Transcript Integrating Cisco Press Resources into the Academy Classroom

Switching Basics and Intermediate
Routing CCNA 3
Chapter 8
www.ciscopress.com
Virtual LANs
Introduction
• Ethernet switches can create virtual LANs
(VLANs)
– A VLAN is a logical broadcast domain that
spans multiple physical LAN segments
– Can be grouped by job functions or
departments, regardless of physical location
– Modern VLANs typically are localized,
spanning only one or two switches
www.ciscopress.com
Virtual LANs
Introduction
• Traffic between VLANS is restricted
– Switches and bridges forward unicast,
multicast, and broadcast traffic only on LAN
segments that serve the VLAN to which the
traffic belongs
– Devices on a VLAN communicate only with
devices on that VLAN unless a router is
configured to enable inter-VLAN routing
• Layer 3 Switches (multilayer switches) commonly
do inter-VLAN routing
www.ciscopress.com
Virtual LANs
Introduction
• Properly designed VLANs are powerful
tools, providing:
– Segmentation
– Flexibility
– Security
– Simplification of additions, moves, and
changes to the network
– Control of Layer 3 broadcasts
www.ciscopress.com
VLAN Concepts
Introduction
• VLANs allow almost complete
independence of physical and logical
topologies
– Can define groups of workstations, separated
by switches and on different LAN segments,
as one broadcast domain
• A VLAN is a logical group of network
services, workstations, and devices not
restricted to one physical LAN segment
www.ciscopress.com
VLAN Concepts
Introduction
• VLANs facilitate easy administration of
logical groups of workstations and servers
– Can communicate as if they were on the
same LAN segment
• VLANs can be configured with the Catalyst
switch CLI or via centralized management
software
– A group of switch ports can be assigned to a
single VLAN
www.ciscopress.com
VLAN Concepts
Introduction
Traditional VLAN Implementation
www.ciscopress.com
VLAN Concepts
Introduction
• A workstation in a VLAN is restricted to
communicating with file servers in the
same VLAN group unless a router is used
to provide inter-VLAN connectivity
• VLANs logically segment the network into
different broadcast domains
– Packets are only switched between ports that
belong to the same VLAN
www.ciscopress.com
VLAN Concepts
Introduction
• Original purpose of VLANs was to supply
segmentation services traditionally done by
routers
• VLANs offer segmentation, flexibility, and
security
• Routers in VLAN topologies provide broadcast
filtering, security, and traffic management
• Switches do not bridge traffic between VLANs as
this would violate the integrity of the VLAN
broadcast domain; traffic is routed between
VLANs
www.ciscopress.com
VLAN Concepts
Broadcast Domains with VLANs and Routers
• A VLAN is a logical broadcast domain
– Can span multiple physical segments
– Within a switched network, can offer segmentation
and organizational flexibility
– Workstations can be segmented logically by
functions, project teams, and applications
• A switch port can be assigned to only one VLAN,
adding a layer of security
• Ports in the same VLAN share broadcasts; ports
in different VLANs do not share broadcasts
– Containing broadcasts helps network performance
www.ciscopress.com
VLAN Concepts
Broadcast Domains with VLANs and Routers
• A VLAN can:
– Exist on a single switch or span multiple
switches
– Include workstations in a single building or
multiple-building infrastructures such as a
campus
– Connect across WANs using service provider
technologies such as IEEE 802.1Q-in-Q
VLAN Tag Termination
www.ciscopress.com
VLAN Concepts
Broadcast Domains with VLANs and Routers
• Routing or Layer 3 switching enables
traffic to flow between VLANs
– Layer 3 switching is basically wire-speed
routing enabled by dedicated applicationspecific integrated circuits (ASICs)
• ASICs are microchips designed for a specific
function
www.ciscopress.com
VLAN Concepts
Broadcast Domains with VLANs and Routers
Inter-VLAN Communication Requires a Router
www.ciscopress.com
VLAN Concepts
Broadcast Domains with VLANs and Routers
• VLAN implementation on a switch causes certain actions
to occur:
– The switch maintains a separate bridging table for each VLAN
• If the frame comes in on a port in VLAN 1, the switch
searches the bridging table for VLAN 1
– When the frame is received, the switch adds the source address
to the bridging table if it is currently unknown
– The destination address is checked so a forwarding decision can
be made
– For learning and forwarding, the search is made against the the
address table for that VLAN only
• If the destination IP address of an IP packet is on a
different VLAN (subnet), a router or Layer 3 switch must
route the packet
www.ciscopress.com
VLAN Concepts
VLAN Operation
• A Cisco Catalyst switch operates in a network
like a traditional bridge
– Each VLAN on the switch implements address
learning, forwarding, and filtering decisions
– Loop avoidance mechanisms are used on each VLAN
as if they were separate bridges
• Internally, the switch forwards data only to ports
on the same VLAN
– Limits the transmission of unicast, multicast, and
broadcast frames to the same VLAN
– Floods only to other ports in the same VLAN
www.ciscopress.com
VLAN Concepts
VLAN Operation
• For a VLAN to span across multiple
switches, a trunk is required
Trunk Carrying Traffic for Three VLANs over the Same Link
www.ciscopress.com
VLAN Concepts
VLAN Operation
• A trunk can carry traffic for multiple VLANs
• Summary of VLAN operations:
– Each logical VLAN is like a separate physical
bridge
– VLANs can span across multiple switches
– Trunks carry traffic for multiple VLANs
– Trunks use special encapsulation to
distinguish between different VLANs
www.ciscopress.com
VLAN Concepts
VLAN Operation
• VLAN ports have membership modes:
– Static: an administrator statically configures the
assignment of VLANs to ports
– Dynamic: Catalyst switches can use VLAN
Management Policy Server (VMPS) – not widely
deployed; must be running the CatOS operating
system
• Catalyst 2950 cannot use VMPS as it runs the Cisco IOS
• VMPS contains a database that maps MAC addresses to
VLAN assignments
• When the switch receives a frame, it examines the source
MAC address and assigns the port to the correct VLAN
www.ciscopress.com
VLAN Concepts
VLAN Operation
Static and Dynamic VLAN Membership Modes
www.ciscopress.com
VLAN Configuration
Introduction
• Before creating a VLAN, decide whether to use
the optional VLAN Trunking Protocol (VTP) to
maintain global VLAN configuration on the
network
• Most Catalyst switches support up to 64 active
VLANs (2950 switches with standard image
support up to 250 VLANs, some advanced IOS
images up to 4094 VLANs)
• A separate instance of spanning tree is run on
each VLAN
www.ciscopress.com
VLAN Configuration
Introduction
• Various default VLANs are configured to support
various media and protocol types
– The default Ethernet VLAN is VLAN 1
– Cisco Discovery Protocol (CDP) and VTP
advertisements are sent on VLAN 1
• CDP is a proprietary Layer 2 protocol used to discover
information about neighboring Cisco devices
• The switch must have an IP address to be
remotely managed
– Assigned to the management VLAN, VLAN 1
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
• The most common method of configuring
VLANs is to assign port-to-VLAN
mappings on each switch
• VLANs are created with the vlan
command
– By default, a switch is in VTP server mode so
that you can add, change or delete VLANs
– Cannot make these changes in VTP client
mode
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
Adding a
VLAN
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
Adding a VLAN
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
• To modify an existing VLAN, use the same
command syntax
Changing the Name of a VLAN
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
• After creating a VLAN, a single port or multiple
ports can be manually assigned to it
– When assigning a port to a VLAN with this method, it
is known as a static-access port
• Use the switchport access command to
configure the VLAN port assignment from
interface configuration mode
• Use the vlan vlan-number option to set staticaccess membership
• Use the dynamic option to have VMPS control
and assign the VLAN
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
Assigning Ports to a VLAN
(continued on next slide)
www.ciscopress.com
VLAN Configuration
Configuring Static VLANs
Assigning Ports to a VLAN (continued)
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
• Use the show vtp status command to verify a
recent configuration change
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
• Use the show interfaces interfaces
switchport command and the show
interfaces interfaces trunk command to
display the trunk parameters and VLAN
information for the port
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Verifying VLAN Trunking Information
www.ciscopress.com
(continues on next slide)
VLAN Configuration
Verifying VLAN Configuration
Verifying VLAN Trunking Information (continued)
www.ciscopress.com
(continues on next slide)
VLAN Configuration
Verifying VLAN Configuration
Verifying VLAN Trunking Information (continued)
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
• After configuring the VLAN, validate its
parameters with the show vlan id vlan-id or the
show vlan-name vlan-name command
Validating VLAN Parameters
(continues on next slide)
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Validating VLAN Parameters (continued)
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
• Use the show vlan brief command to display
one line about each VLAN
– Shows VLAN name, status, and switch ports
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
• Use the show vlan command to display
information on all configured VLANs
– Shows:
• switch ports assigned to each VLAN
• Type (default is Ethernet)
• Security association ID (SAID) used for the FDDI
trunk
• MTU (default of 1500 for Ethernet)
• Other parameters for Token Ring and FDDI
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Verifying VLAN Information with show vlan
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Verifying VLAN Information for a Particular Interface with
the show interfaces interfaces switchport command
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Verifying Spanning
Tree Information for
a Particular VLAN
with the show
spanning-tree vlan
command
(continued on next
slide)
www.ciscopress.com
VLAN Configuration
Verifying VLAN Configuration
Verifying Spanning Tree Information for a Particular VLAN with the
show spanning-tree vlan command (continued)
www.ciscopress.com
VLAN Configuration
Adding, Changing, and Deleting VLANs
• To add, change, or delete a VLAN, put the
switch in VTP server or transparent mode
– When changes are made in server mode,
they are automatically propagated to other
switches in the VTP domain
– VLAN changes made in transparent mode
affect the local switch only; changes are not
propagated to the VTP domain
www.ciscopress.com
VLAN Configuration
Adding, Changing, and Deleting VLANs
• After creating a new VLAN, make
necessary changes to port assignments
– Separate VLANs imply separate IP networks
– Plan the new IP addressing scheme and its
deployment to workstations before moving
users to the new VLAN
– Separate VLANs require inter-VLAN routing
• Set the appropriate default gateway and other
services such as Dynamic Host Configuration
Protocol (DHCP)
www.ciscopress.com
VLAN Configuration
Adding, Changing, and Deleting VLANs
• To modify VLAN attributes, use the vlan vlan-id
global configuration command
– Can change VLAN name but not VLAN number
– To use a different VLAN number, create a new VLAN
and then assign the ports to it
• To move a port to a different VLAN, use the
same commands used to make the original
assignment
– On a Catalyst 2950, use the switchport access
interface configuration command
• Do not need to remove a port from a VLAN to make this
change
www.ciscopress.com
VLAN Configuration
Adding, Changing, and Deleting VLANs
• If a VLAN is removed from a switch in that is in
VTP server mode, it is removed from all
switches in the VTP domain
• If a VLAN is removed from a switch in that is in
VTP transparent mode, it is removed only from
that switch
– Use the no vlan vlan-id command to remove a VLAN
– Before deleting a VLAN, be sure to move all ports to
another VLAN or communication will be lost
– To reassign a port to VLAN 1, use the no switchport
access vlan command
www.ciscopress.com
Troubleshooting VLANs
Introduction
• VLANs are common in campus networks
– Give network engineers flexibility in designing
and implementing networks
– Enable broadcast containment, security, and
connection of geographically separate
communities of interest (workgroups)
• Misconfiguration of a VLAN is one of the
most common errors in a switched
network
www.ciscopress.com
Troubleshooting VLANs
Introduction
Switched LAN
Troubleshooting
Process
www.ciscopress.com
Troubleshooting VLANs
Troubleshooting VLAN Problems
• Possible throughput problems:
– Bad adapter card
– Duplex mismatch
• Look for FCS errors, alignment errors, runts
• Auto-negotiation or mismatched settings
• Use this approach:
– Is problem on local side or remote side of the link
– What path is the packet taking (across trunks or nontrunks to other switches)
– If the show interfaces command shows rapidly
increasing collisions, may be an overloaded link or
duplex mismatch
www.ciscopress.com
Troubleshooting VLANs
Troubleshooting VLAN Problems
• Remember, switches minimize collisions
only in full-duplex mode
– In half-duplex mode, collisions still occur
because two devices can attempt to transmit
at the same time
• The only cure for collisions on Ethernet is
to run it in full-duplex mode
– Almost always done today
www.ciscopress.com
Troubleshooting VLANs
Troubleshooting VLAN Problems
VLAN
Problems
and
Solutions
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 1: One Device Cannot Communicate
with Another Device
– Make sure the IP address, subnet mask and VLAN
membership of the switch interface is correct by using
the show interfaces command
– If the host is in the same subnet as the switch
interface, make sure the switch interface and the
switch port to which the host is connected are in the
same VLAN, using the show interfaces and the
show vlan commands
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 1: One Device Cannot Communicate
with Another Device (continued)
– If the host is on a different subnet, ensure the default
gateway on the switch is configured with the address
of a router in the same subnet as the switch interface,
using the show ip route command
– Check the spanning-tree state on the port using the
show spanning-tree interface configuration
command
• If port is in listening or learning mode, wait until it is in
forwarding mode and try again
– Check that speed and duplex settings on host and
switch ports are correct; show interfaces command
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 1: One Device Cannot Communicate
with Another Device (continued)
– If the connected device is an end station:
• Enable spanning-tree PortFast on the port, using the
spanning-tree portfast interface command
– Places port in forwarding mode immediately
• Disable trunking on the port, using the no switchport trunk
interface command
• Disable channeling on the port with the no channel-group
interface command
– Make sure the switch is learning the MAC address of
the host, using the show mac-address-table
dynamic command
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 2: A Device Cannot Establish a
Connection Across a Trunk Link
– Make sure trunking mode has a valid configuration on
both ends of the link, using the show interfaces
trunk command
– Make sure the trunk encapsulation type on both ends
is valid, using the show interfaces interface-id
[switchport | trunk] command
– On IEEE 802.1Q trunks, check that the native VLAN
is the same on both ends of the trunk, using the show
interfaces interface-id [switchport | trunk] command
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 3: VTP Is Not Updating the
Configuration on Other Switches When the
VLAN Configuration Changes
– Make sure the switches are connected with
trunk links as VTP updates occur only over
trunk links; use the show interfaces trunk
command
– Ensure the VTP domain name matches on the
appropriate switches; use the show vtp
status command
www.ciscopress.com
Troubleshooting VLANs
VLAN Troubleshooting Scenarios
• Scenario 3: VTP Is Not Updating the
Configuration on Other Switches When the
VLAN Configuration Changes
– Check to see if the switch is in transparent mode
• Only switches in VTP server or client mode update their
configuration based on VTP updates
• Use the show vtp status command
– If using VTP passwords, the password must be the
same on all switches in the VTP domain
• To set or change the password, use the vtp password
command; clear a password with the no vtp password
command
www.ciscopress.com
Troubleshooting VLANs
Summary
• A VLAN is a set of network services
– Creates a single broadcast domain
– Not restricted to a physical LAN segment or single
LAN switch
– Configured through software, making it unnecessary
to move equipment and cables
• VLANs provide:
– Segmentation
– Design flexibility
– Security
www.ciscopress.com
Troubleshooting VLANs
Summary
• Routers in VLANs provide:
– Broadcast filtering
– Security
– Traffic management
• Routers route traffic between VLANs
– Switches can’t be used to bridge traffic
between VLANs; would violate integrity of
broadcast domain
www.ciscopress.com
Troubleshooting VLANs
Summary
• Primary benefit of VLANs is that they permit the
network engineer to organize the LAN logically
instead of physically
• A VLAN is a broadcast domain that one or more
switches create
– Improves overall network performance
– Switch keeps a separate bridging table for each
VLAN
– When a switch receives a frame, it examines the
source MAC address and adds it to the bridging table
for that VLAN if it was previously unknown
– Switch then makes a forwarding decision
www.ciscopress.com
Troubleshooting VLANs
Summary
• Static VLANs are ports on a switch that
are manually assigned to a VLAN
– Can use a management application or the
switch operating system commands
– Ports maintain their assignments unless they
are manually changed
• Dynamic VLANs do not rely on ports being
assigned by an administrator to specific
VLANs
www.ciscopress.com
Troubleshooting VLANs
Summary
• Use these commands to verify VLAN
configuration:
– show vtp status, show vlan, show vlan brief, show
vlan id vlan-id, show vlan name vlan-name, show
interfaces switchport, show interfaces trunk, and
show spanning-tree vlan
• Use a systematic approach to troubleshoot
– Start with physical indications, such as LED status
– Then proceed to Layer 2 and Layer 3 problem
isolation
www.ciscopress.com