Transcript Chapter 18 Direct Current Circuits Sources of emf  The source that maintains the current in a closed circuit is called a source of.

Chapter 18
Direct Current Circuits
Sources of emf

The source that maintains the current in
a closed circuit is called a source of emf



Any devices that increase the potential
energy of charges circulating in circuits are
sources of emf
Examples include batteries and generators
SI units are Volts

The emf is the work done per unit charge
emf and Internal
Resistance


A real battery has
some internal
resistance
Therefore, the
terminal voltage
is not equal to the
emf
More About Internal
Resistance




The schematic shows
the internal
resistance, r
The terminal voltage
is V = Vb-Va
V =  – Ir
For the entire circuit,
 = IR + Ir
Internal Resistance and
emf, cont

 is equal to the terminal voltage
when the current is zero



Also called the open-circuit voltage
R is called the load resistance
The current depends on both the
resistance external to the battery
and the internal resistance
Internal Resistance and
emf, final

When R >> r, r can be ignored


Generally assumed in problems
Power relationship

I
 = I2 R + I2 r

When R >> r, most of the
power delivered by the battery
is transferred to the load
resistor
Resistors in Series



When two or more resistors are
connected end-to-end, they are said to
be in series
The current is the same in all resistors
because any charge that flows through
one resistor flows through the other
The sum of the potential differences
across the resistors is equal to the total
potential difference across the
combination
Resistors in Series, cont

Potentials add



V = IR1 + IR2 = I
(R1+R2)
Consequence of
Conservation of
Energy
The equivalent
resistance has the
effect on the circuit
as the original
combination of
resistors
Equivalent Resistance –
Series


Req = R1 + R2 + R3 + …
The equivalent resistance of a
series combination of resistors
is the algebraic sum of the
individual resistances and is
always greater than any of the
individual resistors
Equivalent Resistance –
Series: An Example

Four resistors are replaced with their
equivalent resistance
Resistors in Parallel


The potential difference across each
resistor is the same because each is
connected directly across the battery
terminals
The current, I, that enters a point must
be equal to the total current leaving
that point



I = I1 + I2
The currents are generally not the same
Consequence of Conservation of Charge
Equivalent Resistance –
Parallel, Example


Equivalent resistance replaces the two original
resistances
Household circuits are wired so the electrical
devices are connected in parallel

Circuit breakers may be used in series with other
circuit elements for safety purposes
Equivalent Resistance –
Parallel

Equivalent Resistance
1
1
1
1




Req R1 R2 R3

The inverse of the
equivalent resistance of
two or more resistors
connected in parallel is
the algebraic sum of
the inverses of the
individual resistance

The equivalent is always
less than the smallest
resistor in the group
Equivalent
Resistance –
Complex
Circuit
Gustav Kirchhoff



1824 – 1887
Invented
spectroscopy with
Robert Bunsen
Formulated rules
about radiation
Kirchhoff’s Rules


There are ways in which resistors
can be connected so that the
circuits formed cannot be reduced
to a single equivalent resistor
Two rules, called Kirchhoff’s Rules
can be used instead
Statement of Kirchhoff’s
Rules

Junction Rule

The sum of the currents entering any
junction must equal the sum of the currents
leaving that junction


A statement of Conservation of Charge
Loop Rule

The sum of the potential differences across
all the elements around any closed circuit
loop must be zero

A statement of Conservation of Energy
More About the Junction
Rule



I1 = I2 + I3
From
Conservation of
Charge
Diagram b shows
a mechanical
analog
Setting Up Kirchhoff’s
Rules

Assign symbols and directions to the
currents in all branches of the circuit


If a direction is chosen incorrectly, the
resulting answer will be negative, but the
magnitude will be correct
When applying the loop rule, choose a
direction for transversing the loop

Record voltage drops and rises as they
occur
More About the Loop Rule



Traveling around the loop
from a to b
In a, the resistor is
transversed in the
direction of the current,
the potential across the
resistor is –IR
In b, the resistor is
transversed in the
direction opposite of the
current, the potential
across the resistor is +IR
Loop Rule, final


In c, the source of emf
is transversed in the
direction of the emf
(from – to +), the
change in the electric
potential is + 
In d, the source of emf
is transversed in the
direction opposite of
the emf (from + to -),
the change in the
electric potential is - 
Junction Equations from
Kirchhoff’s Rules

Use the junction rule as often as
needed, so long as, each time you write
an equation, you include in it a current
that has not been used in a previous
junction rule equation

In general, the number of times the
junction rule can be used is one fewer than
the number of junction points in the circuit
Loop Equations from
Kirchhoff’s Rules


The loop rule can be used as often
as needed so long as a new circuit
element (resistor or battery) or a
new current appears in each new
equation
You need as many independent
equations as you have unknowns
Problem-Solving Strategy
– Kirchhoff’s Rules






Draw the circuit diagram and assign labels
and symbols to all known and unknown
quantities
Assign directions to the currents.
Apply the junction rule to any junction in
the circuit
Apply the loop rule to as many loops as
are needed to solve for the unknowns
Solve the equations simultaneously for the
unknown quantities
Check your answers
RC Circuits




A direct current circuit may contain
capacitors and resistors, the current will
vary with time
When the circuit is completed, the
capacitor starts to charge
The capacitor continues to charge until
it reaches its maximum charge (Q = C)
Once the capacitor is fully charged, the
current in the circuit is zero
Charging Capacitor in an
RC Circuit

The charge on the
capacitor varies with
time



q = Q(1 – e-t/RC)
The time constant,
=RC
The time constant
represents the time
required for the
charge to increase
from zero to 63.2%
of its maximum
Notes on Time Constant



In a circuit with a large time
constant, the capacitor charges
very slowly
The capacitor charges very quickly
if there is a small time constant
After t = 10 , the capacitor is over
99.99% charged
Discharging Capacitor in
an RC Circuit

When a charged
capacitor is placed in
the circuit, it can be
discharged



q = Qe-t/RC
The charge decreases
exponentially
At t =  = RC, the
charge decreases to
0.368 Qmax

In other words, in one
time constant, the
capacitor loses 63.2% of
its initial charge
Household Circuits



The utility company
distributes electric
power to individual
houses with a pair of
wires
Electrical devices in
the house are
connected in parallel
with those wires
The potential
difference between
the wires is about
120V
Household Circuits, cont.




A meter and a circuit breaker are
connected in series with the wire
entering the house
Wires and circuit breakers are selected
to meet the demands of the circuit
If the current exceeds the rating of the
circuit breaker, the breaker acts as a
switch and opens the circuit
Household circuits actually use
alternating current and voltage
Electrical Safety



Electric shock can result in fatal burns
Electric shock can cause the muscles of
vital organs (such as the heart) to
malfunction
The degree of damage depends on



the magnitude of the current
the length of time it acts
the part of the body through which it passes
Effects of Various Currents

5 mA or less



10 mA



Can cause a sensation of shock
Generally little or no damage
Hand muscles contract
May be unable to let go a of live wire
100 mA

If passes through the body for just a few
seconds, can be fatal
Ground Wire


Electrical
equipment
manufacturers
use electrical
cords that have a
third wire, called
a case ground
Prevents shocks
Ground Fault Interrupts
(GFI)





Special power outlets
Used in hazardous areas
Designed to protect people from
electrical shock
Senses currents (of about 5 mA or
greater) leaking to ground
Shuts off the current when above
this level