Transcript chapter5

Convection
• Heat transfer in the presence of a fluid motion on a solid surface
•Various mechanisms at play in the fluid:
- advection  physical transport of the fluid
- diffusion  conduction in the fluid
- generation  due to fluid friction
•But fluid directly in contact with the wall does not move relative to it; hence
direct heat transport to the fluid is by conduction in the fluid only.
U
y
U
u(y) q”
Ts

qconv
But
T
y
T
 kf
y

  hTs  T 
 y 0


 depends
 y 0
y
U
y
T
T(y)
T
on the whole fluid motion, and both fluid flow
and heat transfer equations are needed
T(y)
Ts
Convection
Free or natural convection
(induced by buoyancy
forces)
Convection
forced convection (driven
externally)
Heat transfer rate q = h( Ts-T  )W
h=heat transfer coefficient (W /m2K)
(h is not a property. It depends on
geometry ,nature of flow,
thermodynamics properties etc.)
May occur with
phase change
(boiling,
condensation)
Typical values of h (W/m2K)
Free convection:
gases: 2 - 25
liquid: 50 - 100
Forced convection:
gases: 25 - 250
liquid: 50 - 20,000
Boiling/Condensation:
2500 -100,000
Convection rate equation
U
y
U
u(y) q”
y
T
T(y)
Ts
Main purpose of convective heat
transfer analysis is to determine:
• flow field
• temperature field in fluid
q’’=heat flux = h(Ts - T)
q’’ = -k(T/ y)y=0
Hence, h = [-k(T/ y)y=0] / (Ts - T)
• heat transfer coefficient, h
The expression shows that in order to determine h, we
must first determine the temperature distribution in the
thin fluid layer that coats the wall.
Classes of convective flows:
• extremely diverse
• several parameters involved (fluid properties, geometry, nature of flow,
phases etc)
• systematic approach required
• classify flows into certain types, based on certain parameters
• identify parameters governing the flow, and group them into meaningful
non-dimensional numbers
• need to understand the physics behind each phenomenon
Common classifications:
A. Based on geometry:
External flow / Internal flow
B. Based on driving mechanism
Natural convection / forced convection / mixed convection
C. Based on number of phases
Single phase / multiple phase
D. Based on nature of flow
Laminar / turbulent
How to solve a convection problem ?
• Solve governing equations along with boundary conditions
• Governing equations include
1. conservation of mass
2. conservation of momentum
3. conservation of energy
• In Conduction problems, only (3) is needed to be solved.
Hence, only few parameters are involved
• In Convection, all the governing equations need to be
solved.
 large number of parameters can be involved
Forced convection: Non-dimensional groupings
• Nusselt No. Nu = hx / k = (convection heat transfer strength)/
(conduction heat transfer strength)
• Prandtl No. Pr = / = (momentum diffusivity)/ (thermal diffusivity)
• Reynolds No. Re = U x /  = (inertia force)/(viscous force)
Viscous force provides the dampening effect for disturbances in the
fluid. If dampening is strong enough  laminar flow
Otherwise, instability  turbulent flow  critical Reynolds number
d
Laminar
d
Turbulent
FORCED CONVECTION:
external flow (over flat plate)
An internal flow is surrounded by solid boundaries that can restrict the
development of its boundary layer, for example, a pipe flow. An external flow, on
the other hand, are flows over bodies immersed in an unbounded fluid so that the
flow boundary layer can grow freely in one direction. Examples include the flows
over airfoils, ship hulls, turbine blades, etc.
•Fluid particle adjacent to the
les
solid surface is at rest
T
Ts
•These particles act to retard the
motion of adjoining layers
• boundary layer effect
Momentum balance: inertia forces, pressure gradient, viscous forces,
body forces
x
q
Energy balance: convective flux, diffusive flux, heat generation, energy
storage
h=f(Fluid, Vel ,Distance,Temp)
Hydrodynamic boundary layer
One of the most important concepts in understanding the external flows is the
boundary layer development. For simplicity, we are going to analyze a boundary
layer flow over a flat plate with no curvature and no external pressure variation.
U
U
U
U
Dye streak
turbulent
laminar
transition
Boundary layer definition
Boundary layer thickness (d): defined as the distance away from the surface
where the local velocity reaches to 99% of the free-stream velocity, that is
u(y=d)=0.99U. Somewhat an easy to understand but arbitrary definition.
Boundary layer is usually very thin: d/x usually << 1.
Hydrodynamic and Thermal
boundary layers
As we have seen earlier,the hydrodynamic boundary layer is a region of a
fluid flow, near a solid surface, where the flow patterns are directly
influenced by viscous drag from the surface wall.
0<u<U,
0<y<d
The Thermal Boundary Layer is a region of a fluid flow, near a solid surface,
where the fluid temperatures are directly influenced by heating or cooling
from the surface wall.
0<t<T, 0<y<dt
The two boundary layers may be expected to have similar characteristics but
do not normally coincide. Liquid metals tend to conduct heat from the wall
easily and temperature changes are observed well outside the dynamic
boundary layer. Other materials tend to show velocity changes well outside
the thermal layer.
Effects of Prandtl number, Pr
dT
Pr >>1
 >> 
e.g., oils
d
d, dT
Pr = 1
=
e.g., air and gases
have Pr ~ 1
(0.7 - 0.9)
T  TW
u
similar to
U
T  TW
(Reynold’s analogy)
d
dT
Pr <<1
 << 
e.g., liquid metals
Boundary layer equations (laminar flow)
• Simpler than general equations because boundary layer is thin
T
U
U
y
d
x
dT
TW
• Equations for 2D, laminar, steady boundary layer flow
Conservation of mass :
u v

0
x y
u
u
dU   u 

Conservation of x - momentum: u  v
 U
 
x
y
dx y  y 
T
T   T 

Conservation of energy: u
v
 
x
y y  y 
• Note: for a flat plate, U  is constant , hence
dU 
0
dx
Exact solutions: Blasius
d
4.99
Boundarylayer thickness
x

Re x
w
0.664
Skin frictioncoefficient C f  1

2
Re x
2 U 

 Re  U  x ,    u
w
 x

y

L
1
1.328
Averagedrag coefficient C D   C f dx 
L0
Re L
Local Nusselt number Nu x  0.339Re x P r 3
1
1
2
Average Nusselt number N u  0.678Re L P r 3
1
2
1



y 0 
UL 

 Re L 

 

Heat transfer coefficient
• Local heat transfer coefficient:
1
1
Nu x k 0.339k Re x Pr 3
hx 

x
x
2
• Average heat transfer coefficient:
h
Nu k
L
1
1
0.678k Re L Pr 3

L
2
• Recall: qw  h ATw  T , heat flow ratefromwall
• Film temperature, Tfilm
For heated or cooled surfaces, the thermophysical properties within
the boundary layer should be selected based on the average
1
temperature of the wall and the free stream; Tfilm  2 Tw  T 
Heat transfer coefficient
Thermal Boundary
Layer, dt
Convection
Coefficient, h.
U
x
Laminar and turbulent b.l.
Laminar Region
Turbulent Region
Hydrodynamic
Boundary Layer, d
Turbulent boundary layer
* Re x increaseswit h x.Beyonda crit icalvalue of Reynoldsnumber
(Re x  Re xc ), t heflow becomest ransit ional and event uallyt urbulent.
Re xc 
U  xc

(For flow over flat plat e,xc  5 105 )
* T urbulentb.l. equat ionsare similar t olaminarones, but infinit ely
moredifficult t o solve.
* We will mainlyuse correlat ions based on experimental dat a :
C f  0.059Re x 0.2
C D  0.072Re L 
(Re x  5  105 )

1
0.072Re 0xc.8  1.328Re 0xc.5
Re L
Nu x  0.029Re 0x.8 P r 3

1

N u  0.036Re 0L.8 P r 3  P r 3 0.036Re 0xc.8  0.664Re 0xc.5
1
1

* Calculat eheat t rans
fer coefficient in usual way : h 
Nu k
et c.
x
Laminar Boundary Layer Development
1
d( x )
• Boundary layer growth: d  x
• Initial growth is fast
• Growth rate dd/dx  1/x,
decreasing downstream.
0 .5
0
0
0 .5
x
1
10
 w( x )
• Wall shear stress: w  1/x
• As the boundary layer grows, the
wall shear stress decreases as the
velocity gradient at the wall becomes
less steep.
5
0
0
0 .5
x
1
Example
Determine the boundary layer thickness, the wall shear stress of a laminar water flow
over a flat plate. The free stream velocity is 1 m/s, the kinematic viscosity of the water
is 10-6 m2/s. The density of the water is 1,000 kg/m3. The transition Reynolds number
Re=Ux/=5105. Determine the distance downstream of the leading edge when the
boundary transitions to turbulent. Determine the total frictional drag produced by the
laminar and turbulent portions of the plate which is 1 m long. If the free stream and
plate temperatures are 100 C and 25 C, respectively, determine the heat transfer rate
from the plate.
d ( x)  5
x
U
 5  103 x ( m).
Therefore, for a 1m long plate, the boundary layer grows by 0.005(m),
or 5 mm, a very thin layer.
0.332 U 2
The wall shear stress,  w 
 0.332U 
Re x
The transition Reynolds number: Re 
U  xtr

U 
x

0.0105
( Pa )
x
 5  105 , xtr  0.5( m)
Example (cont..)
The total frictional drag is equal to the integration of the wall shear stress:
FD 
xtr

0
w
(1)dx 
xtr
 0.332U
0

U 
x
0.664 U 2
dx 
 0.939( N )
Re xtr
Define skin friction coefficient: C f
Cf 
w
0.664

for a laminar boundary layer.
2
1 U 
Re x
2
Forced convection over exterior bodies
• Much more complicated.
•Some boundary layer may exist, but it is likely
to be curved and U will not be constant.
• Boundary layer may also separate from the
wall.
• Correlations based on experimental data can
be used for flow and heat transfer calculations
• Reynolds number should now be based on a
 UD
Re

D
characteristic diameter.

• If body is not circular, the equivalent
diameter Dh is used
4  Area
Dh 
Drag force
CD  1
2

U
 Anormal
2
Perimeter
;
hD
Nu 
k
Nu k
; h
D
Flow over circular cylinders
P r.62
Nu  C Re
P rs.25
m
D
Re D
C
m
1  40
0.75 0.4
40 - 103
0.51 0.5
103 - 2  105 0.26 0.6
2 105 - 106 0.08 0.7
All properties at free stream
temperature, Prs at cylinder
surface temperature
FORCED CONVECTION: Internal flow
• Thermal conditions
 Laminar or turbulent
 entrance flow and fully developed thermal condition
e.g. pipe flow
Thermal entrance region, xfd,t
For laminar flows the thermal entrance length is a function of the
Reynolds number and the Prandtl number: xfd,t/D  0.05ReDPr,
where the Prandtl number is defined as Pr = / and  is the thermal
diffusitivity.
For turbulent flow, xfd,t  10D.
Thermal Conditions
• For a fully developed pipe flow, the convection
coefficient does not vary along the pipe length.
(provided all thermal and flow properties are constant)
h(x)
constant
xfd,t
x
• Newton’s law of cooling: q”S = hA(TS-Tm)
Question: since the temperature inside a pipe flow does not remain
constant, we should use a mean temperature Tm , which is defines
as follows:
Energy Transfer
Consider the total thermal energy carried by the fluid as
 VCvTdA  (mass flux) (internal energy)
A
Now imagine this same amount of energy is carried by a body
of fluid with the same mass flow rate but at a uniform mean
temperature Tm. Therefore Tm can be defined as
 VC TdA
v
Tm 
A
mCv
Consider Tm as the reference temperature of the fluid so that the
total heat transfer between the pipe and the fluid is governed by the
Newton’s cooling law as: qs”=h(Ts-Tm), where h is the local
convection coefficient, and Ts is the local surface temperature.
Note: usually Tm is not a constant and it varies along the pipe
depending on the condition of the heat transfer.
Energy Balance
Example: We would like to design a solar water heater that can heat up the water
temperature from 20° C to 50° C at a water flow rate of 0.15 kg/s. The water is
flowing through a 0.05 m diameter pipe and is receiving a net solar radiation
flux of 200 W/m of pipe length. Determine the total pipe length required to
achieve the goal.
Example (cont.)
Questions: (1) How to determine the heat transfer coefficient, h?
There are a total of six parameters involved in this problem: h, V, D, , kf,
cp. The temperature dependence of properties is implicit and is only
through the variation of thermal properties. Density  is included in the
kinematic viscosity, /. According to the Buckingham theorem, it is
possible for us to reduce the number of parameters by three. Therefore, the
convection coefficient relationship can be reduced to a function of only
three variables:
Nu=hD/kf, Nusselt number, Re=VD/, Reynolds number, and
Pr=/, Prandtl number.
This conclusion is consistent with empirical observation, that is
Nu=f(Re, Pr). If we can determine the Reynolds and the Prandtl numbers,
we can find the Nusselt number and hence, the heat transfer coefficient, h.
Convection Correlations
 Laminar, fully developed circular pipe flow:
Nu D 
hD
 4.36, when q s "  constant, (page 543, ch. 10-6, ITHT)
kf
Nu D  3.66,
when Ts  constant, (page 543, ch. 10-6, ITHT)
Note: the therma conductivity should be calculated at Tm .
 Fully developed, turbulent pipe flow: Nu  f(Re, Pr),
Nu can be related to Re & Pr experimentally, as shown.
Fixed Re
Fixed Pr
ln(Nu)
slope m
ln(Re)
ln(Nu)
slope n
ln(Pr)
Empirical Correlations
Dittus-Boelter equation: Nu D  0.023 Re 4 / 5 Pr n , (eq 10-76, p 546, ITHT)
where n  0.4 for heating (T s  Tm ), n  0.3 for cooling (Ts  Tm ).
The range of validity: 0.7  Pr  160, Re D  10, 000, L / D  10.
Note: This equation can be used only for moderate temperature difference with all
the properties evaluated at Tm.
Other more accurate correlation equations can be found in other references.
For example,
the Gnielinski
correlation
is the mostcan
accurate
Caution:
The ranges
of application
for these correlations
be quite different.
among all these equations:
Nu D 
( f / 8)(Re D  1000) Pr
(from other reference)
1/ 2
2/3
1  12.7( f / 8) (Pr  1)
It is valid for 0.5  Pr  2000 and 3000  Re D  5  106 .
All properties are calculated at Tm .
Example (cont.)
In our example, we need to first calculate the Reynolds number: water at 35°C,
Cp=4.18(kJ/kg.K), =7x10-4 (N.s/m2), kf=0.626 (W/m.K), Pr=4.8.
VD m A D
4m
4(0.15)
Re 



 5460
4


 D   (0.05)(7  10 )
Re  4000, it is turbulent pipe flow.
Use the Gnielinski correlation, from the Moody chart, f  0.036, Pr  4.8
( f / 8)(Re D  1000) Pr
(0.036 / 8)(5460  1000)(4.8)
Nu D 

 37.4
1/ 2
2/3
1/ 2
2/3
1  12.7( f / 8) (Pr  1) 1  12.7(0.036 / 8) (4.8  1)
kf
0.626
h
NuD 
(37.4)  469(W / m 2 . K )
D
0.05
Energy Balance
Question (2): How can we determine the required pipe length?
Use energy balance concept: (energy storage) = (energy in) minus (energy out).
energy in = energy received during a steady state operation (assume no loss)
q '( L)  mCP (Tout  Tin ),
mCP (Tin  Tout ) (0.15)(4180)(50  20)
L

 94(m)
q'
200
q’=q/L
Tin
Tout
Temperature Distribution
Question (3): Can we determine the water temperature variation along the pipe?
Recognize the fact that the energy balance equation is valid for
any pipe length x:
q '( x )  mCP (T ( x )  Tin )
q'
200
T ( x )  Tin 
x  20 
x  20  0.319 x
mCP
(0.15)(4180)
It is a linear distribution along the pipe
Question (4): How about the surface temperature distribution?
From local Newton's cooling law:
q  hA(Ts  Tm )  q ' x  h( Dx )(Ts ( x )  Tm ( x ))
q'
200
 Tm ( x ) 
 20  0.319 x  22.7  0.319 x (C )
 Dh
 (0.05)(469)
At the end of the pipe, Ts ( x  94)  52.7(C )
Ts ( x ) 
Temperature variation for constant heat flux
60
Constant temperature
difference due to the
constant heat flux.
50
T m( x )
T s( x )
40
30
20
0
20
40
60
80
100
x
Note: These distributions are valid only in the fully developed region. In the
entrance region, the convection condition should be different. In general, the
entrance length x/D10 for a turbulent pipe flow and is usually negligible as
compared to the total pipe length.
Internal Flow Convection
-constant surface temperature case
Another commonly encountered internal convection condition is when the
surface temperature of the pipe is a constant. The temperature distribution in
this case is drastically different from that of a constant heat flux case. Consider
the following pipe flow configuration:
Constant Ts
dx
Tm,o
Tm,
i
Energy change  mCp [(Tm  dTm )  Tm ]
 mCp dTm
Tm
Tm+dTm
Energy in  hA(Ts  Tm )
qs=hA(Ts-Tm)
Energy change  energy in
mCp dTm  hA(Ts  Tm )
Temperature distribution
mC p dTm  hA(Ts  Tm ),
Note: q  hA(Ts  Tm ) is valid locally only, since Tm is not a constant
dTm
hA

, where A  Pdx, and P is the perimeter of the pipe
(Tm  Ts )
mCP
Integrate from the inlet to a diatance x downstream:
Tm ( x )
x hP
x
dTm
P
Tm ,i (Tm  Ts )   0 mCP dx   mCP 0 hdx
ln(Tm  Ts ) |TTmm ,(i x )  
Ph
x, where L is the total pipe length
mCP
and h is the averaged convection coefficient of the pipe between 0 & x.
x
1 x
h   hdx,
or  hdx  hx
0
0
x
Temperature distribution
Tm ( x)  Ts
Ph
 exp(
x), for constant surface temperature
Tm,i  Ts
mCP
Constant surface temperature
Ts
T( x)
Tm(x)
x
The difference between the averaged fluid temperature and the surface
temperature decreases exponentially further downstream along the pipe.
Log-Mean Temperature Difference
For the entire pipe:
Tm ,o  Ts
Tm ,i
To
h ( PL)

 exp( 
)
 Ts
Ti
mCP
hAs
or mCP  
To
ln(
)
Ti
q  mCP (Tm ,o  Tm ,i )  mCP ((Ts  Tm ,i )  (Ts  Tm ,o ))
To  Ti
 mCP ( Ti  To )  hAs
 hAs Tlm
To
ln(
)
Ti
To  Ti
where Tlm 
is called the log mean temperature difference.
To
ln(
)
Ti
This relation is valid for the entire pipe.
Free Convection
A free convection flow field is a self-sustained flow driven by the
presence of a temperature gradient. (As opposed to a forced
convection flow where external means are used to provide the flow.)
As a result of the temperature difference, the density field is not
uniform also. Buoyancy will induce a flow current due to the
gravitational field and the variation in the density field. In general,
a free convection heat transfer is usually much smaller compared to
a forced convection heat transfer. It is therefore important only
when there is no external flow exists.
cold
Flow is unstable and a circulatory
pattern will be induced.
T  
T  
hot
Basic Definitions
Buoyancy effect:
Surrounding fluid, cold, 
Warm, 
Hot plate
Net force=(- gV
The density difference is due to the temperature difference and it can be
characterized by ther volumetric thermal expansion coefficient, b:
1 
1   
1 
b   ( )P  

 T
 T  T
 T
  bT
Grashof Number and Rayleigh Number
Define Grashof number, Gr, as the ratio between the buoyancy force and the
viscous force:
3
3
Gr 
g bTL

2

g b (TS  T ) L
2
• Grashof number replaces the Reynolds number in the convection correlation
equation. In free convection, buoyancy driven flow sometimes dominates the
flow inertia, therefore, the Nusselt number is a function of the Grashof number
and the Prandtle number alone. Nu=f(Gr, Pr). Reynolds number will be
important if there is an external flow. (combined forced and free convection.
• In many instances, it is better to combine the Grashof number and the
Prandtle number to define a new parameter, the Rayleigh number, Ra=GrPr.
The most important use of the Rayleigh number is to characterize the laminar
to turbulence transition of a free convection boundary layer flow. For
example, when Ra>109, the vertical free convection boundary layer flow over
a flat plate becomes turbulent.
Example
Determine the rate of heat loss from a heated pipe as a result of
natural (free) convection.
T=0°C
D=0.1 m
Ts=100C
Film temperature( Tf): averaged boundary layer temperature Tf=1/2(Ts+T )=50 C.
kf=0.03 W/m.K, Pr=0.7, =210-5 m2/s, b=1/Tf=1/(273+50)=0.0031(1/K)
Ra 
g b (TS  T ) L3
2
(9.8)(0.0031)(100  0)(0.1) 3
6
Pr 
(0.7)

7.6

10
.
5 2
(2  10 )
0.387 Ra1/ 6
2
NuD  {0.6 
}
 26.0 (equation 11.15 in Table 11.1)
9 /16 8 / 27
[1  (0.559 / Pr) ]
kf
0.03
h
NuD 
(26)  7.8(W / m 2 K )
D
0.1
q  hA(TS  T )  (7.8)( )( 0.1)(1)(100  0)  244.9(W )
Can be significant if the pipe are long.