Transcript Residential Closet Install PP 12.07.

Installation Guidelines
Typical Walk-in Closet with elfa® décor
TOOLS REQUIRED FOR
elfa® INSTALLTION
BASE COMPONENTS FOR
AN elfa® SOLUTION
- Power drill with wood (1/8”) and
sheet rock (3/8”) bits, #2 Phillips head
bits
elfa® Top Track
- Level
- Hammer or Rubber Mallet
- Ladder
- Jig Saw or Sawz-all with bi-metal
blades to cut track, shelves and rods
to length
elfa® Anchors
elfa® Hanging
Standard
elfa® Ventilated
Bracket
-Tape Measure
- Refer to the Assembly and Install
Guide for specific instructions
elfa® Ventilated Shelf
A STEP-BY-STEP APPROACH TO AN
elfa® CLOSET INSTALLATION
The following photographs will allow you to view an entire installation
from start to finish. Without a doubt, the most important part of any elfa®
project is the correct installation of the elfa® Top Track. After all, the
entire system hangs from and depends on this important first step.
Marking the holes for drilling for the anchors
Requires making sure the top track is LEVEL.
-Place track at desired height
-Level
-Mark holes for drilling
A.
B.
C.
Hanging The elfa® Top Track
It is a good idea to determine what is on the
backside of the wall in order to ensure you do
not drill into pipes or wires.
A. Drill marked holes
B. Insert elfa anchors
C. Hang track, check with level
D. Tighten screws with power drill
IMPORTANT: Use power drill at low speed to firmly seat plastic
molly and to avoid stripping the screw heads. The anchor
must seat firmly to the back of the sheet rock.
D.
A.
B.
C.
D.
Placing The elfa® Standards and Brackets
This approach is quick and in most cases ensures that
you will not have to redo placement of brackets due to
incorrect placement.
A. Hang all standards needed to complete stretch
of wall and group together.
B.-D. Refer to your drawing and place brackets into
slots. Use a tape measure as shown, or count slots in
order to find precise placement.
E. Spread standards to specified widths or 2 ft. centers to
accommodate the ventilated shelves.
E.
Installing The elfa® Ventilated Shelf
• Ventilated Shelves have a top and a bottom - the middle
support wire is connected at the bottom of the shelf
• Install the Ventilated Shelves from shortest to longest,
regardless of their location in the space. This will help in
measuring.
• Lock the Shelf into place by pressing down on the middle
of the Shelf and pushing toward the wall. (Figure E)
To Remove A Shelf
• Hold the Hanging Standard steady with one hand. Place
the other hand at the back of the Shelf. Pull up and forward
on the shelf to release.
Installing The elfa® décor Fascia
A.
A. Position the Fascia with the opening facing the
ventilated shelf. The notch in the Fascia that hooks
onto the front support wires of the ventilated shelf
should be at the top. Hook over top wire with a
downward motion, secure it to the front of the shelf.
B.
B. Use the included clips to secure the Fascia to the
ventilated shelf – the top of the clip has a groove
that holds one shelf wire.
C. Once it is attached to the
underside of the shelf wire,
slide it all the way to the
front of the shelf and into the
opening of the Fascia for a
secure hold.
C.
Installing The elfa® décor Hanging
Drawers and Gliding Pant Racks
A. Install the U-Shaped Metal Glide – all
décor gliding components utilize the same UShaped Metal Glide. This piece has three
metal tabs and a metal knob on each side (on
the top) that locks the glide into the Bracket.
Begin with the left Bracket. Align the metal
tabs on the Glide with the cut-out notches of the
Bracket. When aligned, hold the front of the
bracket and press on the Glide at the back
rounded corner until you hear it lock into place –
then repeat on the right side.
B. To remove the glide, place one hand at the
back of the Glide, with your
thumb on the hanging standard,
gently push the glide forward
with your fingers. Insert and
twist a small flat head
screwdriver between the
Bracket and Glide – it should
pop out from the Bracket.
Installing The elfa® décor Hanging Drawers and Gliding Pant Racks
Install the Gliding Accessories
Align the rollers on each side of the frame with the openings in the U-Shaped
Metal Glide. Slide the wood frame into the glide.
Drawers
Always start with the bottom drawers and work up. Insert the Drawer in the frame opening
and attach it to the left and right side of the wood frame with the Drawer Clips provided.
If you would like more space between the drawers, just move them to the desired position.
elfa® Ventilated Shelf System,
Accessories and Finish Pieces
The elfa system has many accessories and
finish pieces that add to the overall
functionality and design. A few of these are
shown in the photos:
A. Closet rod holders that fit into the bottom of
the ventilated shelf bracket.
B. Placing shelf bracket covers for a clean look.
A.
B.
C. Placing ventilated
shelf liners used to
keep items from
slipping through wires.
D. Placing Top Track
Covers which hide
screw heads.
C.
D.
E.
E. Drawer liners relieve
“waffle effect” on
clothing in drawer.
The Completed elfa® Project With Drawing
As you can see, the
placement of some
items changed – easy
to do with elfa® modular
system – on 2’ centers,
many parts are interchangeable.
BEFORE
AFTER