Tablets - r_shanthini
Download
Report
Transcript Tablets - r_shanthini
PM3125: Lectures 18 to 21
Content of Lecture 18:
- Compression & Compaction
in Tablets Formation
Prof. R. Shanthini
22 Oct 2012
Principle of tablet production
Active substance synthesis
Blending and Granulation
Compression
Coating
Package
Prof. R. Shanthini
22 Oct 2012
Compressed tablets
Advantages and disadvantages of compressed
tablets
Types of tablets
Tablet compression machine
Tableting methods
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Advantages
Production aspect
Large
scale production at lowest cost
Easiest and cheapest to package and ship
High
stability
User aspect (doctor, pharmacist, patient)
Easy
to handling
Lightest
and most compact
Greatest dose precision & least content variability
Coating can mark unpleasant tastes & improve
acceptability
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Disadvantages
Some drugs resist compression into dense
compacts
Drugs with poor wetting, slow dissolution,
intermediate to large dosages may be difficult or
impossible to formulate and manufacture as a
tablet that provide adequate or full drug
bioavailability
Bitter taste drugs, drugs with an objectionable
odor, or sensitive to oxygen or moisture may
require encapsulation or entrapment prior to
compression or the tablets may require coating
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Types of tablets – Production process
Compressed
Multiple
tablets
compressed tablets
Tablet within a tablets: core and shell
Multilayer tablet
Sugar
coated tablets
Protect tablets from moisture
Mask odor and flavor
Elegance
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Types of tablets – Production process
Film
coated tablets
Thin film coat
Soluble or insoluble polymer film
Chewable
tablets
Rapid disintegrate
Antacid, flatulance: rapid action
Children drug
Effervescent
tablets
Dissolve in the water before drink
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Ingredients used in tablet formulations
Drugs
Fillers, diluent, bulking agent
To
make a reasonably sized tablet
Binders
To
bind powders together in the wet granulation
process
To
bind granule together during compression
Disintegrants
To
promote breakup of the tablets
To
promote rapid release of the drug
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Ingredients used in tablet formulations (contd.)
Lubricants
To
reduce the friction during tablet ejection between
the walls of the tablet and the walls of the die cavity
Glidants
Reducing
To
friction between the particles
improve the flow properties of the granulations
Antiadherants
To
prevent adherence of the granules to the punch
faces and dies
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Ingredients used in tablet formulations (contd.)
Dissolution (enhancers and retardants)
Wetting agents
Antioxidants
Preservatives
Coloring agents
Flavoring agents
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Essential properties of tablets
Accurate dosage of medicament, uniform in
weight, appearance and diameter
Have the strength to withstand the rigors of
mechanical shocks encountered in its
production, packaging, shipping and dispensing
Release the medicinal agents in the body in a
predictable and reproducible manner
Elegant product, acceptable size and shape
Chemical and physical stabilities
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Tablet production
Powders intended for compression into tablets
must possess two essential properties
Powder fluidity
The material can be transported through the
hopper into the die
To produce tablets of a consistent weight
Powder flow can be improved mechanically by the
use of vibrators, incorporate the glidant
Powder
compressibility
The property of forming a stable, intact compact
mass when pressure is applied
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Tableting procedure
Filling
Compression
Ejection
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Prof. R. Shanthini
22 Oct 2012
A — Die filling
B — Compression
C — Decompression
D — Lower punch
removal and
reapplication of load
to the upper punch
E — Tablet fully
ejected
1 refers to the final
compaction
conditions
Schematic diagram showing the manufacture of single and
bilayer tablets utilising uniaxial compaction.
Prof. R. Shanthini
22 Oct 2012
WET GRANULATION
DRY GRANULATION
DIRECT
COMPRESSION
1. Milling and mixing of drugs and excipients
2. Preparation of binder
solution
2. Compression into slugs
or roll compaction
3. Wet massing by addition of
binder solution or
granulating solvent
3. Milling and screening of
slugs and compacted
powder
4. Screening of wet mass
4. Mixing with lubricant and
disintegrant
5. Drying of the wet granules
5. Compression of tablet
6. Screening of dry granules
7. Blending with lubricant and
disintegrant to produce
“running powder”
8. Compression of tablet
Prof. R. Shanthini
22 Oct 2012
2. Compression of
tablet
Granulation
It is a process in which primary powder particles
are made to adhere to form larger, multiparticle
entities called granules.
It is the process of collecting particles together
by creating bonds between them.
Bonds are formed by compression or by using a
binding agent.
Prof. R. Shanthini
22 Oct 2012
Granulation (contd.)
The most common reasons given to justify
granulating are:
To impart good flow properties to the material,
To increase the apparent density of the powders,
To change the particle size distribution,
Uniform dispersion of active ingredient.
Prof. R. Shanthini
22 Oct 2012
Binders
Used in tablet formulations to make powders
more compressible and to produce tablets that
are more resistant to breakage during handling.
In some instances the binding agent imparts
viscosity to the granulating solution so that
transfer of fluid becomes difficult.
This problem can be overcome by adding some
or all binding agents in the dry powder prior to
granulation.
Prof. R. Shanthini
22 Oct 2012
Some granulation, when prepared in production
sized equipment, take on a dough-like
consistency and may have to be subdivided to a
more granular and porous mass to facilitate
drying.
This can be accomplished by passing the wet
mass through an oscillating type granulator with
a suitably large screen or a hammer mill with
either a suitably large screen or no screen at all.
Prof. R. Shanthini
22 Oct 2012
Oscillating type granulator
Prof. R. Shanthini
22 Oct 2012
Hammer mill
Drying
The most common conventional method of drying a
granulation continues to be the circulating hot air oven,
which is heated by either steam or electricity.
The important factor to consider as part of scale-up of an
oven drying operation are airflow, air temperature, and
the depth of the granulation on the trays.
If the granulation bed is too deep or too dense, the
drying process will be inefficient, and if soluble dyes are
involved, migration of the dye to the surface of the
granules.
Drying times at specified temperatures and airflow rates
must be established for each product, and for each
particular oven load.
Prof. R. Shanthini
22 Oct 2012
Fluidized bed dryers are
an attractive alternative to
the circulating hot air
ovens.
The important factor
considered as part of
scale up fluidized bed
dryer are optimum loads,
rate of airflow, inlet air
temperature and
humidity.
Prof. R. Shanthini
22 Oct 2012
Reduction of Particle size
Compression factors that may be affected by the particle
size distribution are flowability, compressibility, uniformity
of tablet weight, content uniformity, tablet hardness, and
tablet color uniformity.
First step in this process is to determine the particle size
distribution of granulation using a series of “stacked”
sieves of decreasing mesh openings.
Particle size reduction of the dried granulation of
production size batches can be carried out by passing all
the material through an oscillating granulator, a hammer
mill, a mechanical sieving device, or in some cases, a
screening device.
Prof. R. Shanthini
22 Oct 2012
Oscillating type granulator
Prof. R. Shanthini
22 Oct 2012
Hammer mill
Blending
Type of blending equipment often differs from that using
in laboratory.
In any blending operation, both segregation and mixing
occur simultaneously are a function of particle size,
shape, hardness, and density, and of the dynamics of
the mixing action.
Particle abrasion is more likely to occur when high-shear
mixers with spiral screws or blades are used.
When a low dose active ingredient is to be blended it
may be sandwiched between two portions of directly
compressible excipients to avoid loss to the surface of
the blender.
Prof. R. Shanthini
22 Oct 2012
Equipments used for mixing
Sigma blade mixer.
Planetary mixer.
Twin shell blender.
High shear mixer
Planetary mixer
Prof. R. Shanthini
22 Oct 2012
Dry Granulation (slugging)
A dry powder blend that cannot be directly compressed
because of poor flow or compression properties.
This is done on a tablet press designed for slugging, which
operates at pressures of about 15 tons, compared with a
normal tablet press, which operates at pressure of 4 tons
or less.
Slugs range in diameter from 1 inch, for the more easily
slugged material, to ¾ inch in diameter for materials that
are more difficult to compress and require more pressure
per unit area to yield satisfactory compacts.
If an excessive amount of fine powder is generated during
the milling operation the material must be screened & fines
recycled through the slugging operation.
Prof. R. Shanthini
22 Oct 2012
Dry Compaction
Granulation by dry compaction can also be achieved by
passing powders between two rollers that compact the
material at pressure of up to 10 tons per linear inch.
Materials of very low density require roller compaction to
achieve a bulk density sufficient to allow encapsulation
or compression.
One of the best examples of this process is the
densification of aluminum hydroxide.
Pilot plant personnel should determine whether the final
drug blend or the active ingredient could be more
efficiently processed in this manner than by conventional
processing in order to produce a granulation with the
required tabletting or encapsulation properties.
Prof. R. Shanthini
22 Oct 2012
Compression
The ultimate test of a tablet formulation and
granulation process is whether the granulation can
be compressed on a high-speed tablet press.
During compression, the tablet press performs the
following functions:
Filling of empty die cavity with granulation.
2. Precompression of granulation (optional).
3. Compression of granules.
4. Ejection of the tablet from the die cavity and take-off of
compressed tablet.
1.
Prof. R. Shanthini
22 Oct 2012
Tablet compression machines
Hopper for holding and feeding granulation to be
compressed
Dies that define the size and shape of the tablet
Punches for compressing the granulation within
the dies
Cam tracks for guiding the movement of the
punches
Feeding mechanisms for moving granulation
from the hopper into the dies
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Singe punch machine
The compression is applied by the upper punch
Stamping press
Prof. R. Shanthini
22 Oct 2012
Source: Assoc. Prof. Dr. Jomjai Peerapattana, Faculty of
Pharmaceutical Sciences, Khon Kaen University
Singe punch rotary machine
Prof. R. Shanthini
22 Oct 2012
Singe punch machine
Upper and
Lower Collar
Collar locker