Transcript Document 7166984

Using the 8254 Timer-Counter
Understanding the role of the
system’s 8254 programmable
Interval-Timer/Counter
Motivation
• We want to explore the Pentium’s support
for multiprocessing (as distinguished from
multitasking, which we already examined)
• The algorithms for multiprocessor startup
will require us to use some ‘timed delays’
(for example, a delay of 10 milliseconds)
• Various other systems programming tasks
require the use of carefully timed delays
The 8254 PIT
• The 8254 Programmable Interval-timer is
used by the PC system for (1) generating
timer-tick interrupts (rate is 18.2 per sec),
(2) performing dynamic memory-refresh
(reads ram once every 15 microseconds),
and (3) generates ‘beeps’ of PC speaker
• When the speaker-function isn’t needed,
the 8254 is available for other purposes
Counter decrements when pulsed
COUNT REGISTER
CLK
MSB
MSB
LSB
LSB
LATCH REGISTER
GATE
STATUS
TIMER/COUNTER CHANNEL
OUT
Three timer/counter ‘channels’
8284
PCLK
1193182 Hz
CLK0
GATE0
Channel 0
Channel 1
Port 0x61, bit #0
OUT1
DRAM refresh
Port 0x61, bit #5
CLK2
GATE2
Interrupt IRQ0
Port 0x61, bit #4
CLK1
GATE1
OUT0
Channel 2
8254 PIT
+5 V
Port 0x61, bit #1
OUT2
AND
speaker
8254 Command-Port
7
6
CHANNEL
Channel-ID
00 = chn 0
01 = chn 1
10 = chn 2
5
4
COMMAND
3
2
1
OUTPUT MODE
0
binary
/ BCD
Output Mode
Counting Mode
Command-ID
000 = one-shot level 0 = binary
00 = Latch
001 = retriggerable
1 = BCD
01 = LSB r/w
010 = rate-generator
10 = MSB r/w
11 = LSB-MSB r/w 011 = square-wave
100 = software strobe
101 = hardware strobe
Commands are sent to the 8254 via io/port 0x43
Programming a PIT channel
• Step 1: send command to PIT (port 0x43)
• Step 2: read or write the channel’s Latch
– via port 0x40 for channel 0
– via port 0x41 for channel 1
– via port 0x42 for channel 2
Status/control (via port 0x61)
7
R/O
6
5
4
3
2
1
0
R/O
R/O
R/O
R/W
R/W
R/W
R/W
memory
parity
check
i/o channel
check
OUT2
1 = on
0 = off
i/o channel
speaker
check
1 = on
enable
OUT1
memory 0 = off
1 = on
parity
0 = off
check
enable
GATE2
1 = on
0 = off
Algorithm for 10-ms delay
• Step 1: turn off Channel 2 counting (and
disable PC speaker) by clearing bits #0
and #1 at i/o port 0x61 (called ‘PORT_B’)
• Step 2: issue command to 8254 to accept
a new value in Channel 2 Latch Register,
by outputing 10110000b to io-port 0x43:
i.e., chn2, r/w LSB/MSB, one-shot, binary
Algorithm (continued)
• Step 3: compute the frequency-divisor for
a ten millisecond delay (one hundredth of
one second) by dividing CLK2 frequency
(1,193,182 Hz) by one-hundred
• Step 4: write quotient’s LSB, followed by
its MSB, to channel 2 Latch (io-port 0x42)
Algorithm (continued again)
• Begin the Channel 2 countdown (set bit #0
at io-port 0x61) and immediately read and
save the Pentium’s TimeStamp Counter
• Spin in a tight loop until the OUT2 signal
goes active (Channel 2 count exhausted)
by testing bit #5 at io-port 0x61
• Immediately re-read TimeStamp Counter
• Perform subtraction (to get CPU cycles)
Algorithm (concluded)
• Divide cycle-count by ten-thousand, to get
processor’s clock-speed in Mega-Hertz
(i.e., in millions of cycles-per-second)
• Display this quotient in decimal format!
In-class exercise
• The Real-Time Clock chip automatically
updates its clock/calendar registers once
each second
• Register values cannot be reliably read
while the RTC’s update is in progress
• Most significant bit in RTC register 0x0A
provides indication of ‘update-in-progress’
• How long does the RTC ‘update’ last?
Algorithm for update-duration
•
•
•
•
•
•
•
Wait until a new RTC update begins
Immediately read the TimeStamp Counter
Wait until this update-operation finishes
Immediately read the TimeStamp Counter
Wait until the next update begins
Immediately read the TimeStamp Counter
The RATIO of these two time-intervals gives
‘update-duration’ as a fraction of one second