Transcript Sales Reference Guide - Bosch Security Systems

Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Recipient
RSO EMEA (Gerard Otterspeer, Harold Van den Oetelaar), RSO
AMEC (Steve Tangert; Chris Johnston; Willem Ryan), RSO APR
(Jeffrey Law), RSO China (Leo Chen)
Cc
Topic
Bosch VMS Sales Guide
1 Background
This document summarizes the Bosch VMS and BVIP design specifications, and is a guide to
planning a Bosch VMS system with Bosch cameras and storage. It focuses on Bosch VMS with
VRM.
This document is subject to change. Once a new version is published, earlier versions are void.
2 Design Specifications
This document lists the valid design specifications for version 4.5.x You require an updated version of this document to commission sales for a more recent version of Bosch VMS.
2.1 Datasheet facts
Subject
Management Server (MS)
Management Servers
1
Encoder inputs, cameras and
decoders summarized
Enterprise User Groups/ User Groups
User Groups
2.000
Workstations connected in
parallel
Decoders in total
IntuiKey Keyboards connected to decoder
Keyboards connected to
workstations (IntuiKey or
n.a.
20 with overall max 1000 users
100
128
60
1 per workstation, hence 100
in total
Enterprise Management
Server
10 per Enterprise User group
30 per Enterprise User group,
if each MS < 100 channels.
10.000 per Enterprise User
group
20 with overall max. 1000 users
Same as MS
100
Same as MS
No Enterprise functionality.
Per Management Server only
100
Page 1 of 8
Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide
Videotec DCZ)
Logbook
VRM
For legacy with H.263 only:
Primary NVR / Backup NVR
For legacy with H.263 only:
Failover NVR
DiBos / BRS
DVR (400, 600, 700)
POS/ATM
Virtual Inputs
AMG
Task Schedules
Compound Events
Special Days
Export ASF
Export
Maps
Allegiant CCL commands
Mobile Video Service (MVS –
Web Client / IOS Client)
4GB (6 Million Entries)
Tested with 40
4 max.
Same as MS
Same as MS
Same as MS
4
Same as MS
Tested with 100
15
15
4.000 (limited in configuration)
16 with max. 50 cameos per
AMG (limited in configuration),
while maximum of 128 decoder in overall system
200 (limited in configuration)
1000, up to 10 devices per
compound event
24
“1 minute of exporting ASF (4
cameras) takes 1 minute”
Max 4 cameras in parallel
40 maps maximum
Max 10/sec
20 connections per MVS.
(1 connection per device
1 connection per cameo).
E.g. 5 Ipads with quadview:
5x4=20 connections.
1000
Same as MS
Same as MS
Same as MS
No Enterprise functionality.
On Management Server only
Same as MS
Same as MS
Same as MS
Same as MS
Same as MS
Same as MS
Same as MS
No Enterprise functionality with
remote access. Should be
used in the same LAN.
2.2 System facts




WIN7 SP1 (64) & Server 2008 R2 requested
o Exception: NVR
Enterprise Management Server requests 4 GB RAM
Op-Client with Enterprise capabilities requests 4 GB RAM (8 GB recommended!)
All IP devices must be associated to 1 Management Server. IP devices must not be
shared between multiple Management Servers
Page 2 of 8
Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide


IP-Cameras, -Encoders and -Decoders must not be shared with other systems. For
temporary migration reasons VIDOS and BRS can stream video from IP cameras or encoders in parallel to BVMS, but be aware of overloading the encoder
Bosch VMS does not support connection to BVIP devices through HTTP, HTTPS, or
other encrypted connections (e.g. AES). Changing the rcp+ port is also not supported.
2.3 Remote access

Bosch VMS 4.5 supports connection across Wide Area Network (remote access) from
an Operator Client to a Management Server and all devices managed by it.
o
o
o

Devices and Management Server have to be in the same Local Area Network
(LAN)
Minimum bandwidth required within that LAN are 100Mbit/s
 Remote access of devices to the Management Server are not supported
Minimum bandwidth required between remote site and local site is 300 Kbit/s
Transcoded video
o Enables to BVMS OC to operate within low bandwidth (>=300 kbit/s) networks
o Transcoder is available for Live and Playback for VRM connected BVIP cameras.
o If no transcoder sessions or transcoder HW is available on the VRM no image
will be displayed in OC.
o Transcoded videos are selected by Operator per device.
Page 3 of 8
Security Systems
From
Our Reference
Tel
Fax
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide
Transcoded video is indicated by an icon in cameo.
Bosch VMS supports the transcoder service within the internal transcoder of the
VRM installed on DIVAR IP 3000/7000 as well as DIVAR IP 2000/6000.
In addition the external transcoder VJT-XTC XF is supported as well
Transcoding services are managed by VRM
 Not configurable or shown in BVMS
Following operations are not supported by transcoded video
 Delete Video
 Protect/Unprotect Video
 Authenticate Video
 Export Video
 Forensic Search
o
o
o
o
o
2.4 Limiting facts


Enterprise Management System
o Analog Monitor Group is not supported across different Management Servers
o Monitor Wall:
 Cameras of subsystems can be connected to monitor wall configured in
Enterprise Management Server only
 No pre-configuration of sequences with cameras from subsystems
o Remote cameras or cameras using transcoded streams are not supported on
monitor wallBIS - BVMS connectivity is not supported across different Management Server
o Mobile Video Service (Web Client / IOS Client) is not supported across different
Management Server
o Map does not indicate cameras of different Management Servers on one map
Monitor Wall:
Assign
Usage
AMG
Display pre-
Usage in
via
Local
Enterprise
D&D
Keyboard
Keyboard incl.
by
on
configured
OC
OC
in OC
incl. PTZ
PTZ
SDK
Alarms
Sequences
yes
Monitor Wall yes


Display
Control by
Control by
Workstation Decoder/Server Control Camera
in
Display au- Support
tomatic
more
Sequences Layouts
no
yes
yes
yes
yes
yes
yes
yes
no
yes
yes
no
no
no
no
yes
no
yes
NVRs:
o Bosch VMS NVR and VIDOS NVR do not support
 H.264
 HD resolution
 Forensic Search
 Windows 7 / Server 2008
Page 4 of 8
Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide

Devices & HW
o Status from Satellite Allegiant cameras and VIDOS NVR will not be displayed
o H.264 BP of TI based MPEG4 devices is not supported
o B-Frames are not supported
o Backup VRM, Backup LUN is not supported
o VIPXD decoders do not support H.264 MP
o VIPXD decoders do support H.264 BP+, which however must be limited to
1200Kbps for ARM based devices, and 2500Kbps for XFM4 devices
o Bosch VMS and BVIP components are tested on Bosch hardware. You can deploy a Bosch VMS system on 3rd party servers and workstations, following the
minimum requirements. For workstations you must use one of the recommended
graphic cards. For issues on servers and workstations which cannot be reproduced in tech support, we will ask you to reproduce the issue on Bosch hardware.
o DiBos and BRS are integrated into Bosch VMS as transceivers. I.e, both live and
playback video is streamed through DiBos/BRS. Therefore, you cannot show any
-DiBos/BRS image on a BVIP decoder like VIPXD.
2.5 Recording






ANR is supported only for a couple of seconds to buffer short network outages (see
separate Tech Note on ANR). In the case of new Starlight series, buffering time is considerably longer (> 1 min).
Bosch VMS supports multiple Pools (Pooling implemented in VRM 3.0)
o Migration from former VRM versions is possible
Direct iSCSI and Local Storage is supported for devices which support Firmware 4.x and
above. I.e. no Local Storage support for VIPX1/X2 and VJ800x.
VRM and Local Storage support recording
o Pre-Alarm, Alarm and Post-Alarm, while pre- and post- must be at least 15 seconds. I.e., pre-alarm is always streaming over the network
o Continuous, Alarm and Post-Alarm, while post must be at least 15 seconds
VRM/iSCSI and local recording do not support the configuration of Holidays for recording. Special Days must be used.
From VRM datasheet: One VRM supports:
o 2048 channels
o 1 PB storage (net capacity)
o 40 disk arrays (recommended)
o maximum 120 iSCSI targets supported
When planning for larger environments we strongly recommend using large sized disk
arrays instead of a large number of small disk arrays (vertical scaling instead of horizontal scaling). For systems with more than 40 disk arrays, please contact a Bosch Design
Engineer. iSCSI based storage systems not qualified by Bosch are not supported.”
Page 5 of 8
Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide

DIVAR
o BVMS 4.5 supports DVR 400/600 and 700
 DVR 431, 440, 451, 480
 DVR 630, 650, 670
 Divar 700
o Only DVR is licensed, not the cameras used on the DVR
o Needed license is: MBV-XDVR-45
o Supported DVR-Events:
 Disk Failure
(only DVR 400 & 600)
 Disk Full
(only DVR 400 & 600)
 Fan Failure
(only DVR 400 & 600)
 Temperature above limit
(only DVR 400 & 600)
 System alarm state
(only DVR 400 & 600)
 Software Incompatibility
(only DVR 400 & 600)
 DVR DataInput
(only DVR 700)
o Supported Archive Operations
 Delete Video
(only Divar 700)
 Export native and asf
(all Divars)
 Motion search
(all Divars)
 IVA overlays in cameo
(only Divar 700)
 No protect/unprotect
(all Divars)
 No instant playback
(all Divars)
 No playback in alarm cameo space (all Divars)
 No Video authentication
(all Divars)
o Divar is only supporting 5 connections:
 1 connection for events etc. from server
 1 connection per live cameo per camera
 1 connection for playback per camera
o No support for decoder connections
2.6 Mobile Video Service (Web Client / IOS Client)
o
o
o
o
o
Runs on iPad, iPhone and HTML 5 web-client (tested on Internet Explorer 9.0)
Supports live and playback simultaneously!
Supported IOS versions: 6.1.2 or earlier
Supported HW versions: iPad 2 and 3; iPhone 4 and 5
Supported cameras:
 IP cameras with H.264 support that are controlled by Bosch VMS
 (not controlled by VIDOS)
 ONVIF cameras
 BRS/DiBos H.264 cameras
Page 6 of 8
Security Systems
From
Our Reference
Tel
Fax
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide
2.7 ONVIF:
o
o
o
o
o
o
BVMS 4.5 supports ONVIF Profile S:
 ONVIF cameras are detected in network scan
 Life images of ONVIF cameras are shown
 Supports PTZ control
 Recording, playback and export is possible via Video Streaming Gateway
 In case ONVIF camera provides a second stream, this can be selected
for live view
State supervision and configuration of ONVIF cameras is not yet supported in
BVMS 4.5
For the max. no. of ONVIF cameras connected to a Video Streaming Gateway,
pls refer to the VSG datasheet.
VSG is currently only tested for Onvif cameras. Other formats (RCP+, RTSP,
JPEG...) are not yet tested with Bosch VMS.
ONVIF cameras do not work on Monitor Wall
ONVIF cameras are listed on the following webpage: www.onvif.org
The following ONVIF cameras were tested with Bosch VMS 4.5
Vendor
Axis
Axis
Axis
Axis
Axis
Sony
Sony
Camera
Model
M7014
P1347
P5534
Q1604
Q6035
CH240
CH280
Camera Type
4-channel NVT
fixed camera
PTZ
fixed Camera
PTZ
fixed camera
fixed camera
used FW
5.40.7.1
5.40.9.2
5.40.9.2
5.40.3.2
5.41.1
1.50
1.50
2.8 Calculations


Encoding of IP encoders and cameras is limited and must under no circumstances be
overloaded. To check if the required resolution, IPS and streaming values are achievable, check VRM calculation excel sheet.
Storage must be calculated taking iSCSI sessions, RAID levels and internal buffer into
consideration. In order to calculate the required storage for certain video bandwidth levels and retention times, use the VRM calculation excel sheet in its latest available version.
2.9 Further design information

For system examples please refer to Bosch VMS Blueprints
Page 7 of 8
Security Systems
From
Our Reference
Tel
ST-ESS/PRM
von Rosenstiel
+49 (0) 89 6290 1451
Fax
Grasbrunn
20.02.2014
Vs.4
Requirements specification
Bosch VMS Sales Guide


Bosch VMS requires an extension of the Software Maintenance Agreement after 1 year
of License Activation in SLMS. Without a valid SMA, the system is not covered by Technical Support and will not receive upgrades to future revisions.
Upgrading to 4.5 requires a valid SMA.
New purchases have one year of SMA included, hence activations after April 8th 2012
will still be able to upgrade.
Installations that activated before April 8th 2012 are required to extend the SMA.
2.10 Compatibility BVMS Rel. 4.5.5
Bosch VMS 4.5 has been tested with the following SW/FW versions:
Firmware MPEG-4: 4.15.02
Firmware CPP3: 5.70.0039
Firmware CPP4: 5.70.0039/5.80.73
Firmware CPP5: 5.70.0028
Firmware CPP-ENC 5.52.0015 (for VIP X16000 XFM4)
 Firmware CPP-ENC 5.60.0061 (for VJT XF family)
 Firmware X1/X2: 2.53.05
 Combined Firmware 5.80.0625 (CPP3, CPP4, CPP-ENC)
 VRM: 3.00.48
 VSG: 5.60.55
 BRS: 8.10/8.11
BIS: 3.0
iOS: 6.1.2
Allegiant MCS: 2.92.0.1
Intuikey Keyboard: 1.96
VMWare: 5.1.0
DVR 2.1 / 3.60
 VideoSDK: 5.61.42
Latest compatibility matrix will also be available at the IPP – Web-page:
http://ipp.boschsecurity.com/technology_partner_programm/03_toolkit/04_compatibility/02_content_page
_234
ST-ESS/PRM
Page 8 of 8