are distinguished from reinforced plastics?_________
The fibers in advanced composites are usually made from what? ____________
What two functions does the matrix of a composite serve? ________________
Under what conditions should graphite fibers versus carbon fibers be used? _______
49
Chap 15: Ceramics
•
•
•
•
•
•
Ceramic Applications
Ceramic Structures
Glass
Advanced Ceramics
Processing of Ceramics
Review Questions
50
Introduction
• Ceramics are
– complex compounds and solutions that contain both metallic and
nonmetallic elements,
– heated at least to incandescence during processing applications,
– typically hard and brittle,
– exhibit high strength and high melting points,
– exhibit low thermal and electrical conductivity.
• Applications
– Pottery, brick, tile, glass, ovenware, magnets, refractories (resist high
temperature), cutting tools.
– Furnace linings and tiles for space shuttle due to high resistance to
heat.
– Superconductivity applications
51
Ceramics
• Traditional ceramics are made from clay, silica, and feldspar
• Structural clays for bricks, sewer pipes, drain tiles, and floor
tiles are made from natural clays made from three basic
components
• Traditional ceramic products are china, dental porcelain, and
sanitary-ware
• Technical ceramics are mainly pure compounds or nearly
pure compounds of primarily oxides, carbides, or nitrides.
– Carbides: with Silicon, tungsten, titanium, or tantalum Carbides
• Extreme hardness and wear resistance allows Use for cutting tools and abrasives
– Nitrides: with Boron, Silicon, or titanium Nitrides
• Ti-Nitride used as surface coating for cutting tools is brittle so B-nitride is added
• Boron Nitride is called cubic boron nitride (CBN) is used for cutting tools.
• Normally hot pressed in dry powder form onto useful
products.
52
Ceramics
• Ceramics comes from Greek word keramos, which means
potter’s clay.
• Ceramics are diverse group of nonmetallic, inorganic solid
compounds with a wide variety of compositions and
properties.
• Ceramics are crystalline compounds made up of metallic and
nonmetallic compounds with properties that differ from the
constituents.
• Ceramics in the form of pottery are among the oldest
products manufactured by humans.
– Clay is inexpensive material and is found throughout the world.
– Early clay products were sun dried not fired.
– Firing as used in pottery dates back to around 2000 to 3000 B.C.
53
Ceramics Properties
• Ceramics are crystalline like steel but have few free electrons
at room temperature and thus are low conductivity.
• Ceramics strengths have higher compressive than tensile.
• Ceramics are totally elastic, exhibiting no plasticity when
load is applied with little or no deformation prior to fracture.
• In general ceramics have the highest melting points of any
materials. Range from 3500F to as high as 7000F.
• Manufacturing of ceramics involves
–
–
–
–
–
–
–
blending fine starting materials with water to form mass that is shaped
formation includes extrusion, pressing, and casting,
use of potter’s wheel for cups, bowls, saucers, etc.
extruded to make bar shapes or poured into mold as slip slurry
after forming product is dried to remove water and fired for strength
forming provides fusion (sintering) and chemical reaction for bonding
glazing with ceramic coating for smooth surface
54
• Properties
Ceramics Materials
– Vary depending on composition, microstructure, and processing.
– Excellent resistance to
• compressive loads, abrasion, heat, and staining
• chemical attacks, weather attacks, bending (excellent rigidity)
– Poor resistance to tensile loads, spalling (thermal cracking ceramics)
– Most ceramics will crack if thermal cycled, except Pyrex glass which contains boric
oxide to provide expansion properties.
• Applications
– dielectric materials for capacitors with disk capacitors (mainly barium titanate)
being the most common.
– Semiconductor applications with sintered oxides, e.g., thermistors, which are
thermally sensitive resistors used for temperature control
– Piezoelectric ceramics (Barium titanate) is used in accelerometers and speakers. The
transducers convert input sound energy into electrical response or convert electrical
inputs into sound energy.
– Nanocomposites for plastics and composites
55
Glass
• Glasses are described as super-cooled liquids.
– Glasses do not behave like metals but more like polymers when
cooled from molten condition
• Metals exhibit a definite quantity of heat given off when cooled and form a
crystaline (or regular) structure when cooled.
– Heat is called heat of solidification
• Polymers exhibit changes in volume when cooled which may form a crystalline
or amorphous structure depending upon the nature of the polymer and versus
temperature that has an inflection point, know as glass transition temperature.
• Glass is a transparent silica product which may form an amorphous or
crystalline structure depending upon heat treatment during production.
• Glass do not exhibit any indication of transition or a clear point of inflection
when cooling from molten state.
• Glass is considered a viscous liquid when cooled from molten state.
• Glass has the appearance and feel of a solid material but will flow like a liquid
given time, e.g., thicker glass at bottom of window pane.
– Crystallinity of glasses is measured with X rays and X-ray diffraction.
• More crystalline the glass the more rays are diffracted
56
Glass Manufacturing
• Glass blowing process
– Glass blowpipe is a hollow iron tube from 4 to 5 ft long with a knob at
one end and a mouthpiece at the other end.
– Dip knob end into melted glass, where glass sticks to the end of pipe.
– Air is blown gently while rotating pipe which produces a hollow bulb
of glass, where the thickness of the bulb depends on size of bulb.
– The bulb cools and solidifies into a number of symmetrical shapes.
– Molds are used to rapidly cool glass and allow more many shapes,
including, bottles, dishes, lamps, and jars.
• Composition
– Glass is made primarily of sand (silicon dioxide)
– Silica or quartz glass is pure silicon dioxide (very stable)
– Window glass is made of sand (SiO2), limestone (CaCO3), and soda ash
(Na2Co3)
57