GRID SYSTEMS Size and Shape of the earth: Approximate sphere - about 20 km wider at equator than poles.

Circumference = 40,000 km (25,000 miles).

The Graticule, consisting of meridians and parallels forms a natural Geographic Grid. The grid has a natural basis - the equator and poles of the earth.

Harry Williams, Cartography 1

Any point on the surface of the earth can be located in terms of its latitude and longitude (angles measured from the equator and Prime Meridian).

Point P for example is at 30 o north, 20 o west.

Passes through Greenwich, England.

Latitude varies from 0 o to 90 o north or south.

Figure courtesy of Anthony P. Kirvan, and

NCGIA Core Curriculum in GIScience

. Longitude varies from from 0 o to 180 o east or west.

Harry Williams, Cartography 2

Degrees, Minutes, and Seconds

•Angular measurement must be used to specify location on the earth's surface. A circle has 360 degrees, 60 minutes per degree, and 60 seconds per minute. Example: 45° 33' 22" (45 degrees, 33 minutes, 22 seconds). • At the equator 1 degree of longitude = 40,000 km/360 = 111 km. 1 minute = 111 km/60 = 1.85 km. 1 second = 1.85 km/60 = 30 m. Note: 1' latitude at the equator = 1 nautical mile; 1 knot = 1 nautical mile per hour.

• Meridians converge, therefore at 60 o latitude, 1 degree of longitude = 55.5 km.

•There are 3,600 seconds per degree (60 x 60). •It is sometimes necessary to convert this conventional angular measurement into decimal degrees (e.g. often used in GIS’s). E.g. 45° 33' 22“ = 45° 2,002“ = 45° 2,002/3,600 = 45.55°.

Harry Williams, Cartography 3

By convention, latitude is given before longitude. E.g. the corner of the map is: 33 o 97 o 15’ N 07’ 30” W Harry Williams, Cartography 4

Plane-coordinate Grid Systems.

Problems with the Geographic Grid (Latitude and Longitude): 1. Curved lines on many projections.

2. Lines not equidistantly-spaced.

3. Scale variations.

A practical grid system should Have: 1. Straight lines.

2. Lines intersect at right angles.

3. Lines equally-spaced.

4. Grid squares have equal area.

Two examples are: Universal Transverse Mercator Grid System State Plane Grid System Harry Williams, Cartography 5

Universal Transverse Mercator Grid System (UTM) A transverse cylindrical projection is used: A narrow strip, 6 o of longitude wide, astride the

central meridian

has very little distortion.

Harry Williams, Cartography 6

By moving the cylinder around the globe, 60 strips can be created: these are UTM grid zones, numbered 1-60.

Harry Williams, Cartography 7

For example, grid zone 14 is centered on 99 o west and runs through Texas. This zone covers 96 o to 102 o west. A 1-km grid is superimposed onto this map. The grid lines are numbered by their distance north from the equator and east from an imaginary base line which is arbitrarily located 500 km west of the central meridian (so the central meridian becomes the 500,000 m east grid line). Any point within the grid zone can be fixed by these two distances (a northing and an easting).

Harry Williams, Cartography 8

Harry Williams, Cartography 9

The UTM reference: Zone 14: 621161 m E, 3349894 m N is a unique location within grid zone 14, accurate to the nearest meter. The grid zone number must be specified because this same reference occurs in all grid zones.

When working on a map of a small area in the U.S. such as Denton, UTM grid references are usually given to the nearest hundred meters (i.e. the nearest 1/10 of a grid square; so 621161 m E would become 621200 m E). Also by convention, the zone number, the first digit in the easting, the first two digits in the northing and the two zeros (10’s and 1’s of meters) can be dropped. The example above would then become: 212499 …. This is a 6-digit UTM grid reference.

Harry Williams, Cartography 10

For example, this point is 674100 m east and 3680300 m north in grid zone 14. It’s 6 digit UTM reference is: 741803 UTM grid tick Harry Williams, Cartography Note: to find the original UTM reference, you can put the “missing’ numbers back, so 741803 becomes 674100 m east and 3680300 m north 11

Plane-coordinate grid references like UTM references can be used to calculate distances between points because they are based on measured distances. For example, the UTM references 123456 and 333777 would have an easting separation of 33300 -12300 m = 21000 m = 21 km; and a northing separation of 77700 – 45600 m = 32100 m = 32.1 km. By Pythagoras theorem, the straight line distance between these points would be: sqrt 21 2 + 32.1

2 = sqrt 1471.41 = 38.36 km.

333777 38.36 km 32.1 km 123456 21 km Harry Williams, Cartography 12

State Plane Grid System: In the United States, the State Plane System was developed in the 1930s and was based on the North American Datum 1927 (NAD27). This is similar to the UTM system. Older NAD-27 coordinates are in feet. Newer NAD-83 coordinates are usually in meters (can be in feet too). State plane systems were developed in order to provide local reference systems that were tied to a national datum (NAD-27, NAD-83). Larger states are divided into several zones. Lambert Conformal Conic projections are commonly used for rectangular zones with a larger east-west than north-south extent. Harry Williams, Cartography 13

Texas has 5 NAD-83 State Plane zones. Harry Williams, Cartography 14

Each zone has an origin with a false easting and northing to ensure positive coordinates.

Harry Williams, Cartography 15

Some examples of State Plane Coordinates in Austin: Harry Williams, Cartography 16

Harry Williams, Cartography State Plane coordinates are also shown on USGS maps (although there are only a few tick marks) 17

Who uses the State Plane System? Many local governments do. North Central Texas Council of Governments (NCTCOG www.dfwinfo.com

) map data is usually in State Plane Coordinates. Example metadata is shown here for a map of city boundaries.

Harry Williams, Cartography 18