Transcript 007_HYTO - Hytorc

UBC International Training Fund
Presents
1
Hytorc Tools
The following material is intended to make you aware
of the currently acceptable and recognized methods of
performing the tasks described in this presentation.
However, every possible application of these methods
cannot be foreseen and the following material is not
designed to cover every potential application. Therefore,
you must always follow all current procedures and safety
regulations whenever you perform any of the tasks
discussed in this presentation.
We Have Looked At A Lot Of
Ways To Tighten A Bolt
Torque Is Right For 90%+ Of All Bolts
4
(HYTORC TRAINING VIDEO)
11 MINUTES
5
HYTORC MXT SERIES
•Unibody housing
•3000+ft/lbs per lb. of weight
•360 x 180 hose swivel
•3% accuracy
•anti-backlash pawl
•square and hex drives
•60 position reaction arm
6
HYTORC BLITZ SERIES
NARROW CLEARANCE
PROTRUDING STUDS
CONVERTIBLE
7
Accessories For Virtually All Special Applications
8
SIMULTORC -
MULTIPLE TOOLS:
FASTER RESULTS
ABSOLUTELY EVEN LOAD
PARALLEL CLOSURE
9
SIMULTORC -
Torque Just Doesn’t Get
Any Better Than This!
10
BUT..
What If You Could Combine All The
Benefits Of Torque
FAST
EVEN
EASY
With All The Advantages Of
Tensioning?
•NO REACTION POINT
•NO UNWANTED FORCES
•NO GALLING - EVER
•LOAD ACCURATE TO 1%
11
HYTORC has found the way…
..and bolting will never be the same!!
12
NOT ONLY HAS HYTORC COMPLETELY
REDESIGNED THE TOOLS…
•CONTINUOUS ADVANCE
• 3 TIMES FASTER
XXI
STEALTH
13
THE SECRET IS IN THE DISC©
14
THE HYTORC DISC IS A…
•UNIQUE THREADED WASHER
•USED WITH SPECIAL
LOW- RADIUS NUT
15
A Custom Designed Drive Socket Holds On The Disc Washer
And Turns The Nut
Without An External Reaction Point!
16
HOW IT WORKS..
•The Threaded Segment In The Disc Acts Like
A Jam-nut Holding The Stud From Turning
•The Nut Is Tightened And The Threaded
Segment Is Drawn Upward With The Stud
As It Is Stretched To The Desired Tension
•All Of This Is Done In The Same Height
And Footprint As A Standard Nut
•The Disc And The Nut Stay In Place
Until Removed
•Replace The Disc And Re-use The Nut
17
THE RESULTS..
•
•
•
•
•
•
No Reaction Point Needed
No Torsion In The Stud
No Backup Wrench
No Unsafe Pinch Points
No Stud Galling
No Unwanted Bending
Forces
18
NARROW CLEARANCE?
NO PROBLEM!
SIMULTORC + THE NEW
HYTORC DISC=
NEAR BOLTING
PERFECTION
19
Let’s Take A Moment To See How
The Hytorc Disc System
Compares With Standard
Torquing Methods
20
HYTORC STILL HAS ONE MORE
CARD TO PLAY!!
• As Near Perfect As The Disc System Is It
Still Relies On Turning Against The
Threads Of The Existing Stud
• This Can Result In Less-than-perfect
Friction Conditions And Is Theoretically
Subject To Damage
21
When The Results Absolutely Must Be Perfect
Here Is The Ultimate Answer -
22
Revolutionary 3 Part
“Nut-within-a-Nut” Design
23
As The Outer Nut Turns It
Draws The Inner Nut And The
Stud Up, Stretching The Stud
24
Driven By A Hytorc Wrench Just As If Torquing But
It Never Turns Against The Threads Of The Stud
•No Reaction Point (Reacts Within Itself)
•No Backup Wrench Needed (No Torsion)
•No Overstretching (And No Tommy-bars)
• ABSOLUTE PRECISION – and Its FAST!!!
25
Combine The Hytorc Clamp Nut With
Multiple Tools And You Have, Very Simply...
As Close As Can Be To
Bolting Perfection!
26
SUMMARY OF OUR COURSE OBJECTIVES:
1. Elements Of Bolting Theory
•Bolt Is A Spring
•Pre-load Or Tension
Holds Joint Together
•Torque Is A Means To Get Tension
27
2. Advantages And Disadvantages Of
Various Bolting Methods On Common
Bolting Problems
•Many Factors Affect Torque Values
•Bolting Must Be “Right” Not Just “Tight”
•Direct Tensioning Is Great In Theory
But Difficult To Achieve In The Real
World With Most Methods And Tools
28
3.
Gaskets Are Often Necessary To Obtain A Seal In A
Bolted Joint
•
There Are Many Types Of Gaskets And Gasket
Materials And The Selection Of The Proper
Combination Is Critical To Getting And
Maintaining A Seal
4. Special Applications Such As Swaged Tube Fittings
Require Specialized Tools Which Are Available
29
6.
Certain Applications Require The Correct Installation Of
Locking Devices As A Safeguard Against Bolts And
Nuts Backing Off And Losing Their Tension
7.
There Is No Longer A Need To Choose Between The
Advantages Of Torque And The Advantages Of
Tensioning. You Can Have Both!
30
Finally,
We Promised You Hands On Time
Not Just Talk!!
So Once Again...
31
GOD BLESS AMERICA
32
The End