Transcript Predstavitev Orodje SLO

MOTORBIKE TOOLS
Igor Žmavc
December, 2013
www.uniortools.com
3050/2BI Clutch and gear wheel
holding tools








The tool is designed for holding the clutch, gears and the cam shaft
when tightening gears in the range from 40 up to 130 mm
Usage for all types of motorbikes
Its wedge-shaped gripping shanks provide grip between teeth while
preventing them from being damaged
The tool also includes a screw, which enables the tool to be fixed in a
certain position and, consequently, a firm grip
Material: special steel C45- 6 mm; hardened and tempered 30-35HRc
Max. allowable torque: 200 Nm
Surface finish: chrome plated according to EN12540
Ergonomic heavy duty double component handle
3051/2BI Rotor and sprocket
holding tools








The tool is designed for holding the magnet and the sprocket
Due to its universal structure, it allows holding holes with a diameter of
5 or 9 mm and at a distance between 20 to 180 mm
Usage for all types of motorbikes
The tool also has a screw that enables fixing of the tool at the actual
distance between holes on the magnet or the sprocket
Material: St 37- 6 mm; nozzle C45, hardened & tempered 40- 45HRc
Max. allowable torque: 150 Nm
Surface finish: chrome plated according to EN12540
Ergonomic heavy duty double component handle
3052/2BI Valve spring
compressor for motorbikes

This tool is used to attach and detach valve springs and features a
self-locking lever and quickly-adjustable fittings (dim. 17, 21 and 25
mm) to allow it to be used with all kinds of engines
NEW



Material: special tool steel C45 – 4 mm; material of fittings: C45
Hardened and tempered 40- 45HRc
Chrome plated EN 12540; Ergonomic heavy duty double component
handle
3055/4A,B Flywheel puller with
external thread


Allows flywheel removal without pulling motor from hull
The tool has different sizes of external thread, thus enabling coverage
of the majority of motor types that have a magnet with an internal
thread:
M10x1
M14x1,5
M16x1,5
M16x1,5
M18x1,5
M18x1,5
M20x1,5
M24x1
M22x1,5
M27x1L
3055/4A



3055/4B
On each axis, there is an attachment for an open-end wrench that
makes the removal of the magnet easier
Material: special tool steel C45; hardened and tempered 40- 45HRc
Surface finish: blacken to standard DIN 50938
3056/2 Socket 1/2" with thin
wall

Intended for use where there is not enough place for working with
standard socket wrenches



Material: 25CrMo4; hardened and tempered 42- 48HRc
Surface finish: chrome plated according to EN12540
Will not withstand torque according to ISO 2725-1 standard for
standard socket wrenches
3057.1/2 Universal variator
holder tool


for scooters PIAGGIO, GILERA 50-125ccm; water- and air-cooled
it is used as a block for the gear on the starter when untightening the
front part of the drive

comes with 3 different lengths of accessories (7,5 mm, 10 mm in 25,5
mm) that cover several types of drives
Material: St37- 4 mm; nozzle C45, hardened and tempered 30- 35HRc
Surface finish: chrome plated according to EN12540


3057/2 Variator and clutch drive
holder tool with ring wrench
 For scooters PIAGGIO, GILERA 50-125ccm; water- and air-cooled
 Tool has a triple function:
1. it is used as a block for the gear on the starter when untightening the
front part of the drive
2. accessories for holding the pot on the back part of the drive for
untightening the nut
3. Wrench S34/S38 for untightening the inside nut of the back part of the
drive



comes with 3 different lengths of accessories (7,5 mm, 10 mm in 25,5
mm) that cover several types of drives
Material: St37- 4 mm; nozzle C45, hardened and tempered 30- 35HRc
Surface finish: chrome plated according to EN12540
3058/2 Spark plug socket 3/8"
with thin wall

Intended for use where there is not enough space for working with
standard wrenches for replacing spark plugs


Drop forged, material: 25CrMo4; hardened and tempered 42- 48HRc
Surface finish: chrome plated according to EN12540
3059 Valve seal removal set for
motorbikes




Enables the removal of valve seals without removing the head of the motor
the accessories covers the following dimensions of spark plugs:
M10x1, M12x1.25, M14x1.25 and M18x1.5
accessories Ø8 mm, Ø13 mm and Ø16 mm for removing pins
accessories Ø12 mm in Ø14 mm for assembling seals
3059 Valve seal removal set for
motorbikes

Accessories Ø5 mm in Ø9 mm for assembling pins
3200/2BI Chain breaker, press and
riveting tool for motorbike

Chain breaker, press and riveting tool for REGINA, DID and RK chains
with graduation:
415, 420, 428, 520, 525, 530, 532
3200/2BI Chain breaker, press and
riveting tool for motorbike
3201/2 Tool for controlling cam belt
tension for motorcycle

it is used for the control of the tension of the drive belts
 Controlling tool is mounted onto the belt. On the marked part of the
engine the belt is forced by hand to establish the sag of the
belt so that it is in conformance with the pressure force of 45N
and the sag as defined by the manufacturer the belt

Used in accordance with the servicing instructions
3301/2 Spoke wrench for motorcycle

The spoke wrench is used for tightening spoke nipples



Material: special tool steel 31CrV3, thickness 6 mm
Hardened and tempered: 40- 45HRc
Surface finish: chrome plated according to EN12540
3302/6 Stand for motorcycle wheel
alignment


It enables radial control of the rim position with a sensor
The geometry of the calipers enables a simultaneous axial control for
accurate truing of the rim
- Wheels with dimensions 19” to
max. 32” inches can be centered
- for axis dimensions of 12 to 36 mm



The stand has a spirit level for setting in a horizontal position
The stand enables fixing of cones to the axis that enable the centering
of the wheel on its own bearings, thus preventing the possibility of
centering errors
Material: steel DC01; lacquered E/P
3303/2 Disc spreader for motorcycle





The tool is used for compressing brake pistons when replacing brake
pads
Is useful for compressing single, double and tripple brake pistons
For compressing double or triple brake pistons, we leave the used
brake pads in the brake housing. This will prevent one of the pistons
being pushed from the housing.
Material: special tool steel C45; hardened and tempered 35- 40HRc
Surface finish: chrome plated according to EN12540
3305/2 Holding tool for cartridge rod
for motorbikes


This tool is used to holding the cartridge rod
Useful for most types of motorcycles


Material: special tool steel C45, 2 mm
Surface finish: chrome plated according to EN12540
3401/2P Flexible hook wrench for
motorbikes

For operate setting the telescopes of motorbikes and scooters from Ø32
till Ø60 mm

The slim version of the wrench enables the setting of slim toothed nuts




Material: special tool steel C45, 4 mm;
Hardened and tempered 30- 35 HRc
Plastic dipped handle
Surface finish: chrome plated according to EN12540
3600/2BI Spring hook

Tool is used for assembling and disassembling springs (spring for
support legs, seat and reservoir, by exhaust systems, as assistance in
assembling the chain of the cam shaft, etc)




Material: special tool steel C45;
Hardened and tempered: 45- 50HRc
Surface finish: chrome plated according to EN12540
Ergonomic heavy duty double component handle
3700 Scooter tool set

By using the tool set, you can disassemble:
1. the entire shield (plastic parts)
2. most parts of the frame
3. engine parts like:
- replacing spark plugs
- changing oil in the transmissions (of the gearbox)
- disassembling various engine bonnets
- disassembling brakes and replacing brake pads
3700PRO Scooter tool set

By using the tool set, you can disassemble:
1. the entire shield (plastic parts)
2. most parts of the frame
3. engine parts like:
- replacing spark plugs
- changing oil in the transmissions (of the gearbox)
- disassembling various engine bonnets
- disassembling brakes and replacing brake pads
- changing brake fluid
- disassembling wheels
- for various suspensions and holders
1977/6 Oil-filter wrench


for assembling or dissasembling oil filters in restricted access area
used with ratchet 3/8" and proper extension bar
M
»
»
NEW M
NEW M
NEW M
M
M



Material: tool steel St14 / DC04;
Max. allowable torque: 140 Nm
Surface: coated with electro-black oxide finish for rust protection
192/2HX Hexagonal screwdriver
socket 1/2“

dimensions (mm) 17, 19, 22, 24 are used for the removal and fitting of
front wheels
NEW
NEW




made according to standard DIN 7422; min. allowable torque: 569 Nm
socket ½”: material 25CrMo4, Hardened and tempered 30- 35HRc;
Surface finish: chrome plated EN12540
Bit S17/S19: mat. 50CrV4; hardened and tempered 47-50HRc;
anticorosive oiled
Bit S22/S24: mat. C45, hardened and tempered 44-48HRc; anticorosive
oiled
689/2BI Inner bearing puller

It is used for pulling different types of bearings. The bearing is gripped
from the inside side and pulled out.
 The bearing is extract with a 1 kg weight
 Ergonomic heavy duty double component handle
Arm:
 Material: special tool steel 42CrMo4;
 Hardened and tempered 48- 52 HRc
 Surface finish: blacken to standard DIN 50938