MICE Fiber Tracker Electronics AFE II Status First board under test!! MICE Fiber Tracker Electronics First AFE II Prototype Basic electrical tests Everything looks good.

Download Report

Transcript MICE Fiber Tracker Electronics AFE II Status First board under test!! MICE Fiber Tracker Electronics First AFE II Prototype Basic electrical tests Everything looks good.

MICE Fiber Tracker Electronics
AFE II Status
First board under test!!
MICE Fiber Tracker Electronics
First AFE II Prototype
Basic electrical tests
Everything looks good so far except for a few components that
were installed improperly
Functional tests begun
Downloads –OK
On-board processor –OK
Coming Alive!
First Problem discovered
Will require “green” wire fix
3 boards have been loaded
18 additional boards in the queue
Waiting for first results before giving the stuffing house the goahead to stuff the remaining boards
AFE II(t) operation in MICE
MICE Fiber Tracker Electronics
AFEII for MICE
Recall:
AFEs mount on ether side of the VLPC cass,
with fibers going to the VLPCs between them.
AFE has 8 identical modules
Each module reads 64ch of VLPCs
AFEs functions: fast discr (1bit/ch) send to L1
trigger system. If the event looks interesting
(to the L1 system!), the AFE can “remember” Q
from ~4uS earlier and digitize it for readout
• Much slower than the discriminators!
MICE Fiber Tracker Electronics
AFEII for MICE
Digital readout vs. Analog readout
AFEII two readout paths
Digital:
Discriminators go over LVDS links
• More details later
Analog:
Zero suppressed data from ADCs
(addr/data pairs) over a custom parallel link
(a.k.a. gray cable)
• More details later
MICE Fiber Tracker Electronics
AFEII for MICE
AFEII designed for Tevatron not MICE!
AFEII two readout paths:
• L1: 512 discriminator bits/board/132ns
• L2: (only after an “L1 accept”) reads out ADC
8bits/ch x 512ch (zero supressed)
• AFEII designed for ~10Khz L1 accept rate
at ~5% deadtime => 10uS per event time budget
MICE Fiber Tracker Electronics
AFEII for MICE
Fiber tracker: why analog at all?
Better quality data
•
•
•
•
ADCs data can be corrected for common mode
ADCs can correct for ch-to-ch variation
But watch out for zero supression!
For Dzero, can use to improve resolution
MICE Fiber Tracker Electronics
AFEII for MICE
Digital readout details:
LVDS here means a specific chip set from TI
SN65LVDS95 (running @ 53Mhz)
• 20 bits + 1 “frame” bit sent over 4 UTP pairs
(3 signal + clock) @ 53 * 7 = 371 Mhz
• Frame bit sent once every 7 * 18.8ns = 132ns
4 LVDS links/board = 1/pair of modules
(10bits per module)
Data rate = 53Mhz * 20 * 4 = 4.24 Gbps
MICE Fiber Tracker Electronics
AFEII for MICE
Analog readout details:
Custom bi-directional parallel link between the
Sequencer and the AFE
8 data bits + data valid per AFE
Max data rate = 53 * 8 = 424 Mbps
Digitization:
2 dual ADCs/64 ch module=16 ch/ADC
ADC runs @ max 10Mhz => 16 * 100ns = 1.6uS
Tot: ~2us + ~40ns / hit ch= ~21us max
MICE Fiber Tracker Electronics
AFEII for MICE
Mice beam structure
~600 muons in 850 uS
us
Long enough between pulses =  for DAQ
Analog readout: depends on occupancy
• If FULL readout, can do about ~40 during spill
Digital readout: can keep up
• Still not 100% live time: need resets
MICE Fiber Tracker Electronics
AFEII for MICE
Mice readout
Analog readout for MICE
Two options:
1. the full Dzero system
-Sequncer (SEQ) and sequencer controller (SEQC)
(and crate! 9U custom backplane…)
- VME Receiver Buffer (VRB) and VRB controller
(VRBC) (and another 9U crate!)
- must talk to SEQ/SEQC/VRB/VRBC so need
1553 interface as well
MICE Fiber Tracker Electronics
AFEII for MICE
Mice readout (cont.)
Analog readout for MICE
Two options:
2. the StandAlone Sequencer (SASeq)
+used in the MICE cosmic test
-rather slow…
MICE Fiber Tracker Electronics
AFEII for MICE
Analog readout for MICE
+ tons of experience from Dzero
+ AFEII designed to work this way
+ know how to trigger, sync board to board, etc.
- need time to digitize!
~ maybe beam structure can be chosen to make
this mode work better?
600mu/1ms => 600KHz L1 accept rate!
MICE Fiber Tracker Electronics
AFEII for MICE
Mice readout
Digital readout for MICE
+ fast
+ very simple
- need a receiver… more detail below
- no detailed analog info
~ not for use with AFEII-t (not a problem!)
MICE Fiber Tracker Electronics
AFEII for MICE
Digital readout for MICE
Need a new board!
• Receive LVDS, store into FIFO, interface to VME
But
• How to get clock to boards?
• How to get trigger to board?
Can still use the gray cable! (w/SASeq)
MICE Fiber Tracker Electronics
AFEII for MICE
Need new board
Very simple 6U VME
Should be easy to design and build!
Cost=$1K/board
SRAM
1 board/AFE
VME I/F
FPGA
LVDS
MICE Fiber Tracker Electronics
AFEII for MICE
Hybrid option
On the AFEII, there is a path from
FPGA to LVDS
Can readout analog information via LVDS
Still need the digitize time =~1.6 to 2 us
But can readout as fast as digitize
MICE Fiber Tracker Electronics
AFEII for MICE summary
Analog readout
Maybe 40 events/pulse (if 850uS pulse!)
Digital readout
Trade live time vs. overlaps (2K events/pulse)
• Min integration window ~50ns, max=anything!
• Reset time ~40ns
Need to design and build a new board!
Not really an option for MICE since MICE will use AFE
IIt
• Time stamp for hits – TAC – need analog output
Hybrid readout
ADC thru LVDS (400 events/pulse)
Still need the new board!
MICE Fiber Tracker Electronics
AFE II for MICE
D0 is starting work on an ADC  LVDS
interface board
This will likely work for MICE and be the
preferred readout
Data rates exceeding 600 muons/sec are
therefore possible with 3 Hz RF
3 Hz is appears to be doable and for DAQ
considerations is preferred over 1 Hz
operation