Transcript Slide 1
Rutherford Backscattering
Spectrometry
Elemental analysis technique where alpha particles are scattered off of targets and
is used to determine elemental composition and thin-film thickness.
The main points to learn are:
1. The scattering is proportional to the squares of both the charge of the incident
particle and the target nucleus.
2. The number of scattered particles varies as the inverse square of the kinetic
energy of the incident particle.
3. The scattering is inversely proportional to the fourth power of sin(θ/2), where θ is
the scattering angle.
4. For thin targets, the scattering is proportional to the target thickness, t.
The Rutherford Scattering Experiment
Scattering line
Fradial
Ftangential
Mprojectile
vo
b
Incident particle approaches at a
separation distance, b, called the
impact parameter, from the
target nucleus and scatters at an
angle with respect to its initial
direction due to the Coulomb
force.
Mtarget
Fscattering
ze Ze
4 0
r2
1
where z = 2 and Z = atomic number of target
Momentum triangle and the Impulse equations
zZe 2
pradial 2m v0 sin I radial
cosdt
2
2
4
r
0
p
pf = mvf
ptangential 0 I tangential 0
p0 = mv0
Central force means constant angular momentum:
d
r2
L m v0b m r
dt
d
dt
v0b
2
zZe 2
zZe 2 1
I radial
cosdt
cosd
2
4 0 r
4 0 v0b
Limits of integration and the
impact parameter: ;
i
f
2
2
i f i
f
zZe 2
I radial
4 0v0b
2
zZe 2
cos
d
cos
p
2
m
v
sin
radial
0
4 0v0b
2
2
2
zZe 2
b
cot
4 0 m v02
2
Relation between b and !
The Kinematic Factor - K
The kinematic factor is the ratio of the scattered alpha particle’s energy to its
incident energy gives a convenient method for determining the elemental make
up of the target atoms in the sample. To determine K we proceed as follows…
He
He
M
M
Assuming that the collision is elastic we apply conservation of momentum and
kinetic energy to the above situation to obtain:
p x : mHe vi , He mHe v f , He cos MV cos
p y : 0 mHe v f , He sin MV sin
KE :
pi2,He
2mHe
p 2f , He
2mHe
pM2
2M
The Kinematic Factor - K
We eliminate the dependence and the momentum of the target nucleus (since it
is difficult to measure anyway) in favor of the mass of the target atom, the mass
of the helium nucleus and the scattering angle .
E1
1
K
E0 mHe M
2
2
2
mHe cos M mHe sin
2
Knowing, or calculating the kinematic factor allows you to determine the mass of
the target atom and thus chemically identify the atom.
Now what you need is a target and a spectrum of number of detected alpha
particles versus the energy of the alpha particles.
To calibrate the energy spectrum (so we know the leading edge energy in order to
calculate the kinematic factor) we use a known energy alpha emitter.
Our choice is 241Am whose alpha particle energies are approximately 5.4 MeV.
The RBS Experiment
Start with a beam of 3.3 MeV alpha particles incident on a target of unknown
composition.
Determine the elemental composition of the sample based on the energies of the
scattered alpha particles.
Chemical identification based
on the kinematics factor.
Letting:
M1 = mass of helium ion,
M2 = mass of target species,
= scattering angle.
2
E
1
M 1 cos M 22 M 12 sin 2 scattered
K
Eincident
M 1 M 2
Chemical identification of the target elements
using the kinematic factor.
E0 = 2.0 MeV He
E1 = 1830 keV
K = 0.9150
M2 = 181amu
Tantalum
This is a spectrum of 2.0 MeV alpha particles
incident on a thin film of “unknown composition”
scattered at 170o.
Thickness determination from a thin-film.
E a x
E KE0 E1
Incident a-particle, Eo
Scattered a-particle from front edge, KEo
counts
Incident a-particle, Eo
Scattered a-particle from back edge, E
and emerges with E1
Al peak
E1
KEo
Energy
Thickness determination from a thin-film.
x
dE
x
E
cos1
E0
x
E
Inward:
1
x
dE
E
cos 2
KE
x
E
Outward:
If
E
x
1 -angle between incident
beam and horizontal.
2 -angle between exiting beam
and horizontal.
is assumed constant along the inward and outward paths, then
dE
x
E E0
E
E in
E0
x
E
Inward:
x
1
x
dE
x
Outward:
E1 KE
E
cos 2
E out
KE
x
E
Here we don’t know the energy at the back edge, rather only the energy that leaves
the target having been scattered from the back edge. So we can eliminate this energy
E.
Thickness determination from a thin-film.
Solving for E and equating the two resulting expressions we find:
E
E1 E
E E0
x
x in
K x
out
x
K cos 2
From our diagram we see that
E
KE 0 E1 E K
x
E
x
in
out
1
x Sx
cos180
Which give us a depth scale that is linear in the energy loss of the alpha particle.
S is called the energy loss factor, which involves the stopping power of the alpha particle
in the element in question and as the alpha particle travels farther it loses energy in
proportion to the penetration depth in the sample.
In general the stopping powers are not constant, but energy dependant. However, if the
film is thin then these stopping powers will be roughly constant.
Surface Energy Approximation for S0 in Thin Films.
If x is small then E will be small and then we can evaluate the stopping powers on
the from and back surfaces.
Thus we find:
E
S0
x
1
E
K
cos180 x
E0
KE0
So, now we have to look up S0 for a particular element and for a given .
After the elements are identified, you can use the tables provided to look up S0 for
your element and from E, you can calculate the thickness of the films on the surface
of the substrate and the thickness of the substrate.
Now for Ta, we find at 2.0 MeV and = 170o, So = 118.1 eV / A. Thus the thickness
of the tantalum foil is:
E 0.045106 eV
x
381A
ev
So
118.1 A
For this lab you are given 3 files of .spe type
•Open the files with a text editor and delete the header and footer BUT take the
calibration data first from the footer.
•The energy calibration data is in the footer and is the only number given that is
not zero. This represents the number of keV per channel, of which there are 8192
of them.
•Save the file as a .dat or .txt file.
•Import the data in to Excel and make a thin-line curve using the energy
calibration that you took.
Determine the elemental composition of the each of the three spectra.
ONLY from the PHY300_RBS_160degree_ManyElements data that you have,
determine the thickness of each of the layers that were seen. Be very careful when
looking at the graphs you make. There are some very small peaks that need to be
determined.
Do not worry about doing an uncertainty analysis for this lab.
The lab report for everyone is due next Thursday, June 6 at noon.