Drafting 1 Final Exam Review Notes The thin lines placed between extension lines to indicate a linear distance are ____ lines. a. b. c. d. Cutting Plane Dimension Object Section The centers of.
Download ReportTranscript Drafting 1 Final Exam Review Notes The thin lines placed between extension lines to indicate a linear distance are ____ lines. a. b. c. d. Cutting Plane Dimension Object Section The centers of.
Drafting 1
Final Exam Review Notes
The thin lines placed between extension lines to indicate a linear distance are ____ lines.
a.
b.
c.
d.
Cutting Plane Dimension Object Section
The centers of round objects are indicated using ____.
a.
b.
c.
d.
Centerlines Hidden Lines Object Lines Section Lines
General classifications of materials are identified using ____.
a.
b.
c.
d.
Centerlines Hidden Lines Object Lines Section Lines
Section lines are typically drawn inclined at ____.
a.
b.
c.
d.
30 degrees 45 degrees 60 degrees 75 degrees
Cutting-plane lines are drawn to the same weight as ____.
a.
b.
c.
d.
Centerlines Hidden Lines Object Lines Section Lines
Which of the following tools should not be used to sketch lines?
a.
b.
c.
d.
Drawing Pencil Eraser Graph Paper Scale
A(n) ____ is sketched by first constructing a rectangle with dimensions equal to the major and minor axes of the object.
a.
b.
c.
d.
Circle Ellipse Hexagon Octagon
A(n) ____ is sketched by first constructing centerline axes and inclined lines at 30° and 60°.
a.
b.
c.
d.
Circle Ellipse Hexagon Octagon
A ____ is used to draw circles.
A.
B.
C.
D.
Compass Protractor Scale Triangle
Which of the following tools is used to transfer distances?
a.
b.
c.
d.
Dividers French Curve Protractor Template
A ____ can be used as a pencil pointer.
a.
b.
c.
d.
Compass Drafting Machine Sandpaper Pad Template
A ____ is used to remove eraser dust from a drawing.
a.
b.
c.
d.
Drafting Machine Dusting Brush Lead Holder Scale
A(n) ____ is used to mask items you wish to keep when erasing errors from a drawing.
a.
b.
c.
d.
Dusting Brush Erasing Shield Irregular Curve Protractor
A drawing sheet should be fastened to a drawing board using ____.
a.
b.
c.
d.
Drafting Tape Glue Staples Tacks
A ____ is used to draw inclined lines that cannot be drawn with triangles.
a.
b.
c.
d.
Compass Protractor Scale T-Square
Which of the following is not a form of drafting media?
a.
b.
c.
d.
Drafting Film Drafting Tape Tracing Paper Vellum
The dimensions of a B-size sheet are ____.
a.
b.
c.
d.
8.5 x 11 11 x 17 17 x 22 22 x34
A(n) ____ scale typically contains scales labeled 10, 20, 30, 40, 50, and 60.
a.
b.
c.
d.
Architect’s Engineer’s Mechanical Drafter’s Metric
Which of the following is not a computer input device?
a.
b.
c.
d.
Digitizing Tablet Keyboard Mouse Plotter
The best way to attach drafting media to a drawing board is to use ____.
a.
b.
c.
d.
Staples Thumbtacks Rubber Cement Drafting Tape
The whole number divisions on an architect’s scale represent ____.
a.
b.
c.
d.
Inches Feet Millimeters Meters
____ are drawn approximately twice as thick as hidden lines.
a.
b.
c.
d.
Centerlines Extension Lines Object Lines Section Lines
____ have alternating long and short dashes drawn through the perimeter of a circular object.
a.
b.
c.
d.
Centerlines Extension Lines Object Lines Section Lines
On an architect’s scale, each division on the 16 scale is equal to ____.
a.
b.
c.
d.
½” ¼” 1/8” 1/16”
The lines making up the sides of a hexagon form ____ angles.
a.
b.
c.
d.
30 degrees 60 degrees 90 degrees 120 degrees
A(n) ____ is a closed curve in the form of a symmetrical oval with four quadrants.
a.
b.
c.
d.
Ellipse Octagon Rhomboid Trapezoid
A line that forms a 90° angle with another line is ____.
a.
b.
c.
d.
Concentric Parallel Perpendicular Tangent
A regular ____ has five equal sides.
a.
b.
c.
d.
Hexagon Octagon Pentagon Rhomboid
A(n) ____ triangle has no equal sides or angles.
a.
b.
c.
d.
Equilateral Isosceles Right Scalene
Which of the following is not true with respect to lettering?
a.
b.
c.
d.
Single-stroke Gothic characters are the recommended standard.
Vertical and inclined lettering should not be used on the same drawing.
All letters should be drawn to a different line weight than the object line weight.
Lettering should be made with a drafting grade pencil.
The horizontal spacing between words and sentences should be ____.
a.
b.
c.
d.
Half the letter height.
Equal to the letter height.
Twice the letter height.
Three times the letter height.
A lettering height of ____ is most commonly used on drawings.
a.
b.
c.
d.
1/8” ¼” ½” ¾”
A(n) ____ is operated by guiding a stylus through cuts in a template to place lettering.
a.
b.
c.
d.
Ames lettering guide Braddock lettering triangle Burnishing tool Leroy lettering instrument
Letters on drawings should be drawn to the ____ line weight.
a.
b.
c.
d.
Border Hidden Object Section
In orthographic projection, the ____ principal plane represents the projection of the top view of the object.
a.
b.
c.
d.
Frontal Horizontal Profile Vertical
____ projection is the orthographic projection method most commonly used in the United States.
a.
b.
c.
d.
First-angle Second-angle Third-angle Fourth-angle
When locating views on a drawing, the top view should be placed ____ the front view.
a.
b.
c.
d.
Above Below To the left of To the right of
When projecting views, depth distances may be projected to side views with a ____ projection angle or a compass.
a.
b.
c.
d.
30 degree 45 degree 60 degree 75 degree
General-purpose section lines are typically spaced ____ apart.
a.
b.
c.
d.
1/8” ¼” ½” ¾”
A(n) ____ is developed by passing a “stepped” cutting plane through features that do not lie on the same a.
b.
c.
d.
Full section Offset section Removed section Revolved section
A(n) ____ is developed by cutting out a portion of a long, uniform object and sliding the ends together.
a.
b.
c.
d.
Aligned section Conventional break Offset section Removed section
To show where an imaginary cut is made through an object to be sectioned, a(n) ____ line is used.
a.
b.
c.
d.
Cutting-plane Object Phantom Section
General-purpose section lines are usually drawn at ____ angles.
a.
b.
c.
d.
15 degrees 30 degrees 45 degrees 60 degrees
A(n) ____ section is used to describe objects with irregular features by rotating the features that do not intersect the cutting plane into the same plane.
a.
b.
c.
d.
Aligned Broken-out Outline removed
A cabinet oblique drawing has a depth axis drawn at ____ scale.
a.
One-quarter b.
c.
d.
One-half Three-quarter Full
Which of the following statements is not true in relation to dimensioning pictorial drawings?
a.
b.
c.
d.
Dimension lines are drawn parallel to the direction of measurement.
Dimensions on adjacent planes can use the same extension line.
Dimension numerals and letters may be unidirectional or parallel to the pictorial planes.
Dimensions should be given at a scaled size rather than full scale.
A(n) ____ drawing uses two 30° horizontal axes and a vertical axis to represent the basic dimensions of an object.
a.
b.
c.
d.
Isometric Multiview Orthographic Section
The depth axis lines in a cavalier oblique drawing are drawn at ____ scale.
a.
b.
c.
d.
¼ ½ ¾ Full
The depth axis lines in a cabinet oblique drawing are drawn at ____ scale.
a.
b.
c.
d.
¼ ½ ¾ Full
In an oblique drawing, the ____ surface of the object is parallel to the projection plane.
a.
b.
c.
d.
Front Side Top Bottom
Which of the following is true of dimensions in pictorial drawings?
a.
b.
c.
d.
They are placed on top of (within) the view.
They are placed in pictorial planes.
They are duplicated across the views to help clarify the content.
They are drawn for hidden features.
A two-point perspective drawing is also known as a(n) ____ perspective.
a.
b.
c.
d.
Angular Horizontal Parallel Vertical
Exploded assembly drawings are commonly drawn as ____ drawings.
a.
b.
c.
d.
Isometric Multiview Oblique Perspective
A is
French Curve
B is 45 Degree Triangle
C is
30-60 Degree Triangle
D is
T-Square
E is Drawing Board
F is Erasing Shield
G is
Pencil
H is
Proctractor
I is Dusting Brush
J is Pencil Pointer
K is
Eraser
L is Compass
M is
Drafting Tape
N is
Scale
A is
Section Lines
B is Phantom line
C is
Dimension line
E is Object Line
F is Border Line
G is
Cutting-Plane Line
H is